Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 54 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
A ball is thrown straight up at 11 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
A 4 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
A ball is thrown from ground level at 37 m/s and 50° above the horizontal. It lands on the flat roof of a building 12 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
A car takes a flat curve of radius 95 m. The coefficient of static friction between tyres and road is 0.3. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 0.4 kg ball on a light string 0.8 m long is swung in a vertical circle. At the lowest point its speed is 7.5 m/s. Ignore air resistance and use g = 9.81 m/s². Find the tension Ttop in the string at the highest point.
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 9 m along the slope.
A spring of stiffness 5000 N/m at the bottom of a 40° slope is compressed by 20 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 12 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 6 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 0.3 kg ball hits a wall at 16 m/s and bounces straight back at 6 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
A uniform slender rod of mass 4 kg and length 1 m is pinned at one end and released from rest in a horizontal position. Ignore friction and use g = 9.81 m/s². Find the speed v of the free end as the rod swings through the vertical position.
A uniform solid disc (mass 20 kg, radius 0.3 m) spins freely at 900 rpm about a vertical frictionless shaft. A thin ring of mass 8 kg and the same radius is dropped onto it from rest, centred on the shaft, and the two quickly spin together. Find their common speed n2 in rpm.
A 22 kW motor running at 1440 rpm drives a pinion with 25 teeth and a module of 4 mm. Find the tangential force Ft on the pinion teeth.
In a compound gear train, gear A (32 teeth) on the input shaft turns at 3000 rpm and drives gear B (36 teeth). Gear C (30 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 1000 rpm. How many teeth ND must gear D have?
A simple pendulum has a length of 0.8 m. Use g = 9.81 m/s². Find its period T for small swings.
A 0.5 kg mass on a spring with k = 250 N/m is pulled 13 cm from equilibrium and released. Find the total energy E of the oscillation.
A 200 kg mass is supported by a spring with a stiffness of 200 kN/m and a viscous damper with a damping coefficient of 1900 N·s/m. Find the damping ratio ζ.
A 5 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 25 kN/m and the lower one k₂ = 15 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: s = 14.06 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 41.17 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 3.618 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: a = 2.339 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: H = 72.01 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
At the top the vertical velocity is zero: vy² = 2gH.
Answer: x = 126.5 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Larger root: the ball is descending.
Answer: vmax = 16.72 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: Ttop = 8.505 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Kinetic energy is traded for potential energy over a height 2r.
Tension and gravity both point down, towards the centre.
Answer: v = 10.6 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: d = 2.561 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 91.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: J = 6.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 5.425 m/s
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: n2 = 500 rpm
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: Ft = 2918 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: ND = 80
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: T = 1.794 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 2.113 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.1502
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 6.892 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/dynamics