Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−20 V220 Ω9.1 V3300 ΩIZ​ = ?

A 9.1 V Zener regulator is fed from 20 V through 220 Ω and supplies a 3300 Ω load. Find the Zener current IZ.

Vin = 20 VVZ = 9.1 VR = 220 ΩRL = 3300 Ω
IZ = mA
2.Diodes & transistorsHard
+−≥ 20 VR = ?3.3 V≤ 40 mA

A 3.3 V Zener regulator must supply up to 40 mA to a load. The input can drop to 20 V, and the Zener needs at least 2 mA to regulate. Find the largest series resistance Rmax that keeps it regulating.

Vin,min = 20 VVZ = 3.3 VIL,max = 40 mAIZ,min = 2 mA
Rmax = Ω
3.Op-amp circuitsMedium
−+Vout​Rf​ = ?R1​ = 100 kΩVin​

Choose the feedback resistor Rf that gives this non-inverting amplifier a voltage gain of 20.

R1 = 100 kΩAv = 20
Rf = kΩ
4.Op-amp circuitsHard
−+Vout​C = 0.47 µFVin​ = −0.6 VR = 2.2 kΩ

The integrator uses an ideal op-amp with ±15 V supplies; its output saturates at ±14 V. The capacitor is uncharged when a constant input Vin = −0.6 V is applied at t = 0. How long after t = 0 does the output reach saturation? Find t.

Vin = −0.6 VR = 2.2 kΩC = 0.47 µFVsat = ±14 V
t = ms
5.RC & RL transientsMedium
R = 20 Ωt = 0L100 mHi(t)

The inductor carries a steady current of 0.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the voltage vR across R at t = 10 ms.

i(0) = 0.5 AR = 20 ΩL = 100 mHt = 10 ms
vR = V
6.RC & RL transientsHard
+−Vs​10 Vopens at t = 0R1​ = 1 kΩR2​ = 6.8 kΩC10 µF+−vC​

The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage vC at t = 40 ms.

Vs = 10 VR1 = 1 kΩR2 = 6.8 kΩC = 10 µFt = 40 ms
vC = V
7.Series & parallel resistorsMedium
R1​ = 10 ΩIR1​R3​ = 20 Ω+−V1​30 VR2​2 ΩAR4​10 ΩB

Find the current IR1 delivered by the source, which flows through R1.

V1 = 30 VR1 = 10 ΩR2 = 2 ΩR3 = 20 ΩR4 = 10 Ω
IR1 = A
8.Series & parallel resistorsHard
R1​ = 10 ΩIR1​R3​ = 4 ΩR5​ = 30 Ω+−V1​9 VR2​30 ΩAR4​5 ΩBR6​5 Ω

Find the current IR1 delivered by the source, which flows through R1.

V1 = 9 VR1 = 10 ΩR2 = 30 ΩR3 = 4 ΩR4 = 5 ΩR5 = 30 ΩR6 = 5 Ω
IR1 = A
9.DC-DC convertersMedium
tiL​Imax​Imin​ΔI = ?DTT2T

An ideal inverting buck-boost converter turns 12 V into −8 V at 500 kHz with L = 150 µH. Find the peak-to-peak inductor ripple current ΔIL.

Vin​ = 12 VVo​ = −8 Vf = 500 kHzL = 150 µH
ΔIL = A
10.DC-DC convertersHard
+−24 VSLC = 10 µFR = 5 Ω−+−56 V

An ideal buck-boost converter turns 24 V into −56 V for a 5 Ω load at 40 kHz. The output capacitor is 10 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 24 VVo​ = −56 Vf = 40 kHzC = 10 µFR = 5 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−5 V400 Ω400 Ω400 Ω400 Ωab+−

A 400 Ω strain gauge is one arm (R₂) of a bridge with four equal 400 Ω arms and an excitation of 5 V. Find the power Pg dissipated in the gauge, in mW. Self-heating limits the excitation.

Vs = 5 VR = 400 Ω
Pg = mW
12.Wheatstone bridge & strain gaugesHard
+−V350 Ω350 Ω + ΔR350 Ω350 Ωab+−

A 350 Ω strain gauge with gauge factor 2 is bonded to a steel bar. Under load its resistance rises by 0.14 Ω. Find the strain ε in microstrain (µε).

R = 350 ΩGF = 2ΔR = 0.14 Ω
ε = µε
13.Digital logic: gates, K-maps & flip-flopsMedium
ABCD000111100001111000111302040507060120131150141819111110

Use the Karnaugh map to find the minimal sum-of-products (SOP) form of F(A, B, C, D) = Σm(1, 3, 8, 9, 10, 11, 15). How many product terms N does it have?

F(A, B, C, D) = Σm(1, 3, 8, 9, 10, 11, 15)
N =
14.Digital logic: gates, K-maps & flip-flopsHard
TQ0​Q0​TQ1​Q1​TQ2​Q2​CLKMOD-6

A synchronous mod-6 counter counts 0, 1, …, 5 and then returns to 0. It starts at 1. Which count Q (in decimal) does it show after 10 clock pulses?

Q0 = 110N = 6
Q =

3Solutions

1.Diodes & transistors

Answer: IZ = 46.79 mA

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Resistor current

IR = 10.9/220 = 49.55 mA

Load current

IL = 9.1/3300 = 2.758 mA

Zener current

IZ = 49.55 − 2.758 = 46.79 mA

Answer

IZ = 46.79 mA
2.Diodes & transistors

Answer: Rmax = 397.6 Ω

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case current

IR = 40 + 2 = 42 mA

Largest resistance

Rmax = 16.7/0.042 = 397.6 Ω

Answer

Rmax = 397.6 Ω
3.Op-amp circuits

Answer: Rf = 1900 kΩ

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain of a non-inverting amplifier

V₋ = V₊ = Vin, and the current through R₁ also flows through Rf, so Vout = Vin·(1 + Rf/R₁).

Av = 1 + Rf/R1
Rf = (20 − 1)·100 = 1900 kΩ

Answer

Rf = 1900 kΩ
4.Op-amp circuits

Answer: t = 24.13 ms

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input current and ramp rate

kΩ times µF gives milliseconds.

RC = 2.2 kΩ · 0.47 µF = 1.034 ms
ramp rate = −Vin/(RC) = −(−0.6)/1.034 = 0.5803 V/ms

Time to saturation

|Vin|·t/(RC) = Vsat → t = Vsat·RC/|Vin| = 14·1.034/0.6 = 24.13 ms

Answer

t = 24.13 ms
5.RC & RL transients

Answer: vR = 1.353 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant

τ = L/R = 100 mH / 20 Ω = 5 ms

Decay of the current

i(t) = 0.5·e−10/5 = 0.06767 A
vR = R·i = 20·0.06767 = 1.353 V

Answer

vR = 1.353 V
6.RC & RL transients

Answer: vC = 4.841 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial capacitor voltage

In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.

vC(0) = 10·6.8/(1 + 6.8) = 8.718 V

Time constant after the switch opens

τ = R2·C = 6.8·10 = 68 ms

Discharge

vC(t) = 8.718·e−40/68 = 4.841 V

Answer

vC = 4.841 V
7.Series & parallel resistors

Answer: IR1 = 2.526 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 10 ΩR3​ = 20 Ω+−V1​30 VR2​2 ΩAR4​10 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 20 + 10 = 30 Ω
R2 ∥ 30 = 2·30/(2+30) = 1.875 Ω
Req = R1 + 1.875 = 10 + 1.875 = 11.88 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 30/11.88 = 2.526 A

Answer

IR1 = 2.526 A
8.Series & parallel resistors

Answer: IR1 = 0.5439 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 10 ΩR3​ = 4 ΩR5​ = 30 Ω+−V1​9 VR2​30 ΩAR4​5 ΩBR6​5 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 30 + 5 = 35 Ω
R4 ∥ 35 = 4.375 Ω
R3 + 4.375 = 8.375 Ω
R2 ∥ 8.375 = 6.547 Ω
Req = R1 + 6.547 = 10 + 6.547 = 16.55 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 9/16.55 = 0.5439 A

Answer

IR1 = 0.5439 A
9.DC-DC converters

Answer: ΔIL = 0.064 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 8/(12 + 8) = 0.4

Inductor voltage during the on-time

While S is on, the inductor sits directly across Vin.

VL = 12 V

Ripple current

ΔIL = VL·D/(L·f) = 12·0.4/(150·10⁻⁶·500·10³) = 0.064 A

Answer

ΔIL = 0.064 A
10.DC-DC converters

Answer: ΔVo = 19600 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 56/(24 + 56) = 0.7

Load current

Io = 56/5 = 11.2 A

Output ripple

ΔVo = 11.2·0.7/(40·10³·10·10⁻⁶) = 19600 mV

Answer

ΔVo = 19600 mV
11.Wheatstone bridge & strain gauges

Answer: Pg = 15.63 mW

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Voltage across the gauge

V = 5/2 = 2.5 V

Power

Pg = 2.5²/400 = 15.63 mW

Answer

Pg = 15.63 mW
12.Wheatstone bridge & strain gauges

Answer: ε = 200 µε

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Relative resistance change

ΔR/R = 0.14/350 = 0.0004

Strain

ε = 0.0004/2 = 0.0002 = 200 µε

Answer

ε = 200 µε
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 3

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

ABCD000111100001111000111302040507060120131150141819111110

Group the 1s

Every group is a rectangle of 2ᵏ cells; edge cells are neighbours of the cells on the opposite edge.

B′D
ACD
AB′

Minimal SOP form

F = B′D + ACD + AB′
N = 3

Answer

N = 3
14.Digital logic: gates, K-maps & flip-flops

Answer: Q = 5

Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.

Full cycles

Every 6 pulses bring the counter back to the same state.

10 = 1·6 + 4

Count after the remaining pulses

Q = (1 + 4) mod 6 = 5
Q = 101₂

Answer

Q = 5

ExamProblems · examproblems.com/courses/electronics-1