Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A car driving at 90 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. Find the braking distance s.
A ball is thrown straight up at 12 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
An 11 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
A 6.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
A ball is thrown from ground level at 17 m/s and 60° above the horizontal. It lands on the flat roof of a building 6 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
A road engineer wants cars to take a curve of radius 240 m at 120 km/h without relying on friction. Use g = 9.81 m/s². Find the banking angle θ.
A 0.4 kg ball on a string 0.9 m long is swung in a vertical circle. At the lowest point it moves at 9 m/s. Use g = 9.81 m/s². Find the tension T in the string at the lowest point.
A toy launcher has a vertical spring of stiffness 800 N/m. A 0.05 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
A 2 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 3 m.
A 1500 kg car moving at 16 m/s runs into a stationary 1900 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
A 0.25 kg ball hits a wall at 23 m/s and bounces straight back at 5 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
A 6 kg block hangs from a light cord wrapped around a pulley, a uniform solid disc of mass 10.5 kg and radius 0.15 m that turns on a frictionless horizontal axle. The block is released from rest. Use g = 9.81 m/s². Find the tension T in the cord.
A solid sphere starts from rest and rolls without slipping down a slope inclined at 10° to the horizontal. Use g = 9.81 m/s². Its radius is 0.2 m. Find its angular velocity ω after it has rolled 4.5 m along the slope.
A 200 mm pulley at 1440 rpm drives a 250 mm pulley by a belt with 2 % slip. Find the speed n2 of the driven pulley.
In a compound gear train, gear A (20 teeth) on the input shaft turns at 1440 rpm and drives gear B (60 teeth). Gear C (24 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 460.8 rpm. How many teeth ND must gear D have?
A simple pendulum has a length of 1.4 m. Use g = 9.81 m/s². Find its period T for small swings.
A 2.8 kg mass on a spring with k = 100 N/m is pulled 20 cm from equilibrium and released. Find the total energy E of the oscillation.
In a free-vibration test of a damped mass–spring system, a displacement peak of 25 mm is followed 3 cycles later by a peak of 9.7 mm. Find the damping ratio ζ.
A 5 kg mass hangs from spring k₃ = 60 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 60 kN/m and k₂ = 12 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: s = 89.29 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: hmax = 17.34 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: a = 1.512 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Down the slope is positive.
Answer: T = 29.01 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: x = 132.1 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Starting and landing at the same height: t = 2vy/g.
Answer: x = 21.38 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Larger root: the ball is descending.
Answer: θ = 25.26 °
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: T = 39.92 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre (up) is positive.
Answer: h = 8.155 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: v = 5.638 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Answer: ΔK/K = 55.88 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
The lost energy goes into deformation, heat and sound.
Answer: Favg = 175 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: T = 27.47 N
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
Answer: ω = 16.55 rad/s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Rolling without slipping: ω = v/r, and friction does no work at the contact point.
Answer: n2 = 1129 rpm
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: ND = 25
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: T = 2.374 s
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: E = 2 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: ζ = 0.05016
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 12.88 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics