Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A driver moving at 90 km/h sees an obstacle. Her reaction time is 1.3 s, after which the car brakes with a constant deceleration of 6 m/s². Find the total stopping distance d from the moment she sees the obstacle.
A tram starts from rest and accelerates at 1 m/s² for 7 s, then runs at constant speed for 24 s, and finally brakes at 4 m/s² until it stops. Find the total distance s between the two stops.
Masses of 7.5 kg and 4 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 36 m/s and must land 75 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 55° above horizontal from the top of a 25 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A car takes a flat curve of radius 20 m. The coefficient of static friction between tyres and road is 0.4. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A ball on a string 0.6 m long is swung in a vertical circle. Use g = 9.81 m/s². What is the smallest speed vmin at the top for which the string just stays tight?
A block slides from rest down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 9 m along the slope.
A 2 kg block is released from rest at height 1.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
A 3 kg glider moving at 7 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
A 0.3 kg ball hits a wall at 29 m/s and bounces straight back at 14 m/s. The contact lasts 50 ms. Find the magnitude of the impulse J the wall gives the ball.
A 1 kg block hangs from a light cord wrapped around a pulley, a uniform solid disc of mass 19 kg and radius 0.45 m that turns on a frictionless horizontal axle. The block is released from rest. Use g = 9.81 m/s². Find the angular acceleration α of the pulley.
A hollow sphere of mass 8.5 kg rolls without slipping at 3 m/s. Find its total kinetic energy Ek.
A 1.5 kW motor running at 960 rpm drives a pinion with 24 teeth, which meshes with a gear with 48 teeth. The gear pair has an efficiency of 98%. Find the torque T1 on the motor shaft.
In a compound gear train, gear A (18 teeth) on the input shaft turning at 1500 rpm drives gear B (25 teeth). Gear C (32 teeth) is fixed to the same shaft as B and drives gear D (50 teeth) on the output shaft. Find the output speed nout.
How long must a simple pendulum be to have a period of 0.9 s? Use g = 9.81 m/s². Find L.
A 2.5 kg mass on a spring with k = 80 N/m is pulled 12 cm from equilibrium and released. Find its maximum acceleration amax.
A 25 kg mass on a spring with a stiffness of 4 kN/m has a viscous damper giving a damping ratio of 0.4. Find the damped natural frequency fd of its free vibration in Hz.
A 20 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 5 kN/m and k₂ = 60 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: d = 84.58 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: s = 198.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: T = 51.18 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: T = 39.42 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: θ = 17.3 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 72.7°.
Answer: x = 95.35 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 8.859 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: vmin = 2.426 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: v = 7.707 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 5.147 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The ramp is smooth, so only the strip removes energy.
Answer: v′1 = 3.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Solving momentum and energy conservation together gives these two results.
Answer: J = 12.9 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: α = 2.076 rad/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: Ek = 63.75 J
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: T1 = 14.92 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 691.2 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2.17 : 1
Answer: L = 0.2013 m
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: amax = 3.84 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 1.845 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 65 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics