Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane starts from rest and accelerates uniformly at 3 m/s² along a runway. Find its speed v after 1100 m.
A ball is thrown straight up at 12 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
Masses of 8 kg and 3 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 6 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
A ball is kicked from level ground at 26 m/s and 35° above the horizontal towards a wall 26 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
A ball is launched at 15° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
In a fairground rotor, riders stand against the wall of a vertical cylinder of radius 3.1 m. When it spins fast enough the floor drops away and friction holds them up. The coefficient of static friction is 0.7. Use g = 9.81 m/s². Find the smallest rotation rate n in revolutions per minute.
A ball on a string 0.9 m long is swung in a vertical circle. Use g = 9.81 m/s². What is the smallest speed vmin at the top for which the string just stays tight?
A 5 kg ball hangs on a light string of length 1.5 m. It is pulled aside until the string makes 30° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
A spring of stiffness 500 N/m at the bottom of a 20° slope is compressed by 10 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 3.5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
A 0.55 kg ball hits a wall at 18 m/s and bounces straight back at 14 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
A uniform slender rod of mass 17 kg and length 1 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find the vertical force R that the pin exerts on the rod just after release.
A uniform slender rod of mass 7 kg and length 1 m hangs at rest from a frictionless pivot at its top end. A 35 g bullet moving horizontally at 400 m/s hits the rod 1 m below the pivot and stays embedded. Use g = 9.81 m/s². Find the largest angle φ from the vertical through which the rod swings.
A 1.5 kW motor running at 1500 rpm drives a pinion with 36 teeth, which meshes with a gear with 72 teeth. The gear pair has an efficiency of 98%. Find the torque T1 on the motor shaft.
An open belt connects a 125 mm pulley and a 250 mm pulley whose centres are 500 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A simple pendulum has a length of 2.4 m. Use g = 9.81 m/s². Find its period T for small swings.
A 0.7 kg mass on a spring with k = 380 N/m is pulled 3 cm from equilibrium and released. Find its maximum speed vmax.
A 2 kg mass on a spring with a stiffness of 8 kN/m has a viscous damper giving a damping ratio of 0.45. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from spring k₃ = 20 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 40 kN/m and k₂ = 80 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: v = 81.24 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 22.34 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 4.459 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: a = 5.118 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: y = 10.9 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The ball is still rising at the wall.
Answer: t = 2.308 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: n = 20.3 rpm
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: vmin = 2.971 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 62.19 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Check: T = mg(3 − 2cos θ) = 62.19 N.
Answer: d = 0.4809 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v′1 = 0.4615 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: Favg = 3520 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: R = 41.69 N
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
R = m·g/4, independent of the length.
Answer: φ = 101.1 °
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
The pivot force passes through the pivot, so it has no moment there during the impact.
Answer: T1 = 9.549 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: θ = 165.6 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: T = 3.108 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.699 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 8.989 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 4.168 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics