Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A driver moving at 36 km/h sees an obstacle. Her reaction time is 1.1 s, after which the car brakes with a constant deceleration of 7.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
A tram starts from rest and accelerates at 2.5 m/s² for 6 s, then runs at constant speed for 26 s, and finally brakes at 4 m/s² until it stops. Find the total distance s between the two stops.
A 15 kg box is pushed up a ramp at 25° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the pushing force F.
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
A ball is launched at 15° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A small ball on a string of length 1.9 m moves in a horizontal circle so that the string makes a constant angle of 35° with the vertical (a conical pendulum). Use g = 9.81 m/s². Find the time T for one revolution.
A small cart is released from rest on a frictionless track and runs into a vertical loop of radius 2 m. From what minimum height hmin above the bottom of the loop must it start to stay on the track at the top of the loop?
A 1 kg block slides 4 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.4. Find the work Wf done against friction.
A spring of stiffness 500 N/m at the bottom of a 15° slope is compressed by 20 cm against a 3 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 10 g bullet is fired horizontally into a 3.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 7 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 1400 kg car runs into a parked 1500 kg car. The wrecks lock together and skid 23.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A uniform slender rod of mass 2 kg and length 1.4 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find the acceleration atip of the free end just after release.
A uniform slender rod of mass 5 kg and length 1.9 m hangs at rest from a frictionless pivot at its top end. A 25 g bullet moving horizontally at 140 m/s hits the rod 1.36 m below the pivot and stays embedded. Find the angular velocity ω of the rod just after the impact.
Two parallel shafts are 120 mm apart. They must be connected by a pair of spur gears with a module of 2.5 mm and a speed reduction of 5 : 1. How many teeth N1 must the pinion have?
An open belt connects a 200 mm pulley and a 450 mm pulley whose centres are 600 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A simple pendulum has a length of 2.2 m. Use g = 9.81 m/s². Find its period T for small swings.
A 1.9 kg mass on a spring with k = 270 N/m is pulled 8 cm from equilibrium and released. Find the total energy E of the oscillation.
A 100 kg mass on a spring with a stiffness of 10 kN/m has a viscous damper giving a damping ratio of 0.5. Find the damped natural frequency fd of its free vibration in Hz.
A 40 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 40 kN/m and k₂ = 15 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: d = 17.67 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: s = 463.1 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: F = 88.86 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Constant speed: the forces balance.
Answer: T = 13.58 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: H = 34.58 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
At the top the vertical velocity is zero: vy² = 2gH.
Answer: x = 62.65 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: T = 2.503 s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Tension and gravity together give the inward force: tan θ = v²/(r·g).
Answer: hmin = 5 m
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: Wf = 12.86 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: d = 0.6194 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 411.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v1 = 39.78 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: atip = 14.71 m/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
atip = 1.5·g for any length: the free end falls faster than a dropped stone.
Answer: ω = 0.7851 rad/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
The pivot force passes through the pivot, so it has no moment there during the impact.
Answer: N1 = 16
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: θ = 156 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: T = 2.975 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 0.864 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 1.378 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 5.902 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics