Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−24 V150 Ω6.2 V2200 ΩIZ​ = ?

A 6.2 V Zener regulator is fed from 24 V through 150 Ω and supplies a 2200 Ω load. Find the Zener current IZ.

Vin = 24 VVZ = 6.2 VR = 150 ΩRL = 2200 Ω
IZ = mA
2.Diodes & transistorsHard
RC​ = 100 Ωβ = 80VCC​ = 24 V3.3 VRB​ = ?

An NPN transistor with β = 80 switches a 100 Ω load resistor connected between VCC = 24 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. Find the largest base resistor RB, in kΩ, that still drives the transistor just into saturation.

VCC = 24 VRC = 100 Ωβ = 80Vin = 3.3 VVBE = 0.7 VVCE(sat) = 0.2 V
RB = kΩ
3.Op-amp circuitsMedium
−+Vout​R2​ = 22 kΩV1​ = 0.2 VR1​ = 47 kΩV2​ = 2.2 VR3​ = 47 kΩR4​ = 22 kΩ

The difference amplifier uses an ideal op-amp with ±15 V supplies, with R3 = R1 and R4 = R2. Find the voltage V− at the inverting input.

V1 = 0.2 VV2 = 2.2 VR1 = R3 = 47 kΩR2 = R4 = 22 kΩ
V− = V
4.Op-amp circuitsHard
−+Vout​Rf​ = 2 kΩV1​ = −0.3 VR1​ = 22 kΩV2​ = −1.9 VR2​ = 4.7 kΩIf​

The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the current If through the feedback resistor, flowing towards the output.

V1 = −0.3 VV2 = −1.9 VR1 = 22 kΩR2 = 4.7 kΩRf = 2 kΩ
If = mA
5.RC & RL transientsMedium
+−Vs​24 Vt = 0R = 50 ΩL10 mHi(t)

The inductor carries no current before the switch closes at t = 0. Find the energy W stored in the inductor at t = 1 ms, in mJ.

Vs = 24 VR = 50 ΩL = 10 mHt = 1 ms
W = mJ
6.RC & RL transientsHard
+−Vs​10 VR1​ = 20 ΩR2​ = 5 Ωopens at t = 0L220 mHi(t)

The switch across R2 has been closed for a long time, so the inductor current is steady. At t = 0 the switch opens. Find the inductor current i at t = 15 ms.

Vs = 10 VR1 = 20 ΩR2 = 5 ΩL = 220 mHt = 15 ms
i = A
7.Series & parallel resistorsMedium
R1​ = 10 ΩR3​ = 2 Ω+−V1​12 VR2​12 ΩAR4​10 ΩB

Find the equivalent resistance Req seen by the source V1.

V1 = 12 VR1 = 10 ΩR2 = 12 ΩR3 = 2 ΩR4 = 10 Ω
Req = Ω
8.Series & parallel resistorsHard
R1​ = 3 ΩR3​ = 5 ΩR5​ = 15 Ω+−V1​18 VR2​5 ΩIR2​AR4​25 ΩBR6​15 Ω

Find the current IR2 through R2.

V1 = 18 VR1 = 3 ΩR2 = 5 ΩR3 = 5 ΩR4 = 25 ΩR5 = 15 ΩR6 = 15 Ω
IR2 = A
9.DC-DC convertersMedium
+−36 VLSCR = 10 Ω+−144 V

An ideal boost converter turns 36 V into 144 V for a 10 Ω load. Find the average inductor current IL.

Vin​ = 36 VVo​ = 144 VR = 10 Ω
IL = A
10.DC-DC convertersHard
tvo​Vo​ΔV = ?DTT2T

A buck converter turns 24 V into 18 V for a 10 Ω load at 100 kHz, with L = 22 µH and C = 22 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 24 VVo​ = 18 Vf = 100 kHzL = 22 µHC = 22 µF
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−6 V470 Ω470 Ω + ΔR470 Ω470 Ωab+−Vab​ = ?

A bridge has four 470 Ω arms and Vs = 6 V. The sensor R₂ increases by ΔR = 1.88 Ω. Using the small-change approximation, find the output Vab in mV.

Vs = 6 VR = 470 ΩΔR = 1.88 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−5 V1000 Ω − ΔR1000 Ω + ΔR1000 Ω + ΔR1000 Ω − ΔRab+−Vo​ = ?

A load cell (a full bridge of strain gauges) has a rated output of 2.5 mV/V at its rated load of 200 kg. It is excited with 5 V. Find its output Vo under a load of 100 kg.

2.5 mV/VFrated = 200 kgVs = 5 VF = 100 kg
Vo = mV
13.Digital logic: gates, K-maps & flip-flopsMedium
MUXC′I0​0I1​0I2​CI3​ABS1​S0​F

A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = C′, I₁ = 0, I₂ = 0, I₃ = C. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.

I₀ = C′I₁ = 0I₂ = 0I₃ = C
N =
14.Digital logic: gates, K-maps & flip-flopsHard
CLKJK123456

A positive-edge-triggered JK flip-flop starts with Q = 0 and receives the inputs shown. Click the first clock edge at which Q goes from 1 back to 0.

Q₀ = 0JK
  1. 1clock edge 1
  2. 2clock edge 2
  3. 3clock edge 3
  4. 4clock edge 4
  5. 5clock edge 5
  6. 6clock edge 6

3Solutions

1.Diodes & transistors

Answer: IZ = 115.8 mA

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Resistor current

IR = 17.8/150 = 118.7 mA

Load current

IL = 6.2/2200 = 2.818 mA

Zener current

IZ = 118.7 − 2.818 = 115.8 mA

Answer

IZ = 115.8 mA
2.Diodes & transistors

Answer: RB = 0.8739 kΩ

BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.

Collector current in saturation

IC(sat) = (24 − 0.2)/100 = 238 mA

Minimum base current

IB(min) = IC(sat)/β = 238/80 = 2975 µA

Base resistor

RB = (3.3 − 0.7)/IB = 2.6 V/2.975 mA = 0.8739 kΩ

Answer

RB = 0.8739 kΩ

Any smaller base resistor also saturates the transistor; in practice you pick one a few times smaller.

3.Op-amp circuits

Answer: V− = 0.7014 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Voltage at the inputs

R₃ and R₄ carry the same current, so they form a voltage divider; feedback makes V₋ = V₊.

V₊ = V2·R4/(R3 + R4) = 2.2·22/(47 + 22) = 0.7014 V
V₋ = V₊

Answer

V− = 0.7014 V
4.Op-amp circuits

Answer: If = −0.4179 mA

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input currents

V₋ = 0, so each input resistor has its full input voltage across it.

I1 = V1/R1 = −0.3/22 = −0.01364 mA
I2 = V2/R2 = −1.9/4.7 = −0.4043 mA
If = I1 + I2 = −0.4179 mA

Answer

If = −0.4179 mA
5.RC & RL transients

Answer: W = 1.137 mJ

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 10 mH / 50 Ω = 0.2 ms
i(∞) = Vs/R = 24/50 = 0.48 A

Current at the given time

i(t) = 0.48·(1 − e−1/0.2) = 0.4768 A

Stored energy

W = ½·L·i² = ½·10·0.4768² = 1.137 mJ

Answer

W = 1.137 mJ
6.RC & RL transients

Answer: i = 0.4182 A

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

Before t = 0 the closed switch bypasses R₂; afterwards R₁ and R₂ are both in the loop.

i(0) = 10/20 = 0.5 A
i(∞) = 10/(20 + 5) = 0.4 A
τ = L/R = 220/25 = 8.8 ms
i(t) = 0.4 + (0.5 − 0.4)·e−t/τ

Current at the given time

i(15) = 0.4 + (0.1)·e−15/8.8 = 0.4182 A

Answer

i = 0.4182 A
7.Series & parallel resistors

Answer: Req = 16 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 10 ΩR3​ = 2 Ω+−V1​12 VR2​12 ΩAR4​10 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 2 + 10 = 12 Ω
R2 ∥ 12 = 12·12/(12+12) = 6 Ω
Req = R1 + 6 = 10 + 6 = 16 Ω

Answer

Req = 16 Ω
8.Series & parallel resistors

Answer: IR2 = 2.044 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 3 ΩR3​ = 5 ΩR5​ = 15 Ω+−V1​18 VR2​5 ΩAR4​25 ΩBR6​15 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 15 + 15 = 30 Ω
R4 ∥ 30 = 13.64 Ω
R3 + 13.64 = 18.64 Ω
R2 ∥ 18.64 = 3.942 Ω
Req = R1 + 3.942 = 3 + 3.942 = 6.942 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 18/6.942 = 2.593 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

VA = V1 − IR1·R1 = 18 − 2.593·3 = 10.22 V
IR2 = VA/R2 = 10.22/5 = 2.044 A

Answer

IR2 = 2.044 A
9.DC-DC converters

Answer: IL = 57.6 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 1 − 36/144 = 0.75

Load current

Io = 144/10 = 14.4 A

Inductor current

IL = Io/(1 − D) = 14.4/0.25 = 57.6 A

Answer

IL = 57.6 A
10.DC-DC converters

Answer: ΔVo = 116.2 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 18/24 = 0.75

Inductor ripple current

ΔIL = (24 − 18)·0.75/(22·10⁻⁶·100·10³) = 2.045 A

Output ripple

ΔVo = 2.045/(8·100·10³·22·10⁻⁶) = 116.2 mV

Answer

ΔVo = 116.2 mV
11.Wheatstone bridge & strain gauges

Answer: Vab = 6 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Relative change

ΔR/R = 1.88/470 = 0.004

Linearised output

Vab ≈ 6·0.004/4 = 6 mV

Answer

Vab = 6 mV

The exact value is 5.988 mV; the approximation is good while ΔR/R is small.

12.Wheatstone bridge & strain gauges

Answer: Vo = 6.25 mV

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Full-scale output

2.5·5 = 12.5 mV

Output at this load

Vo = 12.5·100/200 = 6.25 mV

Answer

Vo = 6.25 mV
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 2

Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.

Output expression

F = A′B′C′ + ABC

Rows with F = 1

ABC = 000, 111
N = 2

Answer

N = 2
14.Digital logic: gates, K-maps & flip-flops

Answer: clock edge 6

Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.

Q after every edge

A JK flip-flop: 00 holds, 01 resets (Q = 0), 10 sets (Q = 1), 11 toggles.

1: J = 0, K = 1 → Q = 0
2: J = 0, K = 1 → Q = 0
3: J = 0, K = 0 → Q = 0
4: J = 0, K = 1 → Q = 0
5: J = 1, K = 0 → Q = 1
6: J = 1, K = 1 → Q = 0

First change from 1 to 0

clock edge 6

Answer

clock edge 6

ExamProblems · examproblems.com/courses/electronics-1