Formula sheets, the key method steps for every topic and 20 practice problems, with full solutions at the back.
A plane needs a speed of 200 km/h to take off and the usable runway is 1300 m long. Starting from rest, what constant acceleration a does it need?
A tram starts from rest and accelerates at 2.5 m/s² for 4 s, then runs at constant speed for 18 s, and finally brakes at 2.5 m/s² until it stops. Find the total travel time t.
Masses of 7 kg and 3.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
A ball is launched from level ground at 38 m/s and must land 110 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
A ball is launched at 55° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
A car takes a flat curve of radius 45 m. The coefficient of static friction between tyres and road is 0.6. Use g = 9.81 m/s². Find the highest speed vmax at which the car can take the curve without skidding.
A 2 kg cart is released from rest at a height of 20.8 m on a frictionless track and runs through a vertical loop of radius 6.5 m. Use g = 9.81 m/s². Find the normal force Ntop of the track on the cart at the top of the loop.
A car travelling at 40 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
A 5 kg cart is released from rest at a height of 10.5 m on a smooth track that leads into a vertical circular loop of radius 3 m. Find the normal force N the track exerts on the cart at the top of the loop.
A 20 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 18 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A 15 g bullet is fired horizontally into a 3.5 kg block hanging from light strings 0.6 m long, and stays in it. The strings swing out to a largest angle of 10° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
A uniform slender rod of mass 16 kg and length 1.6 m is pinned at one end and held horizontal. It is released from rest. Use g = 9.81 m/s². Find the vertical force R that the pin exerts on the rod just after release.
A solid cylinder rolls without slipping down a slope inclined at 30° to the horizontal. Use g = 9.81 m/s². It starts from rest. How long t does it take to roll 5 m down the slope?
Two parallel shafts are 135 mm apart. They must be connected by a pair of spur gears with a module of 3 mm and a speed reduction of 4 : 1. How many teeth N1 must the pinion have?
A 5.5 kW motor at 2900 rpm drives gear A (16 teeth), which meshes with gear B (45 teeth). Gear C (18 teeth) on the same shaft as B drives gear D (80 teeth) on the output shaft. Each gear mesh has an efficiency of 97%. Find the output torque Tout.
How long must a simple pendulum be to have a period of 1.7 s? Use g = 9.81 m/s². Find L.
A mass on a spring with k = 500 N/m oscillates on a frictionless surface with an amplitude of 6 cm. Find the energy U stored in the spring when the mass is 5 cm from equilibrium.
A 5 kg mass on a spring with a stiffness of 25 kN/m has a viscous damper giving a damping ratio of 0.4. Find the damped natural frequency fd of its free vibration in Hz.
A 50 kg mass hangs from spring k₃ = 20 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 100 kN/m and k₂ = 15 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: a = 1.187 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: t = 26 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Answer: T = 45.78 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
The net driving force is the difference of the weights; it moves the total mass.
Answer: T = 12.61 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Answer: θ = 24.18 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
The other solution is 90° − θ = 65.82°.
Answer: t = 5.129 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
Answer: vmax = 16.27 m/s
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Answer: Ntop = 27.47 N
Uniform circular motion: an object moving at speed v on a circle of radius r accelerates towards the centre with a = v²/r, so it needs a net inward force F = m·v²/r. That force is supplied by something real: friction, tension, gravity or a normal force.
Towards the centre is positive.
Answer: d = 8.989 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Doubling the speed makes the stopping distance four times longer.
Answer: N = 98.1 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
The cart just makes it round when h = 2.5R; then N = 0 at the top.
Answer: v = 142.8 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: v = 99.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Answer: R = 39.24 N
Rotation about a fixed axis: the sum of the moments about the axis equals I·α (ΣM = I·α), just as ΣF = m·a for translation. In energy form, a torque T turning through an angle θ (in radians) does work T·θ, which changes the kinetic energy ½·I·ω²; gravity adds or removes m·g·Δh of the centre of mass. Power is P = T·ω.
At the moment of release ω = 0, so there is no centripetal acceleration and the centre accelerates straight down.
R = m·g/4, independent of the length.
Answer: t = 1.749 s
Rolling and angular momentum: a body rolling without slipping has v = ω·r, so its kinetic energy is ½·m·v² + ½·I·ω² = ½·m·v²·(1 + I/(m·r²)). Down a slope that gives a = g·sin θ/(1 + I/(m·r²)). When no external moment acts about an axis, the angular momentum about that axis stays constant, I₁·ω₁ = I₂·ω₂, even if kinetic energy is lost.
Answer: N1 = 18
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: Tout = 213 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: L = 0.7181 m
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: U = 0.625 J
Simple harmonic motion: a mass m on a spring of stiffness k oscillates with angular frequency ω = √(k/m) and period T = 2π/ω = 2π·√(m/k). A simple pendulum of length L has T = 2π·√(L/g). With amplitude A, the largest speed is A·ω, the largest acceleration A·ω² and the energy ½·k·A².
Answer: fd = 10.31 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 2.938 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/dynamics