Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 180 km/h to take off and the usable runway is 1900 m long. Starting from rest, what constant acceleration a does it need?
A ball is thrown straight up at 15 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
An 8 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 4 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A ball is launched at 20° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
In a fairground rotor, riders stand against the wall of a vertical cylinder of radius 3.2 m. When it spins fast enough the floor drops away and friction holds them up. The coefficient of static friction is 0.8. Use g = 9.81 m/s². Find the smallest rotation rate n in revolutions per minute.
A 1.4 kg ball on a string 1.1 m long is swung in a vertical circle. At the lowest point it moves at 8 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A 5 kg block slides 5 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
A 2 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.3) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
A 1.5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
A 0.3 kg ball hits a wall at 30 m/s and bounces straight back at 6 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
A uniform slender rod of mass 9.5 kg and length 2.9 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find the vertical force R that the pin exerts on the rod just after release.
A thin hoop rolls without slipping down a slope inclined at 40° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 4.5 m down the slope?
Two parallel shafts are 108 mm apart. They must be connected by a pair of spur gears with a module of 2 mm and a speed reduction of 5 : 1. How many teeth N2 must the gear have?
In a compound gear train, gear A (12 teeth) on the input shaft turns at 1440 rpm and drives gear B (18 teeth). Gear C (72 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 864 rpm. How many teeth ND must gear D have?
A 1.2 kg mass on a spring with k = 390 N/m oscillates on a frictionless surface with an amplitude of 8 cm. Find its speed v when it is 7 cm from equilibrium.
A 4 kg mass on a spring with k = 430 N/m is pulled 2 cm from equilibrium and released. Find its maximum speed vmax.
An 80 kg mass on a spring with a stiffness of 40 kN/m has a viscous damper giving a damping ratio of 0.3. Find the damped natural frequency fd of its free vibration in Hz.
A 50 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 12 kN/m and k₂ = 12 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: a = 0.6579 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 4.437 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive and the ground is h₀ below the starting point.
Only the positive root is physical.
Answer: a = 5.179 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 22.72 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: t = 1.67 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: t = 3.727 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: n = 18.69 rpm
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 95.19 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: Wf = 34.68 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 3.706 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′2 = 4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: J = 10.8 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: R = 23.3 N
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
R = m·g/4, independent of the length.
Answer: t = 1.69 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N2 = 90
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: ND = 80
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: v = 0.6982 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.2074 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 3.395 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 3.487 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics