Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane starts from rest and accelerates uniformly at 1.75 m/s² along a runway. Find its speed v after 1400 m.
A tram starts from rest and accelerates at 3 m/s² for 4 s, then runs at constant speed for 5 s, and finally brakes at 2 m/s² until it stops. Find the total distance s between the two stops.
A 14 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 10 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A ball is launched at 30 m/s and 20° above the horizontal from the top of a 35 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
A car takes a flat curve of radius 25 m. The coefficient of static friction between tyres and road is 0.5. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 0.5 kg ball on a string 0.7 m long is swung in a vertical circle. At the lowest point it moves at 8 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 7 m along the slope.
A 10 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.25) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
An 8 g bullet is fired horizontally into a 4 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 21 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 0.6 kg ball hits a wall at 11 m/s and bounces straight back at 10 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
A shaft transmits 41.5 kW at 1300 rpm. Find the torque T in the shaft.
A uniform solid disc (mass 21 kg, radius 0.3 m) spins freely at 150 rpm about a vertical frictionless shaft. A thin ring of mass 18 kg and the same radius is dropped onto it from rest, centred on the shaft, and the two quickly spin together. Find their common speed n2 in rpm.
An 80 mm pulley at 1450 rpm drives a 315 mm pulley by a belt with 1 % slip. Find the speed n2 of the driven pulley.
An open belt connects a 200 mm pulley and a 450 mm pulley whose centres are 600 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A 1.5 kg mass on a spring with k = 130 N/m oscillates on a frictionless surface with an amplitude of 18 cm. Find its speed v when it is 5 cm from equilibrium.
A mass on a spring with k = 390 N/m oscillates on a frictionless surface with an amplitude of 20 cm. Find the energy U stored in the spring when the mass is 7 cm from equilibrium.
A 20 kg mass is supported by a spring with a stiffness of 200 kN/m and a viscous damper with a damping coefficient of 1200 N·s/m. Find the damping ratio ζ.
A 25 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 15 kN/m and the lower one k₂ = 30 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: v = 70 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: s = 120 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 2.356 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: a = 1.899 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: x = 114.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: H = 40.37 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Answer: vmax = 11.07 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 50.62 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: v = 4.6 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 4.952 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v = 1017 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: Favg = 504 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: T = 304.8 N·m
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: n2 = 55.26 rpm
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: n2 = 364.6 rpm
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: θ = 156 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: v = 1.61 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: U = 0.9555 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.3
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 3.183 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/dynamics