Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 280 km/h to take off and the usable runway is 1100 m long. Starting from rest, what constant acceleration a does it need?
Ball A is dropped from rest from a height of 15 m. At the same instant ball B is thrown straight up from the ground directly below at 10 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
A 30 kg box is pushed up a ramp at 30° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the pushing force F.
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 145 N pulls the front 6 kg block; the 11 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A ball is launched at 21 m/s and 30° above the horizontal from the top of a 45 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
A car takes a flat curve of radius 90 m. The coefficient of static friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 0.8 kg ball on a string 1.4 m long is swung in a vertical circle. At the lowest point it moves at 5.5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 14 m along the slope.
A 0.5 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.2) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 12 g bullet is fired horizontally into a 2 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 17 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
An 8 g bullet is fired horizontally into a 3 kg block hanging from light strings 1.4 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A shaft transmits 96.5 kW at 2100 rpm. Find the torque T in the shaft.
A hollow sphere rolls without slipping down a slope inclined at 20° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 4 m down the slope?
A 0.75 kW motor running at 1500 rpm drives a pinion with 25 teeth, which meshes with a gear with 30 teeth. Ignore losses. Find the output torque T2 on the gear shaft.
In a compound gear train, gear A (32 teeth) on the input shaft turning at 960 rpm drives gear B (40 teeth). Gear C (32 teeth) is fixed to the same shaft as B and drives gear D (36 teeth) on the output shaft. Find the output speed nout.
A simple pendulum has a length of 1.9 m. Use g = 9.81 m/s². Find its period T for small swings.
A body oscillates in simple harmonic motion with period 2 s and amplitude 13 cm. What is the shortest time t it needs to move from equilibrium to a displacement of 10.4 cm?
A 40 kg mass on a spring with a stiffness of 8 kN/m has a viscous damper giving a damping ratio of 0.6. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from spring k₃ = 80 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 40 kN/m and k₂ = 60 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: a = 2.75 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: y = 3.964 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: F = 198.1 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Constant speed: the forces balance.
Answer: T = 93.82 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
Answer: x = 37.79 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: H = 50.62 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: vmax = 24.86 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 25.13 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: v = 12.85 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: x = 7.177 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v = 306.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 721.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: T = 438.8 N·m
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: t = 1.993 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: T2 = 5.73 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 682.7 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 1.406 : 1
Answer: T = 2.765 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: t = 0.2952 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 1.801 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 6.711 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics