Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 260 km/h to take off and the usable runway is 1000 m long. Starting from rest, what constant acceleration a does it need?
Ball A is dropped from rest from a height of 30 m. At the same instant ball B is thrown straight up from the ground directly below at 16 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
A 13 kg block slides down a frictionless slope at 25° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 3 kg block on a ramp at 40° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 10 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 50° above the horizontal and lands 10 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
A ball is launched at 15 m/s and 50° above the horizontal from the top of a 20 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
A car takes a flat curve of radius 40 m. The coefficient of static friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.3 kg ball on a string 0.9 m long is swung in a vertical circle. At the lowest point it moves at 9 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 20 m along the slope.
An 8 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 50 N parallel to the slope. The coefficient of kinetic friction is 0.15. Find the speed v of the block after it has moved 7 m up the slope.
A 1200 kg car moving at 23 m/s runs into a stationary 1900 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
A 0.35 kg ball hits a wall at 29 m/s and bounces straight back at 11 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
A flywheel with a moment of inertia of 13.5 kg·m² spins at 2800 rpm. A brake applies a constant friction torque of 15 N·m. How many revolutions N does the flywheel make before it stops?
A uniform slender rod of mass 5 kg and length 1.1 m hangs at rest from a frictionless pivot at its top end. A 35 g bullet moving horizontally at 200 m/s hits the rod 0.64 m below the pivot and stays embedded. Find the angular velocity ω of the rod just after the impact.
A 5.5 kW motor running at 2900 rpm drives a pinion with 30 teeth, which meshes with a gear with 50 teeth. The gear pair has an efficiency of 97%. Find the output torque T2 on the gear shaft.
In a compound gear train, gear A (16 teeth) on the input shaft turning at 2900 rpm drives gear B (48 teeth). Gear C (50 teeth) is fixed to the same shaft as B and drives gear D (60 teeth) on the output shaft. Find the output speed nout.
How long must a simple pendulum be to have a period of 2.7 s? Use g = 9.81 m/s². Find L.
A 3.6 kg mass on a spring with k = 470 N/m is pulled 7 cm from equilibrium and released. Find its maximum speed vmax.
A 100 kg mass is supported by a spring with a stiffness of 25 kN/m and a viscous damper with a damping coefficient of 320 N·s/m. Find the damping ratio ζ.
A 50 kg mass hangs from spring k₃ = 10 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 25 kN/m and k₂ = 5 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: a = 2.608 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 1.875 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: a = 4.146 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 41.53 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: v0 = 9.981 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: α = 67.17 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Energy or v² = v₀² + 2as in the vertical direction.
Answer: vmax = 14.01 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 129.8 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: v = 6.431 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 4.601 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: ΔK = 194535 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The lost energy goes into deformation, heat and sound.
Answer: Favg = 350 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: N = 6158 rev
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: ω = 2.206 rad/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
The pivot force passes through the pivot, so it has no moment there during the impact.
Answer: T2 = 29.28 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 805.6 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 3.6 : 1
Answer: L = 1.811 m
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.7998 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.1012
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 1.949 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics