Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−24 VR = ?2 × 3 V5 mA

2 white LEDs (forward voltage 3 V each) are connected in series with a resistor to a 24 V supply. Find the resistance R that sets the current to 5 mA.

Vs = 24 VVF = 3 Vn = 2I = 5 mA
R = Ω
2.Diodes & transistorsHard
+−≤ 22 V470 Ω12 V

A 12 V Zener regulator has a 470 Ω series resistor. The input can rise to 22 V, and the load may be disconnected. Find the largest power PZ,max the Zener must dissipate.

Vin,max = 22 VVZ = 12 VR = 470 Ω
PZ,max = mW
3.Op-amp circuitsMedium
−+Vout​Rf​ = 10 kΩR1​ = 1 kΩVin​

The op-amp is ideal and runs from ±15 V supplies; its output saturates at ±14 V. The non-inverting amplifier is driven by a sine wave. Find the largest input amplitude Vin,max (peak value) for which the output does not clip.

R1 = 1 kΩRf = 10 kΩVsat = ±14 V
Vin,max = V
4.Op-amp circuitsHard
−+Vout​Rf​ = 47 kΩV1​ = −0.7 VR1​ = 4.7 kΩV2​ = −0.3 VR2​ = 47 kΩIf​

The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the current If through the feedback resistor, flowing towards the output.

V1 = −0.7 VV2 = −0.3 VR1 = 4.7 kΩR2 = 47 kΩRf = 47 kΩ
If = mA
5.RC & RL transientsMedium
+−Vs​12 Vt = 0R1​ = 4.7 kΩR2​ = 3.3 kΩC22 µF+−vC​

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the time constant τ of the circuit after the switch closes.

Vs = 12 VR1 = 4.7 kΩR2 = 3.3 kΩC = 22 µF
τ = ms
6.RC & RL transientsHard
+−Vs​5 Vt = 0R = 1 kΩC68 µF+−vC​vC​(0) = 6 V

Just before the switch closes at t = 0, the capacitor holds 6 V with the polarity shown. Find the capacitor voltage vC at t = 80 ms.

Vs = 5 VR = 1 kΩC = 68 µFvC(0) = 6 Vt = 80 ms
vC = V
7.Series & parallel resistorsMedium
R1​ = 8 ΩR3​ = 20 Ω+−V1​18 VR2​6 ΩIR2​AR4​12 ΩB

Find the current IR2 through R2.

V1 = 18 VR1 = 8 ΩR2 = 6 ΩR3 = 20 ΩR4 = 12 Ω
IR2 = A
8.Series & parallel resistorsHard
R1​ = 30 ΩR3​ = 30 ΩR5​ = 3 Ω+−V1​15 VR2​30 ΩAR4​5 ΩBR6​20 Ω

Find the equivalent resistance Req seen by the source V1.

V1 = 15 VR1 = 30 ΩR2 = 30 ΩR3 = 30 ΩR4 = 5 ΩR5 = 3 ΩR6 = 20 Ω
Req = Ω
9.DC-DC convertersMedium
tiL​Imax​Imin​ΔI = ?DTT2T

An ideal buck converter turns 36 V into 25.2 V at 20 kHz with L = 100 µH. Find the peak-to-peak inductor ripple current ΔIL.

Vin​ = 36 VVo​ = 25.2 Vf = 20 kHzL = 100 µH
ΔIL = A
10.DC-DC convertersHard
tiL​Imax​IL​DTT2T

An ideal inverting buck-boost converter turns 36 V into −108 V for a 2 Ω load at 200 kHz. Find the smallest inductance Lcrit for continuous conduction.

Vin​ = 36 VVo​ = −108 Vf = 200 kHzR = 2 Ω
Lcrit = µH
11.Wheatstone bridge & strain gaugesMedium
+−9 V500 Ω500 Ω + ΔR500 Ω500 Ωab+−44.55 mV

A bridge with four 500 Ω arms is supplied with 9 V. When the sensor R₂ changes, the output reads Vab = 44.55 mV. Find the exact change ΔR of R₂.

Vs = 9 VR = 500 ΩVab = 44.55 mV
ΔR = Ω
12.Wheatstone bridge & strain gaugesHard
+−5 V120 Ω − ΔR120 Ω + ΔR120 Ω + ΔR120 Ω − ΔRab+−Vo​ = ?

A load cell (a full bridge of strain gauges) has a rated output of 2.5 mV/V at its rated load of 50 kg. It is excited with 5 V. Find its output Vo under a load of 10 kg.

2.5 mV/VFrated = 50 kgVs = 5 VF = 10 kg
Vo = mV
13.Digital logic: gates, K-maps & flip-flopsMedium
ABCD000111100001111000111302140517061120131151140809111010

Use the Karnaugh map to find the minimal sum-of-products (SOP) form of F(A, B, C, D) = Σm(1, 3, 4, 7, 11, 12, 14, 15). How many product terms N does it have?

F(A, B, C, D) = Σm(1, 3, 4, 7, 11, 12, 14, 15)
N =
14.Digital logic: gates, K-maps & flip-flopsHard
DQ3​Q3​DQ2​Q2​DQ1​Q1​DQ0​Q0​CLKSHIFT

A 4-bit shift register Q₃Q₂Q₁Q₀ holds 1001. At every clock edge the bits shift one place to the right (Q₃ → Q₂ → Q₁ → Q₀, Q₀ is lost) and the serial input enters Q₃. The serial input is 1, 1, 1, 0, 1, 1 at the 6 edges. Give the final state Q = Q₃Q₂Q₁Q₀ as a decimal number.

Q₃Q₂Q₁Q₀ = 10011, 1, 1, 0, 1, 1
Q =

3Solutions

1.Diodes & transistors

Answer: R = 3600 Ω

LED and diode circuits: a forward-biased LED drops roughly its forward voltage VF (about 2 V for red, 3 V for blue or white), whatever the current. A series resistor sets the current: R = (Vs − n·VF)/I for n LEDs in series. With a more exact diode model V = V₀ + I·rd, the operating point is where the diode line meets the load line I = (Vs − V)/R, so I = (Vs − V₀)/(R + rd).

Voltage across the resistor

VR = 24 − 2·3 = 18 V

Resistance

R = 18/0.005 = 3600 Ω

Answer

R = 3600 Ω

The resistor dissipates 90 mW.

2.Diodes & transistors

Answer: PZ,max = 255.3 mW

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case Zener current

IZ = 10/470 = 21.28 mA

Zener power

PZ = 12·21.28 = 255.3 mW

Answer

PZ,max = 255.3 mW
3.Op-amp circuits

Answer: Vin,max = 1.273 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain

Av = 1 + Rf/R1 = 1 + 10/1 = 11

Largest input before clipping

Vin,max = Vsat/|Av| = 14/11 = 1.273 V

Answer

Vin,max = 1.273 V
4.Op-amp circuits

Answer: If = −0.1553 mA

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input currents

V₋ = 0, so each input resistor has its full input voltage across it.

I1 = V1/R1 = −0.7/4.7 = −0.1489 mA
I2 = V2/R2 = −0.3/47 = −0.006383 mA
If = I1 + I2 = −0.1553 mA

Answer

If = −0.1553 mA
5.RC & RL transients

Answer: τ = 42.65 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find Rth; open the capacitor to find the voltage it will settle at.

Rth = R1 ∥ R2 = 4.7·3.3/(4.7 + 3.3) = 1.939 kΩ
vC(∞) = 12·3.3/(4.7 + 3.3) = 4.95 V

Time constant

τ = Rth·C = 1.939·22 = 42.65 ms

Answer

τ = 42.65 ms
6.RC & RL transients

Answer: vC = 5.308 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 6 V, vC(∞) = Vs = 5 V
τ = R·C = 1 kΩ · 68 µF = 68 ms
vC(t) = 5 + (6 − 5)·e−t/τ

Voltage at the given time

vC(80) = 5 + (1)·e−80/68 = 5.308 V

Answer

vC = 5.308 V
7.Series & parallel resistors

Answer: IR2 = 1.161 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 8 ΩR3​ = 20 Ω+−V1​18 VR2​6 ΩAR4​12 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 20 + 12 = 32 Ω
R2 ∥ 32 = 6·32/(6+32) = 5.053 Ω
Req = R1 + 5.053 = 8 + 5.053 = 13.05 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 18/13.05 = 1.379 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

VA = V1 − IR1·R1 = 18 − 1.379·8 = 6.968 V
IR2 = VA/R2 = 6.968/6 = 1.161 A

Answer

IR2 = 1.161 A
8.Series & parallel resistors

Answer: Req = 45.96 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 30 ΩR3​ = 30 ΩR5​ = 3 Ω+−V1​15 VR2​30 ΩAR4​5 ΩBR6​20 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 3 + 20 = 23 Ω
R4 ∥ 23 = 4.107 Ω
R3 + 4.107 = 34.11 Ω
R2 ∥ 34.11 = 15.96 Ω
Req = R1 + 15.96 = 30 + 15.96 = 45.96 Ω

Answer

Req = 45.96 Ω
9.DC-DC converters

Answer: ΔIL = 3.78 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 25.2/36 = 0.7

Inductor voltage during the on-time

While S is on, the inductor sits between Vin and Vo.

VL = 36 − 25.2 = 10.8 V

Ripple current

ΔIL = VL·D/(L·f) = 10.8·0.7/(100·10⁻⁶·20·10³) = 3.78 A

Answer

ΔIL = 3.78 A
10.DC-DC converters

Answer: Lcrit = 0.3125 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 108/(36 + 108) = 0.75

Boundary condition

Set the average inductor current equal to half the ripple current and solve for L.

Lcrit = (1 − D)²·R/(2f)

Critical inductance

Lcrit = (1 − 0.75)²·2/(2200·10³) = 0.3125 µH

Answer

Lcrit = 0.3125 µH
11.Wheatstone bridge & strain gauges

Answer: ΔR = 9.999 Ω

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Node voltage

Va = 4.5 + 0.04455 = 4.545 V

Solve the divider

R₂ = 500·4.545/(9 − 4.545) = 510 Ω
ΔR = 510 − 500 = 9.999 Ω

Answer

ΔR = 9.999 Ω
12.Wheatstone bridge & strain gauges

Answer: Vo = 2.5 mV

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Full-scale output

2.5·5 = 12.5 mV

Output at this load

Vo = 12.5·10/50 = 2.5 mV

Answer

Vo = 2.5 mV
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 4

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

ABCD000111100001111000111302140517061120131151140809111010

Group the 1s

Every group is a rectangle of 2ᵏ cells; edge cells are neighbours of the cells on the opposite edge.

CD
BC′D′
A′B′D
ABD′

Minimal SOP form

F = CD + BC′D′ + A′B′D + ABD′
N = 4

Answer

N = 4

Another grouping of the same size exists; it has the same number of terms and literals.

14.Digital logic: gates, K-maps & flip-flops

Answer: Q = 13

Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.

State after every edge

1001 → 1100 → 1110 → 1111 → 0111 → 1011 → 1101

Decimal value

1101₂ = 13

Answer

Q = 13

ExamProblems · examproblems.com/courses/electronics-1