The voltage source Vₛ between A and B has its + terminal at B, so it makes VB − VA = Vₛ. Use nodal analysis with a supernode to find the node voltage VB (measured from ground).
A linear resistive circuit contains one voltage source Vs and one current source Is. The current I through a load resistor is measured twice: with Vs = 4 V and Is = 3 mA, I = 3.95 mA; with Vs = 5 V and Is = 8 mA, I = 6 mA. Find the load current I when Vs = 6 V and Is = 10 mA.
4 V, 3 mA → 3.95 mA5 V, 8 mA → 6 mAVs = 6 V, Is = 10 mA
I = mA
8.SuperpositionHard
Use superposition to find the current IR2 through R2 in the direction of the arrow.
The inductor carries a steady current of 2.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the voltage vR across R at t = 5 ms.
i(0) = 2.5 AR = 10 ΩL = 47 mHt = 5 ms
vR = V
14.RC & RL transientsHard
A timer starts charging an uncharged capacitor through a resistor from a 5 V supply at t = 0. It must trigger when the capacitor voltage reaches 3.16 V, exactly 50 ms after the start. With R = 4.7 kΩ, find the capacitance C needed.
Vs = 5 VVth = 3.16 VT = 50 msR = 4.7 kΩ
C = µF
3Solutions
1.Series & parallel resistors
Answer: Req = 4.1 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 2 + 5 = 7 Ω
R2 ∥ 7 = 3·7/(3+7) = 2.1 Ω
Req = R1 + 2.1 = 2 + 2.1 = 4.1 Ω
Answer
Req = 4.1 Ω
2.Series & parallel resistors
Answer: Req = 16.63 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 6 + 3 = 9 Ω
R4 ∥ 9 = 6.923 Ω
R3 + 6.923 = 8.923 Ω
R2 ∥ 8.923 = 1.634 Ω
Req = R1 + 1.634 = 15 + 1.634 = 16.63 Ω
Answer
Req = 16.63 Ω
3.Nodal analysis
Answer: IR3 = 2.917 A
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
Set up the nodes
Ground is the bottom wire. Known node voltages come straight from the sources (V1 = 30 V). Unknowns: VA, VB.
KCL at node A
Currents leaving A through the resistors equal the current pushed into A by sources.
VA/R2 + (VA − V1)/R1 + (VA − VB)/R3 = 0
VA/12 + (VA − 30)/4 + (VA − VB)/5 = 0
0.5333·VA − 0.2·VB = 7.5
KCL at node B
Currents leaving B through the resistors equal the current pushed into B by sources.
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
Form a supernode
The voltage source between A and B carries an unknown current, so KCL cannot be written at A or B separately. Enclose A, B and the source in one supernode: the current entering it equals the current leaving it.
VB = VA + 3
(VA − V1)/R1 + VA/R2 + VB/R3 = Is
Solve
(VA − 24)/2 + VA/4 + (VA + 3)/20 = 0.5
VA·(1/2 + 1/4 + 1/20) = 0.5 + 24/2 − 3/20 = 12.35
VA = 12.35/0.8 = 15.44 V
VB = 18.44 V
Answer
VB = 18.44 V
5.Mesh analysis
Answer: I2 = −0.1923 A
Mesh analysis: give each window of a planar circuit its own loop current, write Kirchhoff’s voltage law around each loop (sum of drops = sum of rises), and solve. Branch currents are the mesh current, or the difference of two mesh currents on a shared branch.
Assign mesh currents
Draw a clockwise current in each window: I1, I2. A resistor shared by two meshes carries the difference of their currents.
KVL around mesh 1
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R1·I1 + R3(I1 − I2) = V1
10·I1 + 12(I1 − I2) = 15
22·I1 − 12·I2 = 15
KVL around mesh 2
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R2·I2 + R3(I2 − I1) = −V2
4·I2 + 12(I2 − I1) = (−10)
−12·I1 + 16·I2 = −10
Solve
Δ = (22)(16) − (−12)(−12) = 208
I1 = Δ1/Δ = 120/208 = 0.5769 A
I2 = Δ2/Δ = −40/208 = −0.1923 A
Answer
I2 = −0.1923 A
A negative mesh current flows anticlockwise.
6.Mesh analysis
Answer: VR4 = 7.464 V
Mesh analysis: give each window of a planar circuit its own loop current, write Kirchhoff’s voltage law around each loop (sum of drops = sum of rises), and solve. Branch currents are the mesh current, or the difference of two mesh currents on a shared branch.
Assign mesh currents
Draw a clockwise current in each window: I1, I2, I3. A resistor shared by two meshes carries the difference of their currents.
KVL around mesh 1
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R1·I1 + R4(I1 − I2) = V1
8·I1 + 8(I1 − I2) = 18
16·I1 − 8·I2 = 18
KVL around mesh 2
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R2·I2 + R4(I2 − I1) + R5(I2 − I3) = 0
6·I2 + 8(I2 − I1) + 15(I2 − I3) = 0
−8·I1 + 29·I2 − 15·I3 = 0
KVL around mesh 3
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R3·I3 + R5(I3 − I2) = −V2
4·I3 + 15(I3 − I2) = (−5)
−15·I2 + 19·I3 = −5
Solve
Δ = det of the coefficient matrix = 4000
I1 = Δ1/Δ = 5268/4000 = 1.317 A
I2 = Δ2/Δ = 1536/4000 = 0.384 A
I3 = Δ3/Δ = 160/4000 = 0.04 A
Answer
IR4 = I1 − I2 = 0.933 A
VR4 = IR4·R4 = 0.933·8 = 7.464 V
A negative mesh current flows anticlockwise.
7.Superposition
Answer: I = 7.3 mA
Superposition: in a linear circuit, any voltage or current is the sum of the responses to each independent source acting alone. To switch a source off, replace an ideal voltage source with a short circuit and an ideal current source with an open circuit. Resistors stay where they are.
Write the response as a sum of contributions
Each contribution is proportional to its own source, with a constant that depends only on the resistors.
I = k₁·Vs + k₂·Is
4·k₁ + 3·k₂ = 3.95
5·k₁ + 8·k₂ = 6
Solve for the constants
Δ = (4)(8) − (3)(5) = 17
k₁ = Δ1/Δ = 13.6/17 = 0.8
k₂ = Δ2/Δ = 4.25/17 = 0.25
k₁ = 0.8 mA/V, k₂ = 0.25
Predict the new current
I = 0.8·6 + 0.25·10 = 7.3 mA
Answer
I = 7.3 mA
8.Superposition
Answer: IR2 = −2.778 A
Superposition: in a linear circuit, any voltage or current is the sum of the responses to each independent source acting alone. To switch a source off, replace an ideal voltage source with a short circuit and an ideal current source with an open circuit. Resistors stay where they are.
Case 1 · V1 acting alone
V₂ becomes a short and Iₛ an open circuit. Seen from A, R₃ is in parallel with the series pair R₂+R₄.
A negative result means the real current flows against the arrow.
9.Thévenin & Norton
Answer: IN = 0.18 A
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 5·4/(5+4) = 2.222 Ω
Rth = (R1 ∥ R2) + R3 = 2.222 + 20 = 22.22 Ω
Find Vth, the open-circuit voltage
With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.
Vth = V1·R2/(R1+R2) = 9·4/(5+4) = 4 V
Norton equivalent
A Norton source is the same circuit seen as a current source in parallel with R_th. Its current is the short-circuit current at a–b.
IN = Vth/Rth = 4/22.22 = 0.18 A
10.Thévenin & Norton
Answer: PL = 54.99 W
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 20·8/(20+8) = 5.714 Ω
Rth = (R1 ∥ R2) + R3 = 5.714 + 6 = 11.71 Ω
Find Vth, the open-circuit voltage
With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.
VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 8.571 + 4·5.714 = 31.43 V
Vth = VB = VA + Is·R3 = 31.43 + 4·6 = 55.43 V
Connect the load to the Thévenin equivalent
The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.
IL = Vth/(Rth + RL) = 55.43/(11.71 + 5) = 3.316 A
PL = IL²·RL = 3.316²·5 = 54.99 W
11.Op-amp circuits
Answer: Vout = 11.88 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Voltage at the + input
V₊ = Vin·Rb/(Ra + Rb) = 4·100/(1 + 100) = 3.96 V
Non-inverting gain
V₋ = V₊, and the current through R₁ also flows through Rf.
Vout = V₊·(1 + Rf/R1) = 3.96·(1 + 2/1) = 11.88 V
Answer
Vout = 11.88 V
12.Op-amp circuits
Answer: If = −0.286 mA
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Input currents
V₋ = 0, so each input resistor has its full input voltage across it.
I1 = V1/R1 = −0.6/2 = −0.3 mA
I2 = V2/R2 = 1.4/100 = 0.014 mA
If = I1 + I2 = −0.286 mA
Answer
If = −0.286 mA
13.RC & RL transients
Answer: vR = 8.628 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant
τ = L/R = 47 mH / 10 Ω = 4.7 ms
Decay of the current
i(t) = 2.5·e−5/4.7 = 0.8628 A
vR = R·i = 10·0.8628 = 8.628 V
Answer
vR = 8.628 V
14.RC & RL transients
Answer: C = 10.64 µF
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.