Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 50 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
A tram starts from rest and accelerates at 2.5 m/s² for 5 s, then runs at constant speed for 17 s, and finally brakes at 4.5 m/s² until it stops. Find the total travel time t.
A 5 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 6 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 18 m/s and must land 15 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 30 m/s and 55° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
A car takes a flat curve of radius 150 m. The coefficient of static friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A ball on a string 1 m long is swung in a vertical circle. Use g = 9.81 m/s². What is the smallest speed vmin at the top for which the string just stays tight?
A block slides from rest down a slope at 15° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 17 m along the slope.
A 4 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
A 5 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
A 0.4 kg ball hits a wall at 9 m/s and bounces straight back at 5 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
A motor brings a flywheel with a moment of inertia of 10.5 kg·m² from rest up to 1100 rpm in 45 s. Ignoring losses, find the average power Pavg it delivers, in kW.
A solid cylinder rolls without slipping down a slope inclined at 25° to the horizontal. Use g = 9.81 m/s². Find the smallest coefficient of static friction μs that prevents it from slipping.
Two parallel shafts are 112 mm apart. They must be connected by a pair of spur gears with a module of 4 mm and a speed reduction of 2.5 : 1. How many teeth N1 must the pinion have?
In a compound gear train, gear A (15 teeth) on the input shaft turning at 1450 rpm drives gear B (18 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (18 teeth) on the output shaft. Find the output speed nout.
A 2.3 kg mass on a spring with k = 90 N/m is pulled 10 cm in the positive direction and released from rest at t = 0. Find its displacement x from equilibrium at t = 1.15 s (with sign).
A 2.8 kg mass is attached to the lower end of an unstretched vertical spring with k = 370 N/m and released from rest. Use g = 9.81 m/s². Find the greatest speed vmax of the mass.
A 5 kg mass is supported by a spring with a stiffness of 15 kN/m and a viscous damper with a damping coefficient of 220 N·s/m. Find the damping ratio ζ.
A 5 kg mass hangs from spring k₃ = 100 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 5 kN/m and k₂ = 15 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 4.63 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 24.78 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 4.02 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 38.85 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: θ = 13.51 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 76.49°.
Answer: α = 67.24 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Energy or v² = v₀² + 2as in the vertical direction.
Answer: vmax = 32.09 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: vmin = 3.132 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: v = 6.164 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: x = 33.44 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′2 = 7.059 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: J = 5.6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: Pavg = 1.548 kW
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: μs = 0.1554
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N1 = 16
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nout = 805.6 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 1.8 : 1
Answer: x = 6.133 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: vmax = 0.8534 m/s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
The speed is largest at equilibrium.
Answer: ζ = 0.4017
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 9.189 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics