Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 108 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. How long does braking take? Find t.
A tram starts from rest and accelerates at 1 m/s² for 10 s, then runs at constant speed for 18 s, and finally brakes at 3.5 m/s² until it stops. Find the total travel time t.
A 9 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A ball is launched at 45° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A small ball on a string of length 1.8 m moves in a horizontal circle so that the string makes a constant angle of 60° with the vertical (a conical pendulum). Use g = 9.81 m/s². Find the speed v of the ball.
A 0.8 kg ball on a light string 1.2 m long is swung in a vertical circle. At the lowest point its speed is 11 m/s. Ignore air resistance and use g = 9.81 m/s². Find the tension Ttop in the string at the highest point.
A 1 kg ball hangs on a light string of length 0.8 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
A 2 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 25 N parallel to the slope. The coefficient of kinetic friction is 0.2. Find the speed v of the block after it has moved 10 m up the slope.
A 3.5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
A 0.6 kg ball hits a wall at 22 m/s and bounces straight back at 9 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
A 1 kg block hangs from a light cord wrapped around a pulley, a uniform solid disc of mass 14.5 kg and radius 0.45 m that turns on a frictionless horizontal axle. The block is released from rest. Use g = 9.81 m/s². Find the angular acceleration α of the pulley.
A solid cylinder starts from rest and rolls without slipping down a slope inclined at 20° to the horizontal. Use g = 9.81 m/s². Its radius is 0.2 m. Find its angular velocity ω after it has rolled 2 m along the slope.
A belt runs on an 80 mm driving pulley at 1440 rpm. The tension is 600 N on the tight side and 300 N on the slack side. Find the power P transmitted, in kW.
In a compound gear train, gear A (12 teeth) on the input shaft turns at 1440 rpm and drives gear B (15 teeth). Gear C (16 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 460.8 rpm. How many teeth ND must gear D have?
A 4 kg mass on a spring with k = 90 N/m is pulled 8 cm in the positive direction and released from rest at t = 0. Find its displacement x from equilibrium at t = 1.2 s (with sign).
A 0.6 kg mass is attached to the lower end of an unstretched vertical spring with k = 320 N/m and released from rest. Use g = 9.81 m/s². Find the greatest extension xmax of the spring in cm.
In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 2 cycles later by a peak of 4.7 mm. Find the damping ratio ζ.
A 100 kg mass hangs from spring k₃ = 12 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 20 kN/m and k₂ = 80 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 4.615 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 30.86 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 3.216 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 17.66 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: t = 4.21 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: x = 131.5 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: v = 5.147 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Tension and gravity together give the inward force: tan θ = v²/(r·g).
Answer: Ttop = 41.43 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Kinetic energy is traded for potential energy over a height 2r.
Tension and gravity both point down, towards the centre.
Answer: T = 16.82 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Check: T = mg(3 − 2cos θ) = 16.82 N.
Answer: v = 10.26 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v′2 = 10.27 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: J = 18.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: α = 2.642 rad/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: ω = 14.96 rad/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Rolling without slipping: ω = v/r, and friction does no work at the contact point.
Answer: P = 1.81 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: ND = 40
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: x = 6.643 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: xmax = 3.679 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.05997
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 1.647 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics