Circuit Analysis 2: AC circuits: cram pack

Formula sheets, the key method steps for every topic and 16 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Complex numbers

Rectangular form
z = a + jb, j² = −1, z̄ = a − jb
Modulus and argument
|z| = √(a² + b²), tan θ = b/a (check the quadrant)
Polar and exponential form
z = r∠θ = r(cos θ + j sin θ) = r·ejθ
Division
z₁/z₂ = z₁z̄₂/|z₂|²
Product and quotient
r₁∠θ₁ · r₂∠θ₂ = r₁r₂∠(θ₁ + θ₂), r₁∠θ₁ / r₂∠θ₂ = (r₁/r₂)∠(θ₁ − θ₂)
De Moivre
(r∠θ)ⁿ = rⁿ∠nθ
n-th roots
zk = R1/n∠((φ + 360°·k)/n), k = 0 … n − 1
Quadratic with p² < 4q
z = −p/2 ± j√(q − p²/4)

Method

  1. Decide which form suits the operation: rectangular a + jb for adding and subtracting, polar r∠θ for multiplying, dividing, powers and roots.
  2. Multiply out with j² = −1; divide by multiplying the top and bottom by the conjugate of the denominator.
  3. Convert with r = √(a² + b²) and θ from a sketch of the point (check the quadrant), and back with a = r cos θ, b = r sin θ.
  4. For powers use De Moivre, (r∠θ)ⁿ = rⁿ∠nθ; for zⁿ = R∠φ list all n roots R1/n∠((φ + 360°k)/n).

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

LC resonance, Q factor & bandwidth

Natural frequency
ω0 = 1/√(LC), f0 = 1/(2π√(LC))
Energy
W = ½CV0² = ½Cv² + ½Li²
Peak current
Imax = V0√(C/L)
Quality factor
Q = 2π·(energy stored)/(energy lost per cycle)
Series RLC
Q = (1/R)√(L/C), BW = R/(2πL)
Parallel RLC
Q = R√(C/L), BW = 1/(2πRC)
Bandwidth
BW = f2 − f1 = f0/Q, f0 = √(f1f2)
Half-power frequencies
f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q))
Tank with coil resistance r
RD = L/(C·r) = Q²·r
Decay of the amplitude
e−Rt/(2L)

Method

  1. Find the resonance frequency first: ω₀ = 1/√(LC) and f₀ = ω₀/(2π).
  2. Decide whether the circuit is series or parallel: series Q = (1/R)√(L/C), parallel Q = R√(C/L).
  3. Use BW = f₀/Q for the bandwidth, or the shortcuts R/(2πL) (series) and 1/(2πRC) (parallel).
  4. For energy questions, use that the total energy ½CV₀² stays constant in an ideal LC circuit and swings between C and L every quarter period.

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Thévenin & Norton

Thévenin voltage
Vth = Vopen circuit
Thévenin resistance
Rth: all sources off, seen from a–b
Norton current
IN = Vth/Rth
Load current
IL = Vth/(Rth + RL)
Maximum power transfer
RL = Rth, Pmax = Vth²/(4Rth)

Method

  1. Remove the load and mark the two terminals a and b.
  2. Find the open-circuit voltage between a and b: this is Vth.
  3. Switch off all independent sources and find the resistance seen from a–b: this is Rth.
  4. Put the load back on the equivalent circuit: Vth in series with Rth.
  5. For the Norton equivalent, convert: IN = Vth/Rth, with RN = Rth in parallel.

2Practice problems

1.Complex numbersMedium
ReIm11−1−122−2−233−3−344−4−455−5−5zABCD

The diagram shows z = 1 + j2. With w = 2∠90°, click the point that represents z·w.

z = 1 + j2w = 2∠90°
  1. 1A (−2 + j)
  2. 2B (−4 + j2)
  3. 3C (2 + j4)
  4. 4D (4 − j2)
2.Complex numbersHard
ReIm11−1−122−2−233−3−3z₁z₂

One root of z³ − 5z² + 16z − 30 = 0 is z₁ = 1 + j3. The coefficients are real. Find the real root r.

z₁ = 1 + j3
r =
3.AC impedance & phasorsMedium
12 V200 HzR = 10 ΩL = 250 mHC = 2.2 µFI

A series RLC circuit is connected to a 12 V (rms), 200 Hz supply. Find the power factor cos φ of the circuit.

V = 12 V (rms)f = 200 HzR = 10 ΩL = 250 mHC = 2.2 µF
cos φ =
4.AC impedance & phasorsHard
VfR = 5 ΩL = 50 mHC = 0.22 µF

A series RLC circuit has R = 5 Ω, L = 50 mH and C = 0.22 µF. Find its bandwidth B (the width of the band between the half-power frequencies), in Hz.

R = 5 ΩL = 50 mHC = 0.22 µF
B = Hz
5.AC power & power factorMedium
230 VR + jXP = 2444 W12.5 A

An inductive load takes 12.5 A and 2444 W from a 230 V (rms) single-phase supply. Model it as a resistance R in series with a reactance X. Find R.

V = 230 VI = 12.5 AP = 2444 W
R = Ω
6.AC power & power factorHard
24 V50 HzRs​ = 8 ΩXs​ = j40 ΩZL​ = ?

A 24 V (rms), 50 Hz source has an internal impedance Zs = 8 + j40 Ω. The load impedance ZL can be chosen freely. Find the maximum real power Pmax that can be delivered to the load.

Vs = 24 V (rms)f = 50 HzZs = 8 + j40 Ω
Pmax = W
7.LC resonance, Q factor & bandwidthMedium
V220 Ω1 mH1 nF

A series RLC circuit has R = 220 Ω, L = 1 mH and C = 1 nF. Find its bandwidth BW in kHz.

R = 220 ΩL = 1 mHC = 1 nF
BW = kHz
8.LC resonance, Q factor & bandwidthHard
V5 ΩLC = ?

Design a series RLC filter with a total resistance of 5 Ω, a resonance frequency of 50 kHz and a bandwidth of 2 kHz. Find the capacitance C in nF.

R = 5 Ωf0 = 50 kHzBW = 2 kHz
C = nF
9.Three-phase powerMedium
ABCVL​ = 690 VIL​ = ?M30 kW, η = 91%cos φ = 0.85

A three-phase induction motor delivers 30 kW of mechanical output power at full load. At this load its efficiency is 91% and its power factor is 0.85 lagging. The supply has a line-to-line voltage of 690 V. Find the line current IL.

Pout = 30 kWη = 91%cos φ = 0.85VL = 690 V
IL = A
10.Three-phase powerHard
P = 120 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 120 kW at a power factor of 0.75 lagging from a 415 V (line-to-line), 60 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.95 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 120 kWpf1 = 0.75pf2 = 0.95VL = 415 Vf = 60 Hz
Cph = µF
11.RC & RL transientsMedium
+−Vs​20 Vt = 0R = 15 ΩL68 mHi(t)

The inductor carries no current before the switch closes at t = 0. Find the voltage vL across the inductor at t = 10 ms.

Vs = 20 VR = 15 ΩL = 68 mHt = 10 ms
vL = V
12.RC & RL transientsHard
+−Vs​24 Vopens at t = 0R1​ = 3.3 kΩR2​ = 3.3 kΩi2​C47 µF+−vC​

The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the current i2 through R2 at t = 250 ms.

Vs = 24 VR1 = 3.3 kΩR2 = 3.3 kΩC = 47 µFt = 250 ms
i2 = mA
13.Thévenin & NortonMedium
R1​ = 20 ΩR3​ = 4 Ω+−V1​18 VR2​12 ΩAab

Find the Thévenin voltage Vth seen from terminals a–b.

V1 = 18 VR1 = 20 ΩR2 = 12 ΩR3 = 4 Ω
Vth = V
14.Thévenin & NortonHard
R1​ = 20 ΩR3​ = 2 Ω+−V1​12 VR2​2 ΩAIs​4 ABab

Find the Norton current IN: the current that flows from a to b if the terminals are shorted.

V1 = 12 VIs = 4 AR1 = 20 ΩR2 = 2 ΩR3 = 2 Ω
IN = A
15.Bode plots & marginsMedium
vin​L = 100 mHR = 470 Ωvout​

The RL low-pass filter shown has R = 470 Ω, L = 100 mH. A sinusoidal input of 7.5 kHz is applied. Find the gain |H| = |vout/vin| in dB.

R = 470 ΩL = 100 mHf = 7.5 kHz
|H| = dB
16.Bode plots & marginsHard
|H| (dB)0.10.1111010100100−80−60−40−2002040ω (rad/s)φ (°)ω (rad/s)−270−180−900ω180​ = ?

A unity-feedback loop has the open-loop transfer function L(s) = 102/(s(s + 4)(s + 5)). Find the phase crossover frequency ω180, where ∠L(jω) = −180°.

L(s) = 102/(s(s + 4)(s + 5))
ω180 = rad/s

3Solutions

1.Complex numbers

Answer: B (−4 + j2)

Polar form: z = r∠θ = r(cos θ + j sin θ) = r·ejθ, with r = |z| and θ = arg z. Back to rectangular form: a = r cos θ, b = r sin θ. The argument needs the quadrant: θ = atan(b/a) only when a > 0; for a < 0 add or subtract 180°. In polar form multiplication is easy: multiply the moduli and add the arguments; for division divide the moduli and subtract the arguments.

Effect of w

|z·w| = 2·|z|, arg(z·w) = arg z + 90°

The point

z·w = −4 + j2 → B

Answer

B (−4 + j2)
2.Complex numbers

Answer: r = 3

De Moivre and roots: (r∠θ)ⁿ = rⁿ∠nθ. The equation zⁿ = R∠φ has exactly n roots, all with modulus R1/n, at the arguments (φ + 360°·k)/n for k = 0, 1, …, n − 1: they lie evenly spaced on a circle, 360°/n apart. A quadratic z² + pz + q = 0 with p² < 4q has the complex roots z = −p/2 ± j√(q − p²/4); a polynomial with real coefficients always has its complex roots in conjugate pairs a ± jb.

Conjugate pair

z₂ = 1 − j3
(z − z₁)(z − z₂) = z² − 2·1·z + (1² + 3²) = z² − 2z + 10

Factor out the quadratic

z³ − 5z² + 16z − 30 = (z² − 2z + 10)(z − 3)

Real root

r = 3

Answer

r = 3

Check with the sum of the roots: z₁ + z₂ + r = 2 + 3 = 5 = −(−5).

3.AC impedance & phasors

Answer: cos φ = 0.2058

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

XL = 314.2 Ω, XC = 361.7 Ω

Impedance

|Z| = √(10² + (−47.56)²) = 48.6 Ω

Power factor

cos φ = R/|Z| = 10/48.6 = 0.2058
The circuit is capacitive, so the power factor is leading.

Answer

cos φ = 0.2058
4.AC impedance & phasors

Answer: B = 15.92 Hz

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonant frequency

f0 = 1/(2π·√(0.05·0.22·10⁻⁶)) = 1517 Hz

Quality factor

Q compares the reactance at resonance with the resistance: Q = ω₀L/R.

Q = (1/R)·√(L/C) = (1/5)·√(0.05/(0.22·10⁻⁶)) = 95.35

Bandwidth

B = f0/Q = 1517/95.35 = 15.92 Hz

Answer

B = 15.92 Hz
5.AC power & power factor

Answer: R = 15.64 Ω

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Resistance from the real power

R = P/I² = 2444/12.5² = 15.64 Ω

Answer

R = 15.64 Ω
6.AC power & power factor

Answer: Pmax = 18 W

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Conjugate match

The load reactance cancels the source reactance, and the load resistance equals the source resistance.

ZL = Zs* = 8 − j40 Ω

Maximum power

I = Vs/(2Rs) = 24/16 = 1.5 A
Pmax = I²·RL = Vs²/(4Rs) = 24²/(4·8) = 18 W

Answer

Pmax = 18 W
7.LC resonance, Q factor & bandwidth

Answer: BW = 35.01 kHz

Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).

Bandwidth in rad/s

R/L = 220/0.001 = 220000 rad/s

Bandwidth in Hz

BW = 220000/(2π) = 35014 Hz = 35.01 kHz

Answer

BW = 35.01 kHz

With f₀ = 159.2 kHz this gives Q = 4.545.

8.LC resonance, Q factor & bandwidth

Answer: C = 25.46 nF

Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).

Inductance from the bandwidth

L = R/(2π·BW) = 5/(2π·2000) = 0.0003979 H

Capacitance from the resonance frequency

C = 1/((2π·50000)²·0.0003979) = 2.546 × 10⁻⁸ F = 25.46 nF

Answer

C = 25.46 nF

Q = f₀/BW = 25.

9.Three-phase power

Answer: IL = 32.45 A

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Electrical input power

Pin = Pout/η = 30/0.91 = 32.97 kW

Line current

IL = Pin/(√3·VL·cos φ) = 32967/(√3·690·0.85) = 32.45 A

Answer

IL = 32.45 A
10.Three-phase power

Answer: Cph = 1022 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 120·tan(acos 0.75) = 120·0.8819 = 105.8 kvar
Q2 = 120·tan(acos 0.95) = 120·0.3287 = 39.44 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 66.39 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 415/√3 = 239.6 V, ω = 2π·60 = 377 rad/s
Cph = (QC/3)/(ω·V²) = 22129/(377·239.6²) = 1022 µF

Answer

Cph = 1022 µF
11.RC & RL transients

Answer: vL = 2.203 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 68 mH / 15 Ω = 4.533 ms
i(∞) = Vs/R = 20/15 = 1.333 A

Inductor voltage

At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.

vL(t) = Vs·e−t/τ = 20·e−10/4.533 = 2.203 V

Answer

vL = 2.203 V
12.RC & RL transients

Answer: i2 = 0.7255 mA

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial capacitor voltage

In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.

vC(0) = 24·3.3/(3.3 + 3.3) = 12 V

Time constant after the switch opens

τ = R2·C = 3.3·47 = 155.1 ms

Discharge

vC(t) = 12·e−250/155.1 = 2.394 V
i2 = vC/R2 = 2.394/3.3 = 0.7255 mA

Answer

i2 = 0.7255 mA
13.Thévenin & Norton

Answer: Vth = 6.75 V

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 20 ΩR3​ = 4 ΩSHORTR2​12 ΩAabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 20·12/(20+12) = 7.5 Ω
Rth = (R1 ∥ R2) + R3 = 7.5 + 4 = 11.5 Ω
R1​ = 20 ΩR3​ = 4 Ω+−V1​18 VR2​12 ΩAab+−Vth​

Find Vth, the open-circuit voltage

With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.

Vth = V1·R2/(R1+R2) = 18·12/(20+12) = 6.75 V
14.Thévenin & Norton

Answer: IN = 4.286 A

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 20 ΩR3​ = 2 ΩSHORTR2​2 ΩAOPENBabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 20·2/(20+2) = 1.818 Ω
Rth = (R1 ∥ R2) + R3 = 1.818 + 2 = 3.818 Ω
R1​ = 20 ΩR3​ = 2 Ω+−V1​12 VR2​2 ΩAIs​4 ABab+−Vth​

Find Vth, the open-circuit voltage

With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.

VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 1.091 + 4·1.818 = 8.364 V
Vth = VB = VA + Is·R3 = 8.364 + 4·2 = 16.36 V
IN​4.286 ARth​3.818 Ωab

Norton equivalent

A Norton source is the same circuit seen as a current source in parallel with R_th. Its current is the short-circuit current at a–b.

IN = Vth/Rth = 16.36/3.818 = 4.286 A
15.Bode plots & margins

Answer: |H| = −20.07 dB

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Corner frequency

ωc = R/L = 470/0.1 = 4700 rad/s
fc = 748 Hz → f/fc = 7500/748 = 10.03

Gain

|H| = 1/√(1 + 10.03²) = 0.09924
20·log₁₀(0.09924) = −20.07 dB

Answer

|H| = −20.07 dB
16.Bode plots & margins

Answer: ω180 = 4.472 rad/s

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Phase crossover

(ω/4)·(ω/5) = 1 → ω180 = √(4·5) = 4.472 rad/s

Answer

ω180 = 4.472 rad/s

ExamProblems · examproblems.com/courses/circuit-analysis-2