Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 50 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
Ball A is dropped from rest from a height of 15 m. At the same instant ball B is thrown straight up from the ground directly below at 27 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
A box slides across a level floor with an initial speed of 5.5 m/s and comes to rest after 31 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
A 2 kg block on a ramp at 40° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 5.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
A ball is launched at 20° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A car takes a flat curve of radius 135 m. The coefficient of static friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 1.9 kg ball on a string 0.6 m long is swung in a vertical circle. At the lowest point it moves at 5 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A block slides from rest down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 18 m along the slope.
A 3 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 1 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
A 12 g bullet is fired horizontally into a 5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 20 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 0.3 kg ball hits a wall at 14 m/s and bounces straight back at 6 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
A motor delivers a torque of 560 N·m at 800 rpm. Find its power output P in kW.
A hollow sphere rolls without slipping down a slope inclined at 20° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 1.5 m down the slope?
A 5.5 kW motor running at 2900 rpm drives a pinion with 24 teeth, which meshes with a gear with 25 teeth. The gear pair has an efficiency of 96%. Find the output torque T2 on the gear shaft.
In a compound gear train, gear A (30 teeth) on the input shaft turning at 3000 rpm drives gear B (36 teeth). Gear C (30 teeth) is fixed to the same shaft as B and drives gear D (50 teeth) on the output shaft. Find the output speed nout.
An astronaut on another planet finds that a simple pendulum 2 m long has a period of 2.66 s for small swings. Find the gravitational acceleration g on that planet.
A 2.4 kg mass on a spring with k = 460 N/m is pulled 5 cm from equilibrium and released. Find the total energy E of the oscillation.
A 25 kg mass is supported by a spring with a stiffness of 40 kN/m and a viscous damper with a damping coefficient of 600 N·s/m. Find the damping ratio ζ.
A 5 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 50 kN/m and k₂ = 100 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: t = 4.63 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 0.5556 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Up is positive, the ground is y = 0.
Answer: μ = 0.04974
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: T = 24.74 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: H = 15.29 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
At the top the vertical velocity is zero: vy² = 2gH.
Answer: t = 2.148 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 30.45 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 97.81 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: v = 11.43 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
Answer: v = 1.642 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 827.4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: J = 6 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: P = 46.91 kW
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: t = 1.221 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: T2 = 18.11 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 1500 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2 : 1
Answer: g = 11.16 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 0.575 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.3
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 27.57 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/dynamics