Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 250 km/h to take off and the usable runway is 2200 m long. Starting from rest, what constant acceleration a does it need?
A ball is thrown straight up at 16 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
Masses of 8 kg and 4 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 40 m/s and must land 125 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 29 m/s and 45° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
A car takes a flat curve of radius 145 m. The coefficient of static friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.3 kg ball on a string 1.4 m long is swung in a vertical circle. At the lowest point it moves at 5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 14 m along the slope.
A 5 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 6 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 0.5 m.
A 20 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 22 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 0.25 kg ball hits a wall at 29 m/s and bounces straight back at 7 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
A uniform slender rod of mass 8.5 kg and length 0.9 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find its angular acceleration α just after release.
A hollow sphere of mass 13.5 kg rolls without slipping at 4.5 m/s. Find its rotational kinetic energy Erot.
Two parallel shafts are 112.5 mm apart. They must be connected by a pair of spur gears with a module of 3 mm and a speed reduction of 1.5 : 1. How many teeth N1 must the pinion have?
In a compound gear train, gear A (20 teeth) on the input shaft turning at 960 rpm drives gear B (80 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (72 teeth) on the output shaft. Find the output speed nout.
How long must a simple pendulum be to have a period of 1 s? Use g = 9.81 m/s². Find L.
A 10 g bullet moving at 400 m/s hits and stays in a 1.5 kg block resting on a frictionless surface. The block is attached to a horizontal spring with k = 1400 N/m. Find the amplitude A of the resulting oscillation in cm.
A 5 kg mass is supported by a spring with a stiffness of 1 kN/m and a viscous damper with a damping coefficient of 70 N·s/m. Find the damping ratio ζ.
A 40 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 5 kN/m and k₂ = 50 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: a = 1.096 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 3.799 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive and the ground is h₀ below the starting point.
Only the positive root is physical.
Answer: T = 52.32 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: T = 15.42 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: θ = 25.02 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 64.98°.
Answer: α = 62.84 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Energy or v² = v₀² + 2as in the vertical direction.
Answer: vmax = 33.73 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 35.97 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: v = 11.24 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 2.164 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 106 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: J = 9 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: α = 16.35 rad/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
Answer: Erot = 91.13 J
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N1 = 30
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nout = 40 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 24 : 1
Answer: L = 0.2485 m
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: A = 8.7 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.495
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: keq = 55 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics