Decide which form suits the operation: rectangular a + jb for adding and subtracting, polar r∠θ for multiplying, dividing, powers and roots.
Multiply out with j² = −1; divide by multiplying the top and bottom by the conjugate of the denominator.
Convert with r = √(a² + b²) and θ from a sketch of the point (check the quadrant), and back with a = r cos θ, b = r sin θ.
For powers use De Moivre, (r∠θ)ⁿ = rⁿ∠nθ; for zⁿ = R∠φ list all n roots R1/n∠((φ + 360°k)/n).
AC impedance & phasors
Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z
Method
Convert the frequency: ω = 2πf.
Find each reactance: XL = ωL and XC = 1/(ωC).
Add impedances like resistors, with Z = R + jX.
Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.
AC power & power factor
Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)
LC resonance, Q factor & bandwidth
Natural frequency
ω0 = 1/√(LC), f0 = 1/(2π√(LC))
Energy
W = ½CV0² = ½Cv² + ½Li²
Peak current
Imax = V0√(C/L)
Quality factor
Q = 2π·(energy stored)/(energy lost per cycle)
Series RLC
Q = (1/R)√(L/C), BW = R/(2πL)
Parallel RLC
Q = R√(C/L), BW = 1/(2πRC)
Bandwidth
BW = f2 − f1 = f0/Q, f0 = √(f1f2)
Half-power frequencies
f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q))
Tank with coil resistance r
RD = L/(C·r) = Q²·r
Decay of the amplitude
e−Rt/(2L)
Method
Find the resonance frequency first: ω₀ = 1/√(LC) and f₀ = ω₀/(2π).
Decide whether the circuit is series or parallel: series Q = (1/R)√(L/C), parallel Q = R√(C/L).
Use BW = f₀/Q for the bandwidth, or the shortcuts R/(2πL) (series) and 1/(2πRC) (parallel).
For energy questions, use that the total energy ½CV₀² stays constant in an ideal LC circuit and swings between C and L every quarter period.
Three-phase power
Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η
RC & RL transients
Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ
Method
Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.
Thévenin & Norton
Thévenin voltage
Vth = Vopen circuit
Thévenin resistance
Rth: all sources off, seen from a–b
Norton current
IN = Vth/Rth
Load current
IL = Vth/(Rth + RL)
Maximum power transfer
RL = Rth, Pmax = Vth²/(4Rth)
Method
Remove the load and mark the two terminals a and b.
Find the open-circuit voltage between a and b: this is Vth.
Switch off all independent sources and find the resistance seen from a–b: this is Rth.
Put the load back on the equivalent circuit: Vth in series with Rth.
For the Norton equivalent, convert: IN = Vth/Rth, with RN = Rth in parallel.
2Practice problems
1.Complex numbersMedium
Find the argument θ of z = −8 + j in degrees, as the principal value between −180° and 180°.
z = −8 + j
θ = °
2.Complex numbersHard
Exactly one of the points A–D is a root of z⁶ = 729∠60°. Click it.
w = 729∠60°n = 6
1A (3∠−110°)
2B (5.4∠−80°)
3C (3∠−80°)
4D (3∠60°)
3.AC impedance & phasorsMedium
A resistor and a capacitor are connected in parallel across a 12 V (rms), 100 Hz supply. Find the magnitude of the impedance |Z|.
V = 12 V (rms)f = 100 HzR = 60 ΩC = 22 µF
|Z| = Ω
4.AC impedance & phasorsHard
A series RLC circuit is connected to a 50 V (rms), 50 Hz supply. Find the rms current I.
V = 50 V (rms)f = 50 HzR = 60 ΩL = 250 mHC = 100 µF
I = A
5.AC power & power factorMedium
A single-phase motor takes 23 kW at a power factor of 0.7 lagging from a 230 V supply. Find the line current I.
P = 23 kWpf = 0.7V = 230 V
I = A
6.AC power & power factorHard
A single-phase load takes 10 kW at a power factor of 0.65 lagging from a 400 V, 50 Hz supply. A 68 µF capacitor is connected in parallel with the load. Find the new line current I.
P = 10 kWpf1 = 0.65V = 400 Vf = 50 HzC = 68 µF
I = A
7.LC resonance, Q factor & bandwidthMedium
A parallel RLC circuit has R = 4.7 kΩ, L = 470 µH and C = 470 pF. Find its quality factor Q.
R = 4.7 kΩL = 470 µHC = 470 pF
Q =
8.LC resonance, Q factor & bandwidthHard
The half-power frequencies of a resonance curve are 1 kHz and 1.6 kHz. Find the resonance frequency as their geometric mean, and then the quality factor Q.
f1 = 1 kHzf2 = 1.6 kHz
Q =
9.Three-phase powerMedium
A balanced three-phase load draws a line current of 40 A from a supply with a line-to-line voltage of 480 V. The power factor is 0.88 lagging. Find the total real power P drawn by the load in kW.
VL = 480 VIL = 40 Acos φ = 0.88
P = kW
10.Three-phase powerHard
A balanced three-phase load takes 250 kW at a power factor of 0.65 lagging from a 480 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.9 lagging. The real power stays the same. Find the total reactive power QC the capacitor bank must supply, in kvar.
P = 250 kWpf1 = 0.65pf2 = 0.9VL = 480 Vf = 50 Hz
QC = kvar
11.RC & RL transientsMedium
The inductor carries a steady current of 1.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the current i at t = 15 ms.
i(0) = 1.5 AR = 15 ΩL = 100 mHt = 15 ms
i = A
12.RC & RL transientsHard
A timer starts charging an uncharged capacitor through a resistor from a 12 V supply at t = 0. It must trigger when the capacitor voltage reaches 9 V, exactly 500 ms after the start. With R = 10 kΩ, find the capacitance C needed.
Vs = 12 VVth = 9 VT = 500 msR = 10 kΩ
C = µF
13.Thévenin & NortonMedium
Find the Thévenin voltage Vth seen from terminals a–b.
V1 = 30 VR1 = 2 ΩR2 = 6 ΩR3 = 20 Ω
Vth = V
14.Thévenin & NortonHard
A load RL = 8 Ω is connected across a–b. Replace the rest of the circuit with its Thévenin equivalent and find the load current IL.
The RC high-pass filter shown has R = 10 kΩ, C = 1 nF. A sinusoidal input of 64 kHz is applied. Find the phase shift φ of vout relative to vin, in degrees.
R = 10 kΩC = 1 nFf = 64 kHz
φ = °
16.Bode plots & marginsHard
A unity-feedback loop has the open-loop transfer function L(s) = 1210/(s(s + 9)(s + 10)). Find the gain margin GM in dB.
L(s) = 1210/(s(s + 9)(s + 10))
GM = dB
3Solutions
1.Complex numbers
Answer: θ = 172.9 °
Polar form: z = r∠θ = r(cos θ + j sin θ) = r·ejθ, with r = |z| and θ = arg z. Back to rectangular form: a = r cos θ, b = r sin θ. The argument needs the quadrant: θ = atan(b/a) only when a > 0; for a < 0 add or subtract 180°. In polar form multiplication is easy: multiply the moduli and add the arguments; for division divide the moduli and subtract the arguments.
Quadrant
a = −8, b = 1 → II
Reference angle
α = atan(1/8) = 7.125°
Argument
θ = 180° − α = 172.9°
Answer
θ = 172.9°
In polar form z = 8.062∠172.9°.
2.Complex numbers
Answer: A (3∠−110°)
De Moivre and roots: (r∠θ)ⁿ = rⁿ∠nθ. The equation zⁿ = R∠φ has exactly n roots, all with modulus R1/n, at the arguments (φ + 360°·k)/n for k = 0, 1, …, n − 1: they lie evenly spaced on a circle, 360°/n apart. A quadratic z² + pz + q = 0 with p² < 4q has the complex roots z = −p/2 ± j√(q − p²/4); a polynomial with real coefficients always has its complex roots in conjugate pairs a ± jb.
Modulus and arguments of the roots
|z| = 3
θ = 10°, 70°, 130°, −170°, −110°, −50°
The point
A = 3∠−110°
Answer
A (3∠−110°)
3.AC impedance & phasors
Answer: |Z| = 46.18 Ω
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Reactance
XC = 1/(ωC) = 1/(2π·100·22·10⁻⁶) = 72.34 Ω
Branch currents
Both branches are connected straight across the supply, so each sees the full voltage V.
IR = V/R = 12/60 = 0.2 A
IX = V/XC = 12/72.34 = 0.1659 A
Total current
The resistor current is in phase with V and the reactive current is 90° out of phase, so they add like the sides of a right triangle.
I = √(IR² + IX²) = √(0.2² + 0.1659²) = 0.2598 A
Impedance
|Z| = V/I = 12/0.2598 = 46.18 Ω
Answer
|Z| = 46.18 Ω
4.AC impedance & phasors
Answer: I = 0.6576 A
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Reactances
ω = 2πf = 2π·50 = 314.2 rad/s
XL = ωL = 314.2·0.25 = 78.54 Ω
XC = 1/(ωC) = 1/(314.2·100·10⁻⁶) = 31.83 Ω
Impedance
In series the impedances add as complex numbers: Z = R + j(XL − XC).
The same current flows through every element of a series circuit.
I = V/|Z| = 50/76.04 = 0.6576 A
Answer
I = 0.6576 A
5.AC power & power factor
Answer: I = 142.9 A
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Line current
Only the real part of the power does work, so divide by the power factor.
I = P/(V·cos φ) = 23000/(230·0.7) = 142.9 A
Answer
I = 142.9 A
6.AC power & power factor
Answer: I = 32.45 A
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Reactive power before and after
The real power P does not change; only the reactive power drawn from the supply does.
Q1 = 10·tan(arccos 0.65) = 11.69 kvar
QC = V²·2πf·C = 400²·2π·50·68·10⁻⁶ = 3418 var = 3.418 kvar
Q2 = 11.69 − 3.418 = 8.273 kvar
New apparent power
S2 = √(10² + 8.273²) = 12.98 kVA
New line current
I = S2/V = 12979/400 = 32.45 A
Answer
I = 32.45 A
7.LC resonance, Q factor & bandwidth
Answer: Q = 4.7
Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).
Resonance frequency
ω₀ = 1/√(LC) = 2.128 × 10⁶ rad/s
Quality factor
Q = R/(ω₀L) = 4700/(2.128 × 10⁶·0.00047) = 4.7
Answer
Q = 4.7
The bandwidth is 1/(2πRC) = 72.05 kHz.
8.LC resonance, Q factor & bandwidth
Answer: Q = 2.108
Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).
Resonance frequency
f0 = √(1000·1600) = 1265 Hz
Bandwidth
BW = 1600 − 1000 = 600 Hz
Quality factor
Q = 1265/600 = 2.108
Answer
Q = 2.108
9.Three-phase power
Answer: P = 29.26 kW
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Apparent power
S = √3·VL·IL = √3·480·40 = 33.26 kVA
Real power
P = S·cos φ = 33.26·0.88 = 29.26 kW
Answer
P = 29.26 kW
10.Three-phase power
Answer: QC = 171.2 kvar
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
Reactive power before and after
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.
Q1 = 250·tan(acos 0.65) = 250·1.169 = 292.3 kvar
Q2 = 250·tan(acos 0.9) = 250·0.4843 = 121.1 kvar
Reactive power from the capacitors
QC = Q1 − Q2 = 171.2 kvar
Answer
QC = 171.2 kvar
11.RC & RL transients
Answer: i = 0.1581 A
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant
τ = L/R = 100 mH / 15 Ω = 6.667 ms
Decay of the current
i(t) = 1.5·e−15/6.667 = 0.1581 A
Answer
i = 0.1581 A
12.RC & RL transients
Answer: C = 36.07 µF
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Required time constant
9 = 12·(1 − e−500/τ) → τ = 500/ln(12/(12 − 9))
τ = 500/1.386 = 360.7 ms
Capacitance
kΩ times µF gives milliseconds.
C = τ/R = 360.7/10 = 36.07 µF
Answer
C = 36.07 µF
13.Thévenin & Norton
Answer: Vth = 22.5 V
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 2·6/(2+6) = 1.5 Ω
Rth = (R1 ∥ R2) + R3 = 1.5 + 20 = 21.5 Ω
Find Vth, the open-circuit voltage
With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.
Vth = V1·R2/(R1+R2) = 30·6/(2+6) = 22.5 V
14.Thévenin & Norton
Answer: IL = 3.44 A
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Find Rth with every source switched off
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
R1 ∥ R2 = 15·12/(15+12) = 6.667 Ω
Rth = (R1 ∥ R2) + R3 = 6.667 + 2 = 8.667 Ω
Find Vth, the open-circuit voltage
With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.
VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 5.333 + 6·6.667 = 45.33 V
Vth = VB = VA + Is·R3 = 45.33 + 6·2 = 57.33 V
Connect the load to the Thévenin equivalent
The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.
IL = Vth/(Rth + RL) = 57.33/(8.667 + 8) = 3.44 A
15.Bode plots & margins
Answer: φ = 13.97 °
Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.
Corner frequency
ωc = 1/(RC) = 1/(10000·1 × 10⁻⁹) = 100000 rad/s
fc = 15915 Hz → f/fc = 64000/15915 = 4.021
Phase
φ = 90° − atan(4.021) = 13.97°
Answer
φ = 13.97°
16.Bode plots & margins
Answer: GM = 3.004 dB
Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.