Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 60 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 38 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
A 10 kg sled is pulled across level snow by a rope at 25° above the horizontal with a force of 30 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is launched from level ground at 40° above the horizontal and lands 15 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
A ball is launched at 40° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A car takes a flat curve of radius 65 m. The coefficient of static friction between tyres and road is 0.3. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.7 kg ball on a string 1 m long is swung in a vertical circle. At the lowest point it moves at 7.5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A toy launcher has a vertical spring of stiffness 200 N/m. A 0.2 kg ball is placed on it and the spring is compressed by 8 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
A 5 kg cart is released from rest at a height of 5.2 m on a smooth track that leads into a vertical circular loop of radius 2 m. Find the speed v of the cart at the top of the loop.
A 5 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 24 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 0.55 kg ball hits a wall at 27 m/s and bounces straight back at 7 m/s. The contact lasts 25 ms. Find the magnitude of the impulse J the wall gives the ball.
A shaft transmits 7.5 kW at 2900 rpm. Find the torque T in the shaft.
A thin hoop starts from rest and rolls without slipping down a slope inclined at 15° to the horizontal. Use g = 9.81 m/s². Find its speed v after it has rolled 5.5 m along the slope.
Two parallel shafts are 63 mm apart. They must be connected by a pair of spur gears with a module of 2 mm and a speed reduction of 2.5 : 1. How many teeth N1 must the pinion have?
An open belt connects a 125 mm pulley and a 315 mm pulley whose centres are 500 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
An astronaut on another planet finds that a simple pendulum 0.7 m long has a period of 1.06 s for small swings. Find the gravitational acceleration g on that planet.
A 1.7 kg mass is attached to the lower end of an unstretched vertical spring with k = 210 N/m and released from rest. Use g = 9.81 m/s². Find the greatest speed vmax of the mass.
A 50 kg mass on a spring with a stiffness of 150 kN/m has a viscous damper giving a damping ratio of 0.7. Find the damped natural frequency fd of its free vibration in Hz.
A 5 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 40 kN/m and k₂ = 100 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 2.083 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 833.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
At the top the velocity is zero.
Answer: a = 1.01 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: a = 7.848 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: v0 = 12.22 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: t = 5.956 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 13.83 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 112.3 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: h = 0.3262 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 4.852 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
The cart just makes it round when h = 2.5R; then N = 0 at the top.
Answer: v = 436.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: J = 18.7 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: T = 24.7 N·m
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: v = 3.737 m/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Rolling without slipping: ω = v/r, and friction does no work at the contact point.
Answer: N1 = 18
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: θ = 158.1 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: g = 24.59 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.8826 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
The speed is largest at equilibrium.
Answer: fd = 6.225 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 26.63 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics