Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 60 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. How long does braking take? Find t.
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 20 m/s² for 2.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
A 20 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 4 m/s. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
A ball is launched from level ground at 38 m/s and must land 75 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 25° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A curve of radius 220 m is banked at 25°. At what speed v can a car take it with no friction needed at all? Use g = 9.81 m/s².
A 1.3 kg ball on a string 1.5 m long is swung in a vertical circle. At the lowest point it moves at 6.5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A car travelling at 60 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
A 2 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 20 N parallel to the slope. The coefficient of kinetic friction is 0.3. Find the speed v of the block after it has moved 7 m up the slope.
A 1400 kg car moving at 13 m/s runs into a stationary 2000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
A 0.25 kg ball hits a wall at 12 m/s and bounces straight back at 19 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
A shaft transmits 41.5 kW at 2900 rpm. Find the torque T in the shaft.
A uniform slender rod of mass 9 kg and length 0.6 m hangs at rest from a frictionless pivot at its top end. A 35 g bullet moving horizontally at 340 m/s hits the rod 0.24 m below the pivot and stays embedded. Use g = 9.81 m/s². Find the largest angle φ from the vertical through which the rod swings.
A 1.5 kW motor running at 1500 rpm drives a pinion with 15 teeth, which meshes with a gear with 40 teeth. The gear pair has an efficiency of 95%. Find the output torque T2 on the gear shaft.
In a compound gear train, gear A (50 teeth) on the input shaft turning at 960 rpm drives gear B (80 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (80 teeth) on the output shaft. Find the output speed nout.
A simple pendulum has a length of 2.1 m. Use g = 9.81 m/s². Find its period T for small swings.
A 1 kg mass is attached to the lower end of an unstretched vertical spring with k = 250 N/m and released from rest. Use g = 9.81 m/s². Find the greatest speed vmax of the mass.
A 100 kg mass on a spring with a stiffness of 20 kN/m has a viscous damper giving a damping ratio of 0.35. Find the damped natural frequency fd of its free vibration in Hz.
A 40 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 25 kN/m and k₂ = 30 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: t = 3.03 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 189.9 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
At the top the velocity is zero.
Answer: a = 5.896 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: d = 1.256 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Both forces point down the slope; the mass cancels.
Answer: θ = 15.32 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 74.68°.
Answer: x = 28.43 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: v = 31.72 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 49.37 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: d = 35.39 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Doubling the speed makes the stopping distance four times longer.
Answer: v = 5.242 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: ΔK = 69588 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The lost energy goes into deformation, heat and sound.
Answer: Favg = 310 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: T = 136.7 N·m
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: φ = 30.89 °
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
The pivot force passes through the pivot, so it has no moment there during the impact.
Answer: T2 = 24.19 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 90 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 10.67 : 1
Answer: T = 2.907 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.6204 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
The speed is largest at equilibrium.
Answer: fd = 2.108 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 55 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics