Three branches are connected between node A and ground, as shown. Use nodal analysis to find the current I2 in branch 2, flowing up into node A in the direction of the arrow.
The diamond is a voltage-controlled current source that pushes a current of 0.05·VA (in A, with VA in V) up into node B. Use nodal analysis to find the current IR4 through R4 in the direction of the arrow.
The inductor carries no current before the switch closes at t = 0. Find the voltage vL across the inductor at t = 5 ms.
Vs = 5 VR = 33 ΩL = 68 mHt = 5 ms
vL = V
14.RC & RL transientsHard
The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage vC at t = 200 ms.
Vs = 6 VR1 = 3.3 kΩR2 = 10 kΩC = 68 µFt = 200 ms
vC = V
3Solutions
1.Series & parallel resistors
Answer: Req = 13 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 15 + 15 = 30 Ω
R2 ∥ 30 = 6·30/(6+30) = 5 Ω
Req = R1 + 5 = 8 + 5 = 13 Ω
Answer
Req = 13 Ω
2.Series & parallel resistors
Answer: Req = 24.18 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 4 + 15 = 19 Ω
R4 ∥ 19 = 5.63 Ω
R3 + 5.63 = 25.63 Ω
R2 ∥ 25.63 = 4.184 Ω
Req = R1 + 4.184 = 20 + 4.184 = 24.18 Ω
Answer
Req = 24.18 Ω
3.Nodal analysis
Answer: I2 = 0.6316 A
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
KCL at node A
Take the bottom wire as ground. Each branch carries (VA − Vk)/Rk away from A, where Vk is the voltage of its source (zero for a plain resistor). The currents leaving A add up to zero.
(VA − 24)/5 + (VA − 24)/3 + (VA − 12)/10 = 0
Solve for VA
VA = (24/5 + 24/3 + 12/10) / (1/5 + 1/3 + 1/10) = 14/0.6333 = 22.11 V
Branch current
The arrow points up through the branch, into node A.
I2 = (24 − VA)/R2 = (24 − 22.11)/3 = 0.6316 A
Answer
I2 = 0.6316 A
A negative result means the real current flows against the arrow.
4.Nodal analysis
Answer: IR4 = 1.091 A
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
KCL at node A
Currents leaving A through the resistors equal the current pushed into A by sources.
(VA − V1)/R1 + VA/R2 + (VA − VB)/R3 = 0
0.19·VA − 0.1·VB = 1.44
KCL at node B
The dependent source pushes g·VA into node B. Treat it like an independent source, then move the VA term to the left-hand side.
(VB − VA)/R3 + VB/R4 = 0.05·VA
−0.15·VA + 0.6·VB = 0
Solve
Δ = (0.19)(0.6) − (−0.1)(−0.15) = 0.099
VA = Δ1/Δ = 0.864/0.099 = 8.727 V
VB = Δ2/Δ = 0.216/0.099 = 2.182 V
Current through R₄
IR4 = VB/R4 = 2.182/2 = 1.091 A
Answer
IR4 = 1.091 A
5.Mesh analysis
Answer: IR2 = −0.6102 A
Mesh analysis: give each window of a planar circuit its own loop current, write Kirchhoff’s voltage law around each loop (sum of drops = sum of rises), and solve. Branch currents are the mesh current, or the difference of two mesh currents on a shared branch.
Assign mesh currents
Draw a clockwise current in each window: I1, I2. A resistor shared by two meshes carries the difference of their currents.
KVL around mesh 1
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R1·I1 + R3(I1 − I2) = V1
5·I1 + 6(I1 − I2) = 10
11·I1 − 6·I2 = 10
KVL around mesh 2
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R2·I2 + R3(I2 − I1) = −V2
8·I2 + 6(I2 − I1) = (−12)
−6·I1 + 14·I2 = −12
Solve
Δ = (11)(14) − (−6)(−6) = 118
I1 = Δ1/Δ = 68/118 = 0.5763 A
I2 = Δ2/Δ = −72/118 = −0.6102 A
Answer
IR2 = I2 = −0.6102 A
A negative mesh current flows anticlockwise.
6.Mesh analysis
Answer: VR1 = 32.58 V
Mesh analysis: give each window of a planar circuit its own loop current, write Kirchhoff’s voltage law around each loop (sum of drops = sum of rises), and solve. Branch currents are the mesh current, or the difference of two mesh currents on a shared branch.
Assign mesh currents
Draw a clockwise current in each window: I1, I2, I3. A resistor shared by two meshes carries the difference of their currents.
KVL around mesh 1
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R1·I1 + R4(I1 − I2) = V1
25·I1 + 3(I1 − I2) = 36
28·I1 − 3·I2 = 36
KVL around mesh 2
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R2·I2 + R4(I2 − I1) + R5(I2 − I3) = 0
10·I2 + 3(I2 − I1) + 3(I2 − I3) = 0
−3·I1 + 16·I2 − 3·I3 = 0
KVL around mesh 3
Going clockwise, the voltage drops across resistors equal the source voltage rises (− to + in the direction of travel).
R3·I3 + R5(I3 − I2) = −V2
30·I3 + 3(I3 − I2) = (−15)
−3·I2 + 33·I3 = −15
Solve
Δ = det of the coefficient matrix = 14235
I1 = Δ1/Δ = 18549/14235 = 1.303 A
I2 = Δ2/Δ = 2304/14235 = 0.1619 A
I3 = Δ3/Δ = −6261/14235 = −0.4398 A
Answer
IR1 = I1 = 1.303 A
VR1 = IR1·R1 = 1.303·25 = 32.58 V
A negative mesh current flows anticlockwise.
7.Superposition
Answer: IR2 = 1.898 A
Superposition: in a linear circuit, any voltage or current is the sum of the responses to each independent source acting alone. To switch a source off, replace an ideal voltage source with a short circuit and an ideal current source with an open circuit. Resistors stay where they are.
Case 1 · V1 acting alone
Iₛ becomes an open circuit, so R₃ and R₄ form one series branch from A to ground, in parallel with R₂.
R3+R4 = 20+5 = 25 Ω
R2 ∥ (R3+R4) = 4·25/(4+25) = 3.448 Ω
VA = 18·3.448/(4+3.448) = 8.333 V
VB = VA·R4/(R3+R4) = 8.333·5/25 = 1.667 V
IR2′ = (VA − 0)/R2 = (8.333 − 0)/4 = 2.083 A
Case 2 · Is acting alone
V₁ becomes a short, so R₁ is in parallel with R₂. Iₛ splits at B between R₄ and the path through R₃.
R1 ∥ R2 = 4·4/(4+4) = 2 Ω
Req = R4 ∥ (R3+R1∥R2) = 5 ∥ 22 = 4.074 Ω
VB = Is·Req = (−2)·4.074 = −8.148 V
VA = VB·(R1∥R2)/(R3+R1∥R2) = −8.148·2/22 = −0.7407 V
IR2″ = (VA − 0)/R2 = (−0.7407 − 0)/4 = −0.1852 A
Add the contributions
IR2 = IR2′ + IR2″
IR2 = 2.083 + (−0.1852) = 1.898 A
A negative result means the real current flows against the arrow.
8.Superposition
Answer: IR2 = 0.521 A
Superposition: in a linear circuit, any voltage or current is the sum of the responses to each independent source acting alone. To switch a source off, replace an ideal voltage source with a short circuit and an ideal current source with an open circuit. Resistors stay where they are.
Case 1 · V1 acting alone
V₂ becomes a short and Iₛ an open circuit. Seen from A, R₃ is in parallel with the series pair R₂+R₄.
A negative result means the real current flows against the arrow.
9.Thévenin & Norton
Answer: Vth = 3.6 V
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 10·15/(10+15) = 6 Ω
Rth = (R1 ∥ R2) + R3 = 6 + 15 = 21 Ω
Find Vth, the open-circuit voltage
With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.
Vth = V1·R2/(R1+R2) = 6·15/(10+15) = 3.6 V
10.Thévenin & Norton
Answer: PL = 11.11 W
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 25·15/(25+15) = 9.375 Ω
Rth = (R1 ∥ R2) + R3 = 9.375 + 5 = 14.38 Ω
Find Vth, the open-circuit voltage
With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.
VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 11.25 + 1·9.375 = 20.63 V
Vth = VB = VA + Is·R3 = 20.63 + 1·5 = 25.63 V
Connect the load to the Thévenin equivalent
The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.
IL = Vth/(Rth + RL) = 25.63/(14.38 + 20) = 0.7455 A
PL = IL²·RL = 0.7455²·20 = 11.11 W
11.Op-amp circuits
Answer: Rf = 100 kΩ
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Gain of a non-inverting amplifier
V₋ = V₊ = Vin, and the current through R₁ also flows through Rf, so Vout = Vin·(1 + Rf/R₁).
Av = 1 + Rf/R1
Rf = (2 − 1)·100 = 100 kΩ
Answer
Rf = 100 kΩ
12.Op-amp circuits
Answer: Vout = 0.8545 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Input currents
V₋ = 0, so each input resistor has its full input voltage across it.
I1 = V1/R1 = 1.8/22 = 0.08182 mA
I2 = V2/R2 = −0.2/2 = −0.1 mA
If = I1 + I2 = −0.01818 mA
Output voltage
Vout = −Rf·If = −47·(−0.01818) = 0.8545 V
Answer
Vout = 0.8545 V
13.RC & RL transients
Answer: vL = 0.4417 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant and final current
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
τ = L/R = 68 mH / 33 Ω = 2.061 ms
i(∞) = Vs/R = 5/33 = 0.1515 A
Inductor voltage
At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.
vL(t) = Vs·e−t/τ = 5·e−5/2.061 = 0.4417 V
Answer
vL = 0.4417 V
14.RC & RL transients
Answer: vC = 3.362 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Initial capacitor voltage
In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.