Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 200 km/h to take off and the usable runway is 1200 m long. Starting from rest, what constant acceleration a does it need?
A ball is thrown straight up at 6 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
A 6 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
An 8.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is kicked from level ground at 32 m/s and 50° above the horizontal towards a wall 62 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
A ball is launched at 45° above horizontal from the top of a 55 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A car takes a flat curve of radius 85 m. The coefficient of static friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.2 kg ball on a string 1.4 m long is swung in a vertical circle. At the lowest point it moves at 4 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A toy launcher has a vertical spring of stiffness 500 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 8 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
A 2.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.25) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 6 kg projectile moving horizontally at 23 m/s explodes into two fragments that move along the same line. The 4 kg fragment continues forwards at 80 m/s. Find the velocity v′2 of the 2 kg fragment (positive in the original direction).
A 0.45 kg ball hits a wall at 17 m/s and bounces straight back at 11 m/s. The contact lasts 25 ms. Find the magnitude of the impulse J the wall gives the ball.
A uniform slender rod of mass 6 kg and length 1.7 m is pinned at one end and released from rest in a horizontal position. Ignore friction and use g = 9.81 m/s². Find the speed v of the free end as the rod swings through the vertical position.
A hollow sphere rolls without slipping down a slope inclined at 15° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 7.5 m down the slope?
A 15 kW motor running at 2900 rpm drives a pinion with 30 teeth and a module of 2.5 mm. Find the tangential force Ft on the pinion teeth.
An open belt connects an 80 mm pulley and a 400 mm pulley whose centres are 1200 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A simple pendulum has a length of 1.5 m. Use g = 9.81 m/s². Find its period T for small swings.
A 1.3 kg mass on a spring with k = 40 N/m is pulled 14 cm from equilibrium and released. Find the total energy E of the oscillation.
A 15 kg mass on a spring with a stiffness of 5 kN/m has a viscous damper giving a damping ratio of 0.7. Find the damped natural frequency fd of its free vibration in Hz.
A 100 kg mass hangs from spring k₃ = 50 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 100 kN/m and k₂ = 30 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: a = 1.286 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 6.835 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 1.479 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: a = 2.365 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: y = 29.32 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The ball is already on its way down at the wall.
Answer: x = 53.12 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 20.42 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 25.49 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: h = 1.087 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: x = 55.37 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′2 = −91 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The minus sign means the second fragment flies backwards.
Answer: J = 12.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 7.073 m/s
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: t = 3.138 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: Ft = 1317 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: θ = 164.7 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: T = 2.457 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 0.392 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 2.075 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 3.024 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics