Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 250 km/h to take off and the usable runway is 1800 m long. Starting from rest, what constant acceleration a does it need?
Ball A is dropped from rest from a height of 35 m. At the same instant ball B is thrown straight up from the ground directly below at 20 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
A 19 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 7 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 34 m/s and must land 50 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 21 m/s and 35° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
A car takes a flat curve of radius 35 m. The coefficient of static friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 0.2 kg ball on a light string 0.6 m long is swung in a vertical circle. At the lowest point its speed is 9 m/s. Ignore air resistance and use g = 9.81 m/s². Find the tension Ttop in the string at the highest point.
A toy launcher has a vertical spring of stiffness 1500 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 2 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
A 4 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.1) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
A 1000 kg car moving at 20 m/s runs into a stationary 800 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
A 0.4 kg ball hits a wall at 9 m/s and bounces straight back at 16 m/s. The contact lasts 5 ms. Find the magnitude of the impulse J the wall gives the ball.
A uniform slender rod of mass 2.5 kg and length 2.1 m is pinned at one end and released from rest in a horizontal position. Ignore friction and use g = 9.81 m/s². Find the speed v of the free end as the rod swings through the vertical position.
A solid sphere rolls without slipping down a slope inclined at 35° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of its centre.
A 0.55 kW motor at 1450 rpm drives a worm with 1 start(s). The worm wheel has 50 teeth and the drive has an efficiency of 50%. Find the output torque Tw on the wheel shaft.
In a compound gear train, gear A (15 teeth) on the input shaft turning at 1450 rpm drives gear B (16 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (60 teeth) on the output shaft. Find the output speed nout.
How long must a simple pendulum be to have a period of 0.8 s? Use g = 9.81 m/s². Find L.
A 3.6 kg mass on a spring with k = 390 N/m is pulled 18 cm from equilibrium and released. Find its maximum speed vmax.
In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 3 cycles later by a peak of 1 mm. Find the damping ratio ζ.
A 5 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 12 kN/m and k₂ = 100 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: a = 1.34 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 1.75 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: a = 4.823 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 29.76 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: θ = 12.55 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 77.45°.
Answer: v = 35.01 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Energy or v² = v₀² + 2as in the vertical direction.
Check with energy: v² = v₀² + 2gh.
Answer: vmax = 15.5 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: Ttop = 17.19 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Kinetic energy is traded for potential energy over a height 2r.
Tension and gravity both point down, towards the centre.
Answer: h = 0.2039 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 9.603 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: ΔK = 88889 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The lost energy goes into deformation, heat and sound.
Answer: J = 10 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 7.861 m/s
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: a = 4.019 m/s²
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: Tw = 90.55 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 271.9 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 5.333 : 1
Answer: L = 0.159 m
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 1.873 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.1213
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 112 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics