Number systems
- Place values
- binary 2k, octal 8k, hex 16k
- To decimal
- Σ dk·bk
- From decimal
- divide by the base, read the remainders bottom-up
- Hex ↔ binary
- one hex digit = 4 bits
- Two’s complement
- invert the bits and add 1
Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
Set the bits so they store −40 in 8-bit two's complement. Read as an unsigned number, what is the pattern's value U?
Set the bits to the 8-bit result of 1011 0001 OR 1111 0100. What is the result's value R in decimal?
A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = C, I₁ = 1, I₂ = C′, I₃ = 0. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.
A positive-edge-triggered T flip-flop starts with Q = 0 and receives the inputs shown. Click the first clock edge at which Q goes from 1 back to 0.
A UART sends bytes at 2400 baud in the format 8E1: 8 data bits, an even parity bit and 1 stop bit(s), plus the start bit. Find the largest number of data bytes per second it can transfer.
A 600 Hz square wave is sampled at 2 kHz with no anti-aliasing filter. A square wave contains the odd harmonics 3f₁, 5f₁, 7f₁, … At which frequency fa does its harmonic 3f₁ appear in the sampled data? Give it in Hz.
Answer: U = 216
Setting bits: each bit is worth a power of two (128, 64, …, 1). One hex digit is exactly four bits, and in 8-bit two's complement the leftmost bit is worth −128. Bitwise operations work on each bit position separately.
Answer: R = 245
Setting bits: each bit is worth a power of two (128, 64, …, 1). One hex digit is exactly four bits, and in 8-bit two's complement the leftmost bit is worth −128. Bitwise operations work on each bit position separately.
OR gives 1 where at least one bit is 1.
Answer: N = 4
Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.
Answer: clock edge 4
Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.
A T flip-flop toggles at each rising edge with T = 1 and holds with T = 0.
Answer: RB = 218.2 B/s
UART: an asynchronous serial link sends each byte as a frame: one start bit (low), the data bits, an optional parity bit and one or two stop bits (high). The baud rate is the number of bits per second, so one bit lasts Tb = 1/baud and a frame of n bits lasts n/baud. The common 8N1 format has 10 bits per byte. The baud generator divides the clock: baud = fclk/(16·D) with a whole number D, so the real baud rate differs slightly from the target; an error below about 2 % is usually acceptable.
Answer: fa = 200 Hz
Sampling: an ADC measures the signal fs times per second. By the Nyquist–Shannon theorem a frequency f is captured correctly only while f < fs/2, the Nyquist (folding) frequency, so the sampling rate must exceed twice the highest signal frequency. A higher frequency is not lost: it shows up as an alias at fa = |f − k·fs|, with the whole number k that brings the result between 0 and fs/2. The samples cannot tell the two apart, so an analogue anti-aliasing filter must remove everything above fs/2 before the ADC.
The alias lands inside the signal band, where no digital filter can remove it. Only an analogue filter before the ADC helps.
ExamProblems · examproblems.com/courses/digital-electronics