Circuit Analysis 2: AC circuits: cram pack

Formula sheets, the key method steps for every topic and 16 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Complex numbers

Rectangular form
z = a + jb, j² = −1, z̄ = a − jb
Modulus and argument
|z| = √(a² + b²), tan θ = b/a (check the quadrant)
Polar and exponential form
z = r∠θ = r(cos θ + j sin θ) = r·ejθ
Division
z₁/z₂ = z₁z̄₂/|z₂|²
Product and quotient
r₁∠θ₁ · r₂∠θ₂ = r₁r₂∠(θ₁ + θ₂), r₁∠θ₁ / r₂∠θ₂ = (r₁/r₂)∠(θ₁ − θ₂)
De Moivre
(r∠θ)ⁿ = rⁿ∠nθ
n-th roots
zk = R1/n∠((φ + 360°·k)/n), k = 0 … n − 1
Quadratic with p² < 4q
z = −p/2 ± j√(q − p²/4)

Method

  1. Decide which form suits the operation: rectangular a + jb for adding and subtracting, polar r∠θ for multiplying, dividing, powers and roots.
  2. Multiply out with j² = −1; divide by multiplying the top and bottom by the conjugate of the denominator.
  3. Convert with r = √(a² + b²) and θ from a sketch of the point (check the quadrant), and back with a = r cos θ, b = r sin θ.
  4. For powers use De Moivre, (r∠θ)ⁿ = rⁿ∠nθ; for zⁿ = R∠φ list all n roots R1/n∠((φ + 360°k)/n).

AC impedance & phasors

Impedances
ZR = R, ZL = jωL, ZC = 1/(jωC)
Angular frequency
ω = 2πf
Magnitude and angle
|Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law
V = I·Z

Method

  1. Convert the frequency: ω = 2πf.
  2. Find each reactance: XL = ωL and XC = 1/(ωC).
  3. Add impedances like resistors, with Z = R + jX.
  4. Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

AC power & power factor

Real power
P = V·I·cos φ
Reactive power
Q = V·I·sin φ
Apparent power
S = V·I = √(P² + Q²)
Power factor
pf = cos φ = P/S
Correction capacitor
QC = P(tan φ1 − tan φ2), C = QC/(ωV²)

LC resonance, Q factor & bandwidth

Natural frequency
ω0 = 1/√(LC), f0 = 1/(2π√(LC))
Energy
W = ½CV0² = ½Cv² + ½Li²
Peak current
Imax = V0√(C/L)
Quality factor
Q = 2π·(energy stored)/(energy lost per cycle)
Series RLC
Q = (1/R)√(L/C), BW = R/(2πL)
Parallel RLC
Q = R√(C/L), BW = 1/(2πRC)
Bandwidth
BW = f2 − f1 = f0/Q, f0 = √(f1f2)
Half-power frequencies
f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q))
Tank with coil resistance r
RD = L/(C·r) = Q²·r
Decay of the amplitude
e−Rt/(2L)

Method

  1. Find the resonance frequency first: ω₀ = 1/√(LC) and f₀ = ω₀/(2π).
  2. Decide whether the circuit is series or parallel: series Q = (1/R)√(L/C), parallel Q = R√(C/L).
  3. Use BW = f₀/Q for the bandwidth, or the shortcuts R/(2πL) (series) and 1/(2πRC) (parallel).
  4. For energy questions, use that the total energy ½CV₀² stays constant in an ideal LC circuit and swings between C and L every quarter period.

Three-phase power

Y connection
VL = √3·Vph, IL = Iph
Δ connection
VL = Vph, IL = √3·Iph
Total real power
P = √3·VL·IL·cos φ = 3·Iph²·R
Apparent and reactive power
S = √3·VL·IL, Q = P·tan φ
Correction capacitors
QC = P(tan φ1 − tan φ2), C = QC/(3ωV²)
Voltage across each capacitor
Δ: VL Y: VL/√3
Motor input
Pin = Pout/η

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Thévenin & Norton

Thévenin voltage
Vth = Vopen circuit
Thévenin resistance
Rth: all sources off, seen from a–b
Norton current
IN = Vth/Rth
Load current
IL = Vth/(Rth + RL)
Maximum power transfer
RL = Rth, Pmax = Vth²/(4Rth)

Method

  1. Remove the load and mark the two terminals a and b.
  2. Find the open-circuit voltage between a and b: this is Vth.
  3. Switch off all independent sources and find the resistance seen from a–b: this is Rth.
  4. Put the load back on the equivalent circuit: Vth in series with Rth.
  5. For the Norton equivalent, convert: IN = Vth/Rth, with RN = Rth in parallel.

2Practice problems

1.Complex numbersMedium
ReIm22−2−244−4−4θz

Write z = 3 − j4 in exponential form r·ejθ. Give θ in radians, between −π and π.

z = 3 − j4
θ = rad
2.Complex numbersHard
ReIm11−1−122−2−2z₀z₁

The roots of zⁿ = w with n = 2 and w = 4∠−120° are zk = R1/n∠((φ + 360°·k)/n), k = 0, 1. Find the argument of z₀ in degrees, between −180° and 180°.

w = 4∠−120°n = 2k = 0
θ₀ = °
3.AC impedance & phasorsMedium
100 V200 HzR = 40 ΩL = 100 mHC = 10 µFI

A series RLC circuit is connected to a 100 V (rms), 200 Hz supply. Find the power factor cos φ of the circuit.

V = 100 V (rms)f = 200 HzR = 40 ΩL = 100 mHC = 10 µF
cos φ =
4.AC impedance & phasorsHard
12 Vf0​R = 10 ΩL = 20 mHC = 4.7 µF

A series RLC circuit is driven by a 12 V (rms) source whose frequency is set to the resonant frequency of the circuit. Find the rms voltage VL across the inductor.

V = 12 V (rms)R = 10 ΩL = 20 mHC = 4.7 µF
VL = V
5.AC power & power factorMedium
P = 12 kWQ = ?Sφ

A single-phase motor takes 12 kW at a power factor of 0.9 lagging from a 240 V supply. Find the reactive power Q it draws.

P = 12 kWpf = 0.9V = 240 V
Q = kvar
6.AC power & power factorHard
P1​ = 3 kWQ1​S1​φ

A 10 kVA single-phase transformer supplies a load of 3 kW at a power factor of 0.7 lagging. How much extra real power ΔP can be added as a resistive (unity power factor) load before the transformer reaches its kVA rating?

Smax = 10 kVAP1 = 3 kWpf1 = 0.7
ΔP = kW
7.LC resonance, Q factor & bandwidthMedium
C = 220 nF+−9 VL = 0.47 µHiL​

A 220 nF capacitor charged to 12 V oscillates with an ideal 0.47 µH inductor. Find the energy WL stored in the inductor at the moment the capacitor voltage is 9 V, in µJ.

C = 220 nFV0 = 12 VvC = 9 V
WL = µJ
8.LC resonance, Q factor & bandwidthHard
V20 ΩLC = ?

Design a series RLC filter with a total resistance of 20 Ω, a resonance frequency of 50 kHz and a bandwidth of 1 kHz. Find the capacitance C in nF.

R = 20 Ωf0 = 50 kHzBW = 1 kHz
C = nF
9.Three-phase powerMedium
ABCVL​ = 400 VIL​ = ?M45 kW, η = 88%cos φ = 0.86

A three-phase induction motor delivers 45 kW of mechanical output power at full load. At this load its efficiency is 88% and its power factor is 0.86 lagging. The supply has a line-to-line voltage of 400 V. Find the line current IL.

Pout = 45 kWη = 88%cos φ = 0.86VL = 400 V
IL = A
10.Three-phase powerHard
P = 300 kWφ1​S1​Q2​QC​

A balanced three-phase load takes 300 kW at a power factor of 0.72 lagging from a 480 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.95 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.

P = 300 kWpf1 = 0.72pf2 = 0.95VL = 480 Vf = 50 Hz
Cph = µF
11.RC & RL transientsMedium
+−Vs​20 Vt = 0R1​ = 10 kΩR2​ = 6.8 kΩC33 µF+−vC​

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the capacitor voltage vC at t = 100 ms.

Vs = 20 VR1 = 10 kΩR2 = 6.8 kΩC = 33 µFt = 100 ms
vC = V
12.RC & RL transientsHard
+−Vs​15 Vt = 0R = 2.2 kΩC220 µF+−vC​vC​(0) = 12 V

Just before the switch closes at t = 0, the capacitor holds 12 V with the polarity shown. How long does it take for vC to reach 14.4 V? Find t.

Vs = 15 VR = 2.2 kΩC = 220 µFvC(0) = 12 V
t = ms
13.Thévenin & NortonMedium
R1​ = 15 ΩR3​ = 4 Ω+−V1​12 VR2​2 ΩAab

Find the Thévenin resistance Rth seen from terminals a–b.

V1 = 12 VR1 = 15 ΩR2 = 2 ΩR3 = 4 Ω
Rth = Ω
14.Thévenin & NortonHard
R1​ = 3 ΩR3​ = 25 Ω+−V1​18 VR2​15 ΩAIs​1.5 ABRL​5 ΩIL​

A load RL = 5 Ω is connected across a–b. Replace the rest of the circuit with its Thévenin equivalent and find the load current IL.

V1 = 18 VIs = 1.5 AR1 = 3 ΩR2 = 15 ΩR3 = 25 ΩRL = 5 Ω
IL = A
15.Bode plots & marginsMedium
vin​L = 20 mHC = 0.1 µFR = 100 Ωvout​

In the series RLC band-pass filter shown the output is taken across R = 100 Ω, with L = 20 mH and C = 0.1 µF. Find the centre (resonant) frequency f0 in Hz.

R = 100 ΩL = 20 mHC = 0.1 µF
f0 = Hz
16.Bode plots & marginsHard
|H| (dB)0.10.1111010100100−80−60−40−2002040ω (rad/s)φ (°)ω (rad/s)−270−180−900ω180​ = ?

A unity-feedback loop has the open-loop transfer function L(s) = 56/(s(s + 1)(s + 10)). Find the phase crossover frequency ω180, where ∠L(jω) = −180°.

L(s) = 56/(s(s + 1)(s + 10))
ω180 = rad/s

3Solutions

1.Complex numbers

Answer: θ = −0.9273 rad

Polar form: z = r∠θ = r(cos θ + j sin θ) = r·ejθ, with r = |z| and θ = arg z. Back to rectangular form: a = r cos θ, b = r sin θ. The argument needs the quadrant: θ = atan(b/a) only when a > 0; for a < 0 add or subtract 180°. In polar form multiplication is easy: multiply the moduli and add the arguments; for division divide the moduli and subtract the arguments.

Modulus

r = √(9 + 16) = 5

Argument in radians

θ = −53.13° = −53.13·π/180 = −0.9273 rad

Exponential form

z = 5·e−j0.9273

Answer

θ = −0.9273 rad
2.Complex numbers

Answer: θ₀ = −60 °

De Moivre and roots: (r∠θ)ⁿ = rⁿ∠nθ. The equation zⁿ = R∠φ has exactly n roots, all with modulus R1/n, at the arguments (φ + 360°·k)/n for k = 0, 1, …, n − 1: they lie evenly spaced on a circle, 360°/n apart. A quadratic z² + pz + q = 0 with p² < 4q has the complex roots z = −p/2 ± j√(q − p²/4); a polynomial with real coefficients always has its complex roots in conjugate pairs a ± jb.

Modulus of the roots

41/2 = 2

Argument of the root

θ₀ = (−120° + 360°·0)/2 = −60°

Argument

θ₀ = −60°

Answer

θ₀ = −60°

The 2 roots lie on the circle of radius 2, 180° apart.

3.AC impedance & phasors

Answer: cos φ = 0.6555

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

XL = 125.7 Ω, XC = 79.58 Ω

Impedance

|Z| = √(40² + (46.09)²) = 61.02 Ω

Power factor

cos φ = R/|Z| = 40/61.02 = 0.6555
The circuit is inductive, so the power factor is lagging.

Answer

cos φ = 0.6555
4.AC impedance & phasors

Answer: VL = 78.28 V

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance

At resonance the reactances cancel, so the impedance is just R.

ω₀ = 1/√(LC) = 1/√(0.02·4.7·10⁻⁶) = 3262 rad/s
I = V/R = 12/10 = 1.2 A

Voltage across the inductor

XL = ω₀L = 3262·0.02 = 65.23 Ω
VL = I·XL = 1.2·65.23 = 78.28 V

Answer

VL = 78.28 V

This is Q = 6.523 times the supply voltage.

5.AC power & power factor

Answer: Q = 5.812 kvar

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Angle

φ = arccos(0.9) = 25.84°, tan φ = 0.4843

Reactive power

Q = P·tan φ = 12·0.4843 = 5.812 kvar

Answer

Q = 5.812 kvar
6.AC power & power factor

Answer: ΔP = 6.52 kW

AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.

Reactive power of the existing load

Q1 = 3·tan(arccos 0.7) = 3.061 kvar

Largest total real power

At full rating S = Smax, and Q is unchanged by the resistive load.

P = √(Smax² − Q1²) = √(10² − 3.061²) = 9.52 kW

Extra real power

ΔP = 9.52 − 3 = 6.52 kW

Answer

ΔP = 6.52 kW
7.LC resonance, Q factor & bandwidth

Answer: WL = 6.93 µJ

LC resonance: a charged capacitor connected to an inductor drives a current that charges it the other way: the energy swings between the electric field of C (½Cv²) and the magnetic field of L (½Li²) at the natural frequency f0 = 1/(2π√(LC)). Without resistance the total energy ½CV0² stays constant, so the peak current is Imax = V0√(C/L). One period is T = 1/f0; the energy moves from C to L in a quarter of it.

Total energy

½·2.2 × 10⁻⁷·12² = 1.584 × 10⁻⁵ J

Energy left in the capacitor

½·2.2 × 10⁻⁷·9² = 8.91 × 10⁻⁶ J

Energy in the inductor

WL = 6.93 × 10⁻⁶ J = 6.93 µJ

Answer

WL = 6.93 µJ
8.LC resonance, Q factor & bandwidth

Answer: C = 3.183 nF

Q factor and bandwidth: in a resonant circuit Q = 2π·(energy stored)/(energy lost per cycle). For series RLC Q = ω0L/R = (1/R)√(L/C); for parallel RLC Q = R/(ω0L) = R√(C/L). The bandwidth between the half-power frequencies f1 and f2 (where the power is half and the current or voltage 1/√2 of its peak) is BW = f2 − f1 = f0/Q, which is R/(2πL) in series and 1/(2πRC) in parallel. The resonance frequency is the geometric mean f0 = √(f1f2), and f1,2 = f0(√(1 + 1/(4Q²)) ∓ 1/(2Q)). Losses also make the oscillation decay: in series RLC the amplitude falls as e−Rt/(2L).

Inductance from the bandwidth

L = R/(2π·BW) = 20/(2π·1000) = 0.003183 H

Capacitance from the resonance frequency

C = 1/((2π·50000)²·0.003183) = 3.183 × 10⁻⁹ F = 3.183 nF

Answer

C = 3.183 nF

Q = f₀/BW = 50.

9.Three-phase power

Answer: IL = 85.82 A

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.

Electrical input power

Pin = Pout/η = 45/0.88 = 51.14 kW

Line current

IL = Pin/(√3·VL·cos φ) = 51136/(√3·400·0.86) = 85.82 A

Answer

IL = 85.82 A
10.Three-phase power

Answer: Cph = 2633 µF

Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.

Reactive power before and after

The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.

Q1 = 300·tan(acos 0.72) = 300·0.9639 = 289.2 kvar
Q2 = 300·tan(acos 0.95) = 300·0.3287 = 98.61 kvar

Reactive power from the capacitors

QC = Q1 − Q2 = 190.6 kvar

Capacitance per phase

In a Y bank each capacitor is connected between a line and the star point.

V = 480/√3 = 277.1 V, ω = 2π·50 = 314.2 rad/s
Cph = (QC/3)/(ω·V²) = 63517/(314.2·277.1²) = 2633 µF

Answer

Cph = 2633 µF
11.RC & RL transients

Answer: vC = 4.266 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find Rth; open the capacitor to find the voltage it will settle at.

Rth = R1 ∥ R2 = 10·6.8/(10 + 6.8) = 4.048 kΩ
vC(∞) = 20·6.8/(10 + 6.8) = 8.095 V

Time constant

τ = Rth·C = 4.048·33 = 133.6 ms

Charging curve

vC(t) = 8.095·(1 − e−100/133.6) = 4.266 V

Answer

vC = 4.266 V
12.RC & RL transients

Answer: t = 779 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 12 V, vC(∞) = Vs = 15 V
τ = R·C = 2.2 kΩ · 220 µF = 484 ms
vC(t) = 15 + (12 − 15)·e−t/τ

Solve for the time

14.4 = 15 + (−3)·e−t/τ → e−t/τ = (14.4 − 15)/(12 − 15) = 0.2
t = τ·ln((12 − 15)/(14.4 − 15)) = 484·ln(5) = 779 ms

Answer

t = 779 ms
13.Thévenin & Norton

Answer: Rth = 5.765 Ω

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 15 ΩR3​ = 4 ΩSHORTR2​2 ΩAabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 15·2/(15+2) = 1.765 Ω
Rth = (R1 ∥ R2) + R3 = 1.765 + 4 = 5.765 Ω
14.Thévenin & Norton

Answer: IL = 1.731 A

Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.

R1​ = 3 ΩR3​ = 25 ΩSHORTR2​15 ΩAOPENBabRth​

Find Rth with every source switched off

Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.

R1 ∥ R2 = 3·15/(3+15) = 2.5 Ω
Rth = (R1 ∥ R2) + R3 = 2.5 + 25 = 27.5 Ω
R1​ = 3 ΩR3​ = 25 Ω+−V1​18 VR2​15 ΩAIs​1.5 ABab+−Vth​

Find Vth, the open-circuit voltage

With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.

VA = V1·R2/(R1+R2) + Is·(R1∥R2) = 15 + 1.5·2.5 = 18.75 V
Vth = VB = VA + Is·R3 = 18.75 + 1.5·25 = 56.25 V
Rth​ = 27.5 Ω+−Vth​56.25 VRL​5 ΩIL​

Connect the load to the Thévenin equivalent

The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.

IL = Vth/(Rth + RL) = 56.25/(27.5 + 5) = 1.731 A
15.Bode plots & margins

Answer: f0 = 3559 Hz

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Resonant frequency

ω₀ = 1/√(LC) = 1/√(0.02·1 × 10⁻⁷) = 22361 rad/s
f₀ = ω₀/(2π) = 3559 Hz

Answer

f0 = 3559 Hz
16.Bode plots & margins

Answer: ω180 = 3.162 rad/s

Frequency response: substitute s = jω in the transfer function. The magnitude in decibels is 20·log₁₀|H(jω)| and the phase is the sum of the angles of the numerator factors minus those of the denominator factors. A first-order RC or RL filter has its corner (−3 dB) frequency at ωc = 1/(RC) or R/L, and fc = ωc/(2π); a low-pass filter gives |H| = 1/√(1 + (ω/ωc)²) and φ = −atan(ω/ωc). In the asymptotic (straight-line) Bode plot each pole bends the magnitude down by 20 dB/decade at its corner frequency, each zero bends it up by 20 dB/decade, and an integrator 1/s gives −20 dB/decade at all frequencies. Gain crossover ωc: |L(jω)| = 1 (0 dB); phase margin PM = 180° + ∠L(jωc). Phase crossover ω180: ∠L(jω) = −180°; gain margin GM = −20·log₁₀|L(jω180)| dB. The closed loop is stable when both margins are positive.

Phase crossover

(ω/1)·(ω/10) = 1 → ω180 = √(1·10) = 3.162 rad/s

Answer

ω180 = 3.162 rad/s

ExamProblems · examproblems.com/courses/circuit-analysis-2