Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 36 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. How long does braking take? Find t.
Ball A is dropped from rest from a height of 20 m. At the same instant ball B is thrown straight up from the ground directly below at 21 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
Masses of 6.5 kg and 5.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
A 7.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
A ball is launched at 20° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A car takes a flat curve of radius 90 m. The coefficient of static friction between tyres and road is 0.3. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A curve of radius 210 m is banked at 25°, and the coefficient of static friction between tyres and road is 0.15. Use g = 9.81 m/s². Find the highest speed vmax at which a car can take the curve without sliding up and out.
A 2 kg block slides 11 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
A 1 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.3) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 3 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
A 10 g bullet is fired horizontally into a 2.5 kg block hanging from light strings 0.9 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A motor brings a flywheel with a moment of inertia of 15.5 kg·m² from rest up to 2500 rpm in 16 s. Ignoring losses, find the average power Pavg it delivers, in kW.
A solid cylinder rolls without slipping down a slope inclined at 35° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 3 m down the slope?
A 2.2 kW motor running at 1440 rpm drives a pinion with 30 teeth and a module of 2 mm. Find the tangential force Ft on the pinion teeth.
In a compound gear train, gear A (15 teeth) on the input shaft turning at 2900 rpm drives gear B (16 teeth). Gear C (15 teeth) is fixed to the same shaft as B and drives gear D (36 teeth) on the output shaft. Find the output speed nout.
A simple pendulum has a length of 0.7 m. Use g = 9.81 m/s². Find its period T for small swings.
A 2.1 kg mass on a spring with k = 120 N/m is pulled 19 cm from equilibrium and released. Find its maximum acceleration amax.
In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 3 cycles later by a peak of 6.9 mm. Find the damping ratio ζ.
A 10 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 80 kN/m and k₂ = 12 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: t = 2.857 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 0.9524 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: T = 58.45 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: T = 26.28 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: H = 26.83 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
At the top the vertical velocity is zero: vy² = 2gH.
Answer: t = 3.516 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 16.27 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: vmax = 36.95 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Friction points down the slope.
Answer: Wf = 39.12 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: x = 12.79 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′2 = 1.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: v = 386.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: Pavg = 33.2 kW
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: t = 1.265 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: Ft = 486.3 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nout = 1133 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2.56 : 1
Answer: T = 1.678 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: amax = 10.86 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.01968
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 92 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics