Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−12 V150 Ω9.1 V2200 ΩIZ​ = ?

A 9.1 V Zener regulator is fed from 12 V through 150 Ω and supplies a 2200 Ω load. Find the Zener current IZ.

Vin = 12 VVZ = 9.1 VR = 150 ΩRL = 2200 Ω
IZ = mA
2.Diodes & transistorsHard
RC​ = 1 kΩβ = 150VCC​ = 5 V3.3 VRB​ = ?

An NPN transistor with β = 150 switches a 1 kΩ load resistor connected between VCC = 5 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. For reliable switching, design for a base current 5 times the minimum needed for saturation. Find RB in kΩ.

VCC = 5 VRC = 1 kΩβ = 150Vin = 3.3 VVBE = 0.7 VVCE(sat) = 0.2 Voverdrive = 5
RB = kΩ
3.Op-amp circuitsMedium
−+Vout​Rf​ = 100 kΩR1​ = 100 kΩVin​ = 1.8 V

The op-amp is ideal and runs from ±15 V supplies. Find the output voltage Vout.

Vin = 1.8 VR1 = 100 kΩRf = 100 kΩ
Vout = V
4.Op-amp circuitsHard
−+Vout​Rf​ = 4.7 kΩV1​ = 1.8 VR1​ = 1 kΩV2​ = 1.5 VR2​ = 22 kΩ

The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the output voltage Vout.

V1 = 1.8 VV2 = 1.5 VR1 = 1 kΩR2 = 22 kΩRf = 4.7 kΩ
Vout = V
5.RC & RL transientsMedium
+−Vs​6 Vt = 0R = 33 ΩL220 mHi(t)

The inductor carries no current before the switch closes at t = 0. How long after the switch closes does the current reach 99% of its final value? Find t.

Vs = 6 VR = 33 ΩL = 220 mH
t = ms
6.RC & RL transientsHard
+−Vs​9 Vt = 0R = 10 kΩC?+−vC​

A timer starts charging an uncharged capacitor through a resistor from a 9 V supply at t = 0. It must trigger when the capacitor voltage reaches 4.5 V, exactly 10 ms after the start. With R = 10 kΩ, find the capacitance C needed.

Vs = 9 VVth = 4.5 VT = 10 msR = 10 kΩ
C = µF
7.Series & parallel resistorsMedium
R1​ = 8 ΩIR1​R3​ = 4 Ω+−V1​10 VR2​4 ΩAR4​3 ΩB

Find the current IR1 delivered by the source, which flows through R1.

V1 = 10 VR1 = 8 ΩR2 = 4 ΩR3 = 4 ΩR4 = 3 Ω
IR1 = A
8.Series & parallel resistorsHard
R1​ = 30 ΩR3​ = 12 ΩR5​ = 20 Ω+−V1​5 VR2​5 ΩAR4​6 ΩBR6​8 Ω

Find the equivalent resistance Req seen by the source V1.

V1 = 5 VR1 = 30 ΩR2 = 5 ΩR3 = 12 ΩR4 = 6 ΩR5 = 20 ΩR6 = 8 Ω
Req = Ω
9.DC-DC convertersMedium
tiL​Imax​Imin​ΔI = ?DTT2T

An ideal buck converter turns 24 V into 14.4 V at 200 kHz with L = 10 µH. Find the peak-to-peak inductor ripple current ΔIL.

Vin​ = 24 VVo​ = 14.4 Vf = 200 kHzL = 10 µH
ΔIL = A
10.DC-DC convertersHard
+−9 VSLC = 100 µFR = 25 Ω−+−3 V

An ideal buck-boost converter turns 9 V into −3 V for a 25 Ω load at 200 kHz. The output capacitor is 100 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 9 VVo​ = −3 Vf = 200 kHzC = 100 µFR = 25 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−2 V500 Ω500 Ω + ΔR500 Ω500 Ωab+−Vab​ = ?

A bridge has four 500 Ω arms and Vs = 2 V. The sensor R₂ increases by ΔR = 5 Ω. Using the small-change approximation, find the output Vab in mV.

Vs = 2 VR = 500 ΩΔR = 5 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−5 V1000 Ω1000 Ω + ΔR1000 Ω1000 Ωab+−1.575 mV

A strain gauge (GF = 2.1) on a member with E = 210 GPa forms a quarter bridge excited with 5 V. The output reads 1.575 mV. Find the axial stress σ in MPa.

Vs = 5 VGF = 2.1Vo = 1.575 mVE = 210 GPa
σ = MPa
13.Digital logic: gates, K-maps & flip-flopsMedium
ABC000111100101324576

Simplify F = ABC + AB′ + A′BC′ to its minimal sum-of-products form. How many literals L does the simplified expression contain?

F = ABC + AB′ + A′BC′
L =
14.Digital logic: gates, K-maps & flip-flopsHard
DQ3​Q3​DQ2​Q2​DQ1​Q1​DQ0​Q0​CLKRING

A 4-bit ring counter Q₃Q₂Q₁Q₀ starts at 1100. At every clock edge the bits shift one place to the right (Q₃ → Q₂ → Q₁ → Q₀) and Q₃ receives Q₀. Give the state Q = Q₃Q₂Q₁Q₀ as a decimal number after 3 clock edges.

Q₃Q₂Q₁Q₀ = 11003
Q =

3Solutions

1.Diodes & transistors

Answer: IZ = 15.2 mA

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Resistor current

IR = 2.9/150 = 19.33 mA

Load current

IL = 9.1/2200 = 4.136 mA

Zener current

IZ = 19.33 − 4.136 = 15.2 mA

Answer

IZ = 15.2 mA
2.Diodes & transistors

Answer: RB = 16.25 kΩ

BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.

Collector current in saturation

IC(sat) = (5 − 0.2)/1000 = 4.8 mA

Minimum base current

IB(min) = IC(sat)/β = 4.8/150 = 32 µA

Design base current

IB = 5·32 µA = 160 µA

Base resistor

RB = (3.3 − 0.7)/IB = 2.6 V/0.16 mA = 16.25 kΩ

Answer

RB = 16.25 kΩ
3.Op-amp circuits

Answer: Vout = 3.6 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Inverting input follows the input

V₋ = V₊ = 1.8 V
I = V₋/R1 = 1.8/100 = 0.018 mA

Output voltage

The current through R₁ also flows through Rf.

Vout = V₋ + I·Rf = 1.8 + 0.018·100 = 3.6 V

Answer

Vout = 3.6 V
4.Op-amp circuits

Answer: Vout = −8.78 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input currents

V₋ = 0, so each input resistor has its full input voltage across it.

I1 = V1/R1 = 1.8/1 = 1.8 mA
I2 = V2/R2 = 1.5/22 = 0.06818 mA
If = I1 + I2 = 1.868 mA

Output voltage

Vout = −Rf·If = −4.7·1.868 = −8.78 V

Answer

Vout = −8.78 V
5.RC & RL transients

Answer: t = 30.7 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 220 mH / 33 Ω = 6.667 ms
i(∞) = Vs/R = 6/33 = 0.1818 A

Solve for the time

0.99 = 1 − e−t/τ → t = −τ·ln(1 − 0.99)
t = −6.667·ln(0.01) = 30.7 ms

Answer

t = 30.7 ms
6.RC & RL transients

Answer: C = 1.443 µF

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Required time constant

4.5 = 9·(1 − e−10/τ) → τ = 10/ln(9/(9 − 4.5))
τ = 10/0.6931 = 14.43 ms

Capacitance

kΩ times µF gives milliseconds.

C = τ/R = 14.43/10 = 1.443 µF

Answer

C = 1.443 µF
7.Series & parallel resistors

Answer: IR1 = 0.9483 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 8 ΩR3​ = 4 Ω+−V1​10 VR2​4 ΩAR4​3 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 4 + 3 = 7 Ω
R2 ∥ 7 = 4·7/(4+7) = 2.545 Ω
Req = R1 + 2.545 = 8 + 2.545 = 10.55 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 10/10.55 = 0.9483 A

Answer

IR1 = 0.9483 A
8.Series & parallel resistors

Answer: Req = 33.86 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 30 ΩR3​ = 12 ΩR5​ = 20 Ω+−V1​5 VR2​5 ΩAR4​6 ΩBR6​8 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 20 + 8 = 28 Ω
R4 ∥ 28 = 4.941 Ω
R3 + 4.941 = 16.94 Ω
R2 ∥ 16.94 = 3.861 Ω
Req = R1 + 3.861 = 30 + 3.861 = 33.86 Ω

Answer

Req = 33.86 Ω
9.DC-DC converters

Answer: ΔIL = 2.88 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 14.4/24 = 0.6

Inductor voltage during the on-time

While S is on, the inductor sits between Vin and Vo.

VL = 24 − 14.4 = 9.6 V

Ripple current

ΔIL = VL·D/(L·f) = 9.6·0.6/(10·10⁻⁶·200·10³) = 2.88 A

Answer

ΔIL = 2.88 A
10.DC-DC converters

Answer: ΔVo = 1.5 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 3/(9 + 3) = 0.25

Load current

Io = 3/25 = 0.12 A

Output ripple

ΔVo = 0.12·0.25/(200·10³·100·10⁻⁶) = 1.5 mV

Answer

ΔVo = 1.5 mV
11.Wheatstone bridge & strain gauges

Answer: Vab = 5 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Relative change

ΔR/R = 5/500 = 0.01

Linearised output

Vab ≈ 2·0.01/4 = 5 mV

Answer

Vab = 5 mV

The exact value is 4.975 mV; the approximation is good while ΔR/R is small.

12.Wheatstone bridge & strain gauges

Answer: σ = 126 MPa

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Strain

ε = 4·0.001575/(5·2.1) = 0.0006

Stress

σ = 210·10³ MPa·0.0006 = 126 MPa

Answer

σ = 126 MPa
13.Digital logic: gates, K-maps & flip-flops

Answer: L = 7

Boolean algebra: the rules that simplify expressions are X + X′ = 1 and X·X′ = 0, X + X = X, absorption X + X·Y = X, the combining rule X·Y + X·Y′ = X, X + X′Y = X + Y and the consensus theorem XY + X′Z + YZ = XY + X′Z. De Morgan's laws turn (X·Y)′ into X′ + Y′ and (X + Y)′ into X′·Y′. A Karnaugh map applies these rules graphically: every group of two neighbouring cells is one use of XY + XY′ = X.

Minterms of the expression

ABC → m(7)
AB′ → m(4, 5)
A′BC′ → m(2)
ABC00011110010001031214151706

Group and read off

F = AC + AB′ + A′BC′

Count the literals

L = 7

Answer

L = 7
14.Digital logic: gates, K-maps & flip-flops

Answer: Q = 9

Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.

State after every edge

1100 → 0110 → 0011 → 1001

Decimal value

1001₂ = 9

Answer

Q = 9

ExamProblems · examproblems.com/courses/electronics-1