Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 120 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. How long does braking take? Find t.
Ball A is dropped from rest from a height of 50 m. At the same instant ball B is thrown straight up from the ground directly below at 20 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
A 20 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 4 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A ball is launched at 18 m/s and 30° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
In a fairground rotor, riders stand against the wall of a vertical cylinder of radius 3.5 m. When it spins fast enough the floor drops away and friction holds them up. The coefficient of static friction is 0.5. Use g = 9.81 m/s². Find the smallest rotation rate n in revolutions per minute.
A 0.6 kg ball on a string 1 m long is swung in a vertical circle. At the lowest point it moves at 6 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A car travelling at 60 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
A 0.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.2) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 4 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
A 0.25 kg ball hits a wall at 15 m/s and bounces straight back at 12 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
A uniform slender rod of mass 16.5 kg and length 1.6 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find the acceleration atip of the free end just after release.
A hollow sphere of mass 12.5 kg rolls without slipping at 4 m/s. Find its total kinetic energy Ek.
Two parallel shafts are 140 mm apart. They must be connected by a pair of spur gears with a module of 5 mm and a speed reduction of 2.5 : 1. How many teeth N1 must the pinion have?
An open belt connects a 160 mm driving pulley at 1500 rpm to a 250 mm pulley; the centres are 1200 mm apart. The coefficient of friction is 0.35 and the tight-side tension may not exceed 1000 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).
A 2 kg mass on a spring with k = 230 N/m is pulled 5 cm in the positive direction and released from rest at t = 0. Find its displacement x from equilibrium at t = 0.7 s (with sign).
A 1.6 kg mass on a spring with k = 470 N/m is pulled 9 cm from equilibrium and released. Find its maximum acceleration amax.
A 25 kg mass on a spring with a stiffness of 10 kN/m has a viscous damper giving a damping ratio of 0.3. Find the damped natural frequency fd of its free vibration in Hz.
A 10 kg mass hangs from spring k₃ = 25 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 30 kN/m and k₂ = 20 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 9.524 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 2.5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: a = 2.368 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: a = 1.962 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: t = 2.806 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: H = 44.13 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: n = 22.61 rpm
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 27.49 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: d = 17.7 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Doubling the speed makes the stopping distance four times longer.
Answer: x = 15.76 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′1 = −0.2222 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
The minus sign means the first glider bounces back.
Answer: Favg = 1350 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: atip = 14.71 m/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
atip = 1.5·g for any length: the free end falls faster than a dropped stone.
Answer: Ek = 166.7 J
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N1 = 16
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: P = 8.27 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: x = 1.702 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: amax = 26.44 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 3.036 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 6.497 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics