Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 100 km/h brakes with a constant deceleration of 6 m/s² until it stops. How long does braking take? Find t.
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 30 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
An 8 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
An 8 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 9 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 50° above the horizontal and lands 70 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
A ball is launched at 11 m/s and 45° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
A car takes a flat curve of radius 45 m. The coefficient of static friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.6 kg ball on a light string 0.5 m long is swung in a vertical circle. At the lowest point its speed is 9.5 m/s. Ignore air resistance and use g = 9.81 m/s². Find the tension Ttop in the string at the highest point.
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.3. Find its speed v after it has slid 7 m along the slope.
A 15 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 100 N parallel to the slope. The coefficient of kinetic friction is 0.15. Find the speed v of the block after it has moved 5 m up the slope.
A 15 kg projectile moving horizontally at 26 m/s explodes into two fragments that move along the same line. The 2 kg fragment continues forwards at 58 m/s. Find the velocity v′2 of the 13 kg fragment (positive in the original direction).
A 5 g bullet is fired horizontally into a 2.5 kg block hanging from light strings 0.5 m long, and stays in it. The strings swing out to a largest angle of 40° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A flywheel with a moment of inertia of 6.5 kg·m² spins at 2000 rpm. A brake applies a constant friction torque of 60 N·m. How many revolutions N does the flywheel make before it stops?
A hollow sphere of mass 9.5 kg rolls without slipping at 10 m/s. Find its rotational kinetic energy Erot.
A 5.5 kW motor running at 1500 rpm drives a pinion with 15 teeth, which meshes with a gear with 25 teeth. The gear pair has an efficiency of 96%. Find the torque T1 on the motor shaft.
In a compound gear train, gear A (16 teeth) on the input shaft turning at 1450 rpm drives gear B (60 teeth). Gear C (24 teeth) is fixed to the same shaft as B and drives gear D (40 teeth) on the output shaft. Find the output speed nout.
A simple pendulum has a length of 0.6 m. Use g = 9.81 m/s². Find its period T for small swings.
A 1.1 kg mass on a spring with k = 490 N/m is pulled 6 cm from equilibrium and released. Find its maximum acceleration amax.
An 8 kg mass on a spring with a stiffness of 150 kN/m has a viscous damper giving a damping ratio of 0.7. Find the damped natural frequency fd of its free vibration in Hz.
A 40 kg mass hangs from spring k₃ = 100 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 100 kN/m and k₂ = 25 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 4.63 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 547.8 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
At the top the velocity is zero.
Answer: a = 4.02 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 73.89 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: v0 = 26.41 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: H = 53.08 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: vmax = 14.86 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: Ttop = 210.3 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Kinetic energy is traded for potential energy over a height 2r.
Tension and gravity both point down, towards the centre.
Answer: v = 8.245 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 4.392 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v′2 = 21.08 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 759 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: N = 378.2 rev
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: Erot = 316.7 J
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: T1 = 35.01 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 232 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 6.25 : 1
Answer: T = 1.554 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: amax = 26.73 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 15.56 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 5.931 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics