Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 120 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
A tram starts from rest and accelerates at 1 m/s² for 10 s, then runs at constant speed for 30 s, and finally brakes at 2 m/s² until it stops. Find the total distance s between the two stops.
Masses of 6.5 kg and 4 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 10.5 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
A ball is launched from level ground at 26 m/s and must land 60 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 15° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A car takes a flat curve of radius 20 m. The coefficient of static friction between tyres and road is 0.4. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A curve of radius 110 m is banked at 18°, and the coefficient of static friction between tyres and road is 0.1. Use g = 9.81 m/s². Find the highest speed vmax at which a car can take the curve without sliding up and out.
A 0.2 kg ball hangs on a light string of length 0.5 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
A 5 kg cart is released from rest at a height of 7.5 m on a smooth track that leads into a vertical circular loop of radius 2.5 m. Find the normal force N the track exerts on the cart at the top of the loop.
A 5 g bullet is fired horizontally into a 5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 25 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 1000 kg car runs into a parked 1700 kg car. The wrecks lock together and skid 23.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.6. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A uniform slender rod of mass 13 kg and length 0.7 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find its angular acceleration α just after release.
A uniform solid disc (mass 34 kg, radius 0.2 m) spins freely at 1200 rpm about a vertical frictionless shaft. A thin ring of mass 7 kg and the same radius is dropped onto it from rest, centred on the shaft, and the two quickly spin together. Find their common speed n2 in rpm.
Two parallel shafts are 105 mm apart. They must be connected by a pair of spur gears with a module of 2 mm and a speed reduction of 2.5 : 1. How many teeth N2 must the gear have?
In a compound gear train, gear A (16 teeth) on the input shaft turning at 2900 rpm drives gear B (24 teeth). Gear C (24 teeth) is fixed to the same shaft as B and drives gear D (36 teeth) on the output shaft. Find the output speed nout.
An astronaut on another planet finds that a simple pendulum 1.8 m long has a period of 4.37 s for small swings. Find the gravitational acceleration g on that planet.
A 0.6 kg mass is attached to the lower end of an unstretched vertical spring with k = 340 N/m and released from rest. Use g = 9.81 m/s². Find the greatest extension xmax of the spring in cm.
A 50 kg mass on a spring with a stiffness of 20 kN/m has a viscous damper giving a damping ratio of 0.35. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 40 kN/m and the lower one k₂ = 100 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: s = 85.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: s = 375 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: T = 48.58 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: d = 9.006 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Both forces point down the slope; the mass cancels.
Answer: θ = 30.27 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 59.73°.
Answer: x = 65.54 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 8.859 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: vmax = 21.77 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Friction points down the slope.
Answer: T = 3.364 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Check: T = mg(3 − 2cos θ) = 3.364 N.
Answer: N = 49.05 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
The cart just makes it round when h = 2.5R; then N = 0 at the top.
Answer: v = 2217 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v1 = 44.91 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: α = 21.02 rad/s²
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
Answer: n2 = 850 rpm
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N2 = 75
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nout = 1289 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2.25 : 1
Answer: g = 3.721 m/s²
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: xmax = 3.462 cm
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 2.982 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 28.57 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/dynamics