Formula sheets, the key method steps for every topic and 16 practice problems, with full solutions at the back.
Find the current IR1 delivered by the source, which flows through R1.
Find the equivalent resistance Req seen by the source V1.
Use nodal analysis to find the node voltage VB (measured from ground).
Use nodal analysis to find the current IR4 through R4 in the direction of the arrow.
Find the Thévenin voltage Vth seen from terminals a–b.
A load RL = 25 Ω is connected across a–b. Use a Thévenin equivalent to find the power PL delivered to the load.
The inductor carries no current before the switch closes at t = 0. Find the voltage vL across the inductor at t = 5 ms.
Just before the switch closes at t = 0, the capacitor holds 6 V with the polarity shown. How long does it take for vC to reach 11.4 V? Find t.
A series RLC circuit with C = 47 µF must resonate at 50 Hz. Find the inductance L needed.
A series RLC circuit has R = 20 Ω, L = 20 mH and C = 2.2 µF. Find its quality factor Q at resonance.
A single-phase motor takes 15 kW at a power factor of 0.75 lagging from a 230 V supply. Find the line current I.
A single-phase load takes 40 kW at a power factor of 0.65 lagging from a 240 V, 60 Hz supply. A capacitor connected in parallel raises the power factor to 0.98. Find the capacitance C needed.
A balanced Y-connected load with an impedance of 7 + j24 Ω per phase is connected to a balanced three-phase supply with a line-to-line voltage of 480 V. Find the total real power P absorbed by the load in kW.
A balanced three-phase load takes 150 kW at a power factor of 0.78 lagging from a 690 V (line-to-line), 50 Hz supply. A three-phase capacitor bank in parallel with the load must raise the overall power factor to 0.98 lagging. The real power stays the same. The capacitors are connected in Y. Find the capacitance Cph of each capacitor in µF.
A single-phase 25 kVA, 4160/480 V transformer operates at its rated load. Treat it as ideal. Find the current IHV in the high-voltage winding.
A single-phase 200 kVA transformer has a core loss of 800 W and a copper loss of 2400 W at rated load. It supplies 25% of its rated kVA at a power factor of 0.95 lagging. Find the total losses Ploss in watts at this load.
Answer: IR1 = 1.65 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
Answer: Req = 9.174 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
Answer: VB = 19.44 V
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
Ground is the bottom wire. Known node voltages come straight from the sources (V1 = 10 V). Unknowns: VA, VB.
Currents leaving A through the resistors equal the current pushed into A by sources.
Currents leaving B through the resistors equal the current pushed into B by sources.
Answer: IR4 = −0.251 A
Nodal analysis: choose a reference node, label the unknown node voltages, write Kirchhoff’s current law at each unknown node using Ohm’s law (I = ΔV/R), and solve the resulting equations.
Ground is the bottom wire. Known node voltages come straight from the sources (V1 = 36 V, V2 = 24 V). Unknowns: VA, VB.
Currents leaving A through the resistors equal the current pushed into A by sources.
Currents leaving B through the resistors equal the current pushed into B by sources.
Answer: Vth = 4.286 V
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
With a–b open, no current flows through R₃, so there is no drop across it and V_b = V_A. R₁ and R₂ form a voltage divider.
Answer: PL = 12.59 W
Thévenin’s theorem: any linear two-terminal network behaves like a single voltage source Vth in series with a resistance Rth. Norton’s theorem gives the same network as a current source IN = Vth/Rth in parallel with Rth.
Replace voltage sources with shorts and current sources with opens, then look into the circuit from a–b.
With a–b open, the only path for Iₛ is through R₃ into node A. Find V_A by superposition of V₁ and Iₛ, then add the drop across R₃.
The Thévenin source and R_th in series behave exactly like the original circuit at a–b, so the load sees a simple series loop.
Answer: vL = 3.329 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.
Answer: t = 114 ms
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.
Answer: L = 215.6 mH
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC).
Answer: Q = 4.767
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Q compares the reactance at resonance with the resistance: Q = ω₀L/R.
Answer: I = 86.96 A
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
Only the real part of the power does work, so divide by the power factor.
Answer: C = 1780 µF
AC power: apparent power S = V·I (VA) splits into real power P = S·cos φ (W), which does useful work, and reactive power Q = S·sin φ (var), which moves back and forth between source and load. The power factor is cos φ. A capacitor in parallel supplies reactive power locally, so the line current drops for the same real power.
The real power P does not change; only the reactive power drawn from the supply does.
A capacitor across the supply delivers Q = V²·ωC.
Answer: P = 2.58 kW
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ.
Only the resistive part of each impedance absorbs real power.
Check: cos φ = R/|Z| = 0.28, and √3·VL·IL·cos φ gives the same power.
Answer: Cph = 600.9 µF
Balanced three-phase systems: in a Y (star) connection the line-to-line voltage is √3 times the phase voltage, VL = √3·Vph, and the line current equals the phase current. In a Δ (delta) connection the line-to-line voltage equals the phase voltage and the line current is √3 times the phase current, IL = √3·Iph. The total power is three times the power of one phase: P = 3·Vph·Iph·cos φ = √3·VL·IL·cos φ. Power factor correction: capacitors supply reactive power locally, QC = P·(tan φ1 − tan φ2). Each of the three capacitors supplies QC/3 = V²·ω·C, where V is the voltage across that capacitor: VL in a Δ bank, VL/√3 in a Y bank.
The real power is unchanged, so each power factor fixes the reactive power: Q = P·tan φ.
In a Y bank each capacitor is connected between a line and the star point.
Answer: IHV = 6.01 A
Ideal transformer: the voltages are in the ratio of the turns and the currents in the inverse ratio: V₁/V₂ = N₁/N₂ = a and I₁/I₂ = N₂/N₁ = 1/a, so the power in equals the power out, V₁·I₁ = V₂·I₂. A load impedance Z on the secondary looks like a²·Z from the primary.
Both windings carry the same apparent power.
Answer: Ploss = 950 W
Transformer losses: the core loss (hysteresis and eddy currents) depends on the voltage and is the same at any load. The copper loss in the windings goes with the current squared, so at a fraction x of rated load it is x²·Pcu,fl. Efficiency η = Pout/(Pout + Pcore + Pcu), with Pout = x·S·pf. The efficiency is highest at the load where the copper loss equals the core loss.
The core loss is the same at any load.
The efficiency at this load is η = 98.04%.
ExamProblems · examproblems.com/courses/electrical-engineering-fundamentals