Number systems
- Place values
- binary 2k, octal 8k, hex 16k
- To decimal
- Σ dk·bk
- From decimal
- divide by the base, read the remainders bottom-up
- Hex ↔ binary
- one hex digit = 4 bits
- Two’s complement
- invert the bits and add 1
Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
The 8-bit pattern 1101 0000 stores a signed integer in two's complement. What is its value N in decimal?
A system must give every one of 1955 items its own binary code of the same length. What is the smallest number of bits b needed?
A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = 0, I₁ = 0, I₂ = 1, I₃ = C. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.
A Johnson (twisted-ring) counter is made of 4 D flip-flops, with the inverted last output fed back to the first input, and starts at all zeros. How many different states N does it go through?
A UART sends bytes at 9600 baud in the format 8E2: 8 data bits, an even parity bit and 2 stop bit(s), plus the start bit. Find the largest number of data bytes per second it can transfer.
A 2.4 kHz square wave is sampled at 10 kHz with no anti-aliasing filter. A square wave contains the odd harmonics 3f₁, 5f₁, 7f₁, … At which frequency fa does its harmonic 7f₁ appear in the sampled data? Give it in kHz.
Answer: N = −48
Positional number systems: each digit is worth its value times a power of the base. In binary the places are worth 1, 2, 4, 8, 16, …; in hexadecimal 1, 16, 256, …, with A–F standing for 10–15. In 8-bit two's complement the leftmost bit is worth −128 instead of +128, which is how negative numbers are stored.
The other bits keep their normal positive values.
Answer: b = 11 bit
Positional number systems: each digit is worth its value times a power of the base. In binary the places are worth 1, 2, 4, 8, 16, …; in hexadecimal 1, 16, 256, …, with A–F standing for 10–15. In 8-bit two's complement the leftmost bit is worth −128 instead of +128, which is how negative numbers are stored.
Answer: N = 3
Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.
Answer: N = 8
Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.
Answer: RB = 800 B/s
UART: an asynchronous serial link sends each byte as a frame: one start bit (low), the data bits, an optional parity bit and one or two stop bits (high). The baud rate is the number of bits per second, so one bit lasts Tb = 1/baud and a frame of n bits lasts n/baud. The common 8N1 format has 10 bits per byte. The baud generator divides the clock: baud = fclk/(16·D) with a whole number D, so the real baud rate differs slightly from the target; an error below about 2 % is usually acceptable.
Answer: fa = 3.2 kHz
Sampling: an ADC measures the signal fs times per second. By the Nyquist–Shannon theorem a frequency f is captured correctly only while f < fs/2, the Nyquist (folding) frequency, so the sampling rate must exceed twice the highest signal frequency. A higher frequency is not lost: it shows up as an alias at fa = |f − k·fs|, with the whole number k that brings the result between 0 and fs/2. The samples cannot tell the two apart, so an analogue anti-aliasing filter must remove everything above fs/2 before the ADC.
The alias lands inside the signal band, where no digital filter can remove it. Only an analogue filter before the ADC helps.
ExamProblems · examproblems.com/courses/digital-electronics