Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Digital logic: gates, K-maps & flip-flops
Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states
Method
For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.
2Practice problems
1.Diodes & transistorsMedium
An NPN transistor with β = 150 has voltage-divider bias from VCC = 12 V: R₁ = 39 kΩ from VCC to the base and R₂ = 6.8 kΩ from the base to ground. The collector resistor is RC = 1 kΩ and the emitter resistor is RE = 680 Ω. Take VBE = 0.7 V and use the Thévenin equivalent of the divider (do not neglect the base current). Find the collector–emitter voltage VCE.
An NPN transistor with β = 80 switches a 330 Ω load resistor connected between VCC = 12 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. For reliable switching, design for a base current 5 times the minimum needed for saturation. Find RB in kΩ.
The inductor carries a steady current of 0.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the current i at t = 1 ms.
i(0) = 0.5 AR = 47 ΩL = 10 mHt = 1 ms
i = A
6.RC & RL transientsHard
Just before the switch closes at t = 0, the capacitor holds 18 V with the polarity shown. How long does it take for vC to reach 15.6 V? Find t.
Vs = 10 VR = 2.2 kΩC = 220 µFvC(0) = 18 V
t = ms
7.Series & parallel resistorsMedium
Find the current IR2 through R2.
V1 = 15 VR1 = 15 ΩR2 = 5 ΩR3 = 6 ΩR4 = 20 Ω
IR2 = A
8.Series & parallel resistorsHard
Find the equivalent resistance Req seen by the source V1.
An ideal inverting buck-boost converter turns 48 V into −144 V for a 50 Ω load at 200 kHz. Find the smallest inductance Lcrit for continuous conduction.
Vin = 48 VVo = −144 Vf = 200 kHzR = 50 Ω
Lcrit = µH
11.Wheatstone bridge & strain gaugesMedium
A bridge has four 1000 Ω arms and Vs = 3 V. The sensor R₂ increases by ΔR = 250 Ω. Find the exact output Vab in mV.
Vs = 3 VR = 1000 ΩΔR = 250 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
A 350 Ω strain gauge with gauge factor 2 is bonded to a steel bar. Under load its resistance rises by 1.05 Ω. Find the strain ε in microstrain (µε).
In this Karnaugh map exactly one 1 has no neighbouring 1, so it stays a group of one cell (a full minterm of four literals) in the minimal SOP form. Neighbours across the map edges count. Click that cell.
F = Σm(0, 1, 2, 3, 5, 8, 10, 15)
1AB = 00, CD = 00
2AB = 00, CD = 01
3AB = 00, CD = 11
4AB = 00, CD = 10
5AB = 01, CD = 00
6AB = 01, CD = 01
7AB = 01, CD = 11
8AB = 01, CD = 10
9AB = 11, CD = 00
10AB = 11, CD = 01
11AB = 11, CD = 11
12AB = 11, CD = 10
13AB = 10, CD = 00
14AB = 10, CD = 01
15AB = 10, CD = 11
16AB = 10, CD = 10
14.Digital logic: gates, K-maps & flip-flopsHard
Find the minimal SOP form of F(A, B, C, D) = Σm(3, 7, 8, 9, 11, 12, 14) + d(1, 15), where d marks the don't-care conditions. How many literals L does it contain?
BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.
Thévenin equivalent of the divider
VTH = 12·6.8/(39 + 6.8) = 1.782 V
RTH = 39·6.8/(39 + 6.8) = 5.79 kΩ
Base current
KVL around the base loop; the emitter current is (β + 1)·IB.
IB = (1.782 − 0.7)/(5.79 + 151·0.68) = 9.972 µA
Collector current
IC = 150·9.972 µA = 1.496 mA
IE = 151·9.972 µA = 1.506 mA
Collector–emitter voltage
VCE = 12 − 1.496·1 − 1.506·0.68 = 9.48 V
Answer
VCE = 9.48 V
2.Diodes & transistors
Answer: RB = 1.163 kΩ
BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.
Collector current in saturation
IC(sat) = (12 − 0.2)/330 = 35.76 mA
Minimum base current
IB(min) = IC(sat)/β = 35.76/80 = 447 µA
Design base current
IB = 5·447 µA = 2235 µA
Base resistor
RB = (3.3 − 0.7)/IB = 2.6 V/2.235 mA = 1.163 kΩ
Answer
RB = 1.163 kΩ
3.Op-amp circuits
Answer: Vout = 1.5 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Inverting input follows the input
V₋ = V₊ = 0.5 V
I = V₋/R1 = 0.5/1 = 0.5 mA
Output voltage
The current through R₁ also flows through Rf.
Vout = V₋ + I·Rf = 0.5 + 0.5·2 = 1.5 V
Answer
Vout = 1.5 V
4.Op-amp circuits
Answer: If = −0.05345 mA
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Input currents
V₋ = 0, so each input resistor has its full input voltage across it.
I1 = V1/R1 = −1/22 = −0.04545 mA
I2 = V2/R2 = −0.8/100 = −0.008 mA
If = I1 + I2 = −0.05345 mA
Answer
If = −0.05345 mA
5.RC & RL transients
Answer: i = 0.004548 A
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant
τ = L/R = 10 mH / 47 Ω = 0.2128 ms
Decay of the current
i(t) = 0.5·e−1/0.2128 = 0.004548 A
Answer
i = 0.004548 A
6.RC & RL transients
Answer: t = 172.6 ms
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Initial value, final value, time constant
The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.
t = τ·ln((18 − 10)/(15.6 − 10)) = 484·ln(1.429) = 172.6 ms
Answer
t = 172.6 ms
7.Series & parallel resistors
Answer: IR2 = 0.6555 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 6 + 20 = 26 Ω
R2 ∥ 26 = 5·26/(5+26) = 4.194 Ω
Req = R1 + 4.194 = 15 + 4.194 = 19.19 Ω
Current from the source
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
IR1 = V1/Req = 15/19.19 = 0.7815 A
Current through R₂
Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.
VA = V1 − IR1·R1 = 15 − 0.7815·15 = 3.277 V
IR2 = VA/R2 = 3.277/5 = 0.6555 A
Answer
IR2 = 0.6555 A
8.Series & parallel resistors
Answer: Req = 10.61 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 10 + 30 = 40 Ω
R4 ∥ 40 = 1.905 Ω
R3 + 1.905 = 6.905 Ω
R2 ∥ 6.905 = 5.613 Ω
Req = R1 + 5.613 = 5 + 5.613 = 10.61 Ω
Answer
Req = 10.61 Ω
9.DC-DC converters
Answer: Imax = 6.284 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 14.4/24 = 0.6
Average and ripple current
Io = 14.4/2.5 = 5.76 A
ΔIL = VL·D/(L·f) = 9.6·0.6/(220·10⁻⁶·25·10³) = 1.047 A
Peak current
Imax = 5.76 + 1.047/2 = 6.284 A
Answer
Imax = 6.284 A
10.DC-DC converters
Answer: Lcrit = 7.813 µH
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 144/(48 + 144) = 0.75
Boundary condition
Set the average inductor current equal to half the ripple current and solve for L.
Lcrit = (1 − D)²·R/(2f)
Critical inductance
Lcrit = (1 − 0.75)²·50/(2200·10³) = 7.813 µH
Answer
Lcrit = 7.813 µH
11.Wheatstone bridge & strain gauges
Answer: Vab = 166.7 mV
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Node voltages
Va = 3·1250/2250 = 1.667 V
Vb = 1.5 V
Output
Vab = 166.7 mV
Answer
Vab = 166.7 mV
The linear estimate Vs·ΔR/(4R) = 187.5 mV is 12.5 % too high: a quarter bridge is not quite linear.
12.Wheatstone bridge & strain gauges
Answer: ε = 1500 µε
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Relative resistance change
ΔR/R = 1.05/350 = 0.003
Strain
ε = 0.003/2 = 0.0015 = 1500 µε
Answer
ε = 1500 µε
13.Digital logic: gates, K-maps & flip-flops
Answer: AB = 11, CD = 11
Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.
Neighbours of each 1
A 1 with a neighbouring 1 can join a group of two or more.
m15: m14, m13, m11, m7 → 0
The isolated 1
m15 = ABCD → AB = 11, CD = 11
Answer
AB = 11, CD = 11
14.Digital logic: gates, K-maps & flip-flops
Answer: L = 8
Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.
Prime implicants
The largest groups that can be formed from 1s and Xs.