Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−24 VR = ?4 × 2 V10 mA

4 red LEDs (forward voltage 2 V each) are connected in series with a resistor to a 24 V supply. Find the resistance R that sets the current to 10 mA.

Vs = 24 VVF = 2 Vn = 4I = 10 mA
R = Ω
2.Diodes & transistorsHard
+−≤ 21 V100 Ω9.1 V

A 9.1 V Zener regulator has a 100 Ω series resistor. The input can rise to 21 V, and the load may be disconnected. Find the largest power PZ,max the Zener must dissipate.

Vin,max = 21 VVZ = 9.1 VR = 100 Ω
PZ,max = mW
3.Op-amp circuitsMedium
−+Vout​Rf​ = 100 kΩVin​R1​ = 2 kΩ

The op-amp is ideal and runs from ±15 V supplies; its output saturates at ±13 V. The inverting amplifier is driven by a sine wave. Find the largest input amplitude Vin,max (peak value) for which the output does not clip.

R1 = 2 kΩRf = 100 kΩVsat = ±13 V
Vin,max = V
4.Op-amp circuitsHard
Vin​V1​Vout​stage 1: invertingR1​ = 2 kΩRf1​ = 2 kΩstage 2: non-invertingR2​ = 100 kΩRf2​ = 2 kΩ

Two ideal op-amp stages are connected in cascade: an inverting amplifier (R1, Rf1) followed by a non-inverting amplifier (R2 to ground, Rf2 in the feedback). Both run from ±15 V supplies. The input is Vin = −0.95 V. Find the output voltage Vout.

R1 = 2 kΩRf1 = 2 kΩR2 = 100 kΩRf2 = 2 kΩVin = −0.95 V
Vout = V
5.RC & RL transientsMedium
R = 20 Ωt = 0L10 mHi(t)

The inductor carries a steady current of 0.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the voltage vR across R at t = 1 ms.

i(0) = 0.5 AR = 20 ΩL = 10 mHt = 1 ms
vR = V
6.RC & RL transientsHard
+−Vs​20 Vt = 0R = 10 kΩC22 µF+−vC​vC​(0) = 12 V

Just before the switch closes at t = 0, the capacitor holds 12 V with the polarity shown. Find the capacitor voltage vC at t = 250 ms.

Vs = 20 VR = 10 kΩC = 22 µFvC(0) = 12 Vt = 250 ms
vC = V
7.Series & parallel resistorsMedium
R1​ = 4 ΩIR1​R3​ = 10 Ω+−V1​9 VR2​15 ΩAR4​2 ΩB

Find the current IR1 delivered by the source, which flows through R1.

V1 = 9 VR1 = 4 ΩR2 = 15 ΩR3 = 10 ΩR4 = 2 Ω
IR1 = A
8.Series & parallel resistorsHard
R1​ = 20 ΩR3​ = 10 ΩR5​ = 5 Ω+−V1​15 VR2​30 ΩAR4​3 ΩBR6​12 Ω

Find the equivalent resistance Req seen by the source V1.

V1 = 15 VR1 = 20 ΩR2 = 30 ΩR3 = 10 ΩR4 = 3 ΩR5 = 5 ΩR6 = 12 Ω
Req = Ω
9.DC-DC convertersMedium
+−24 VSL = ?CR+−14.4 V

An ideal buck converter turns 24 V into 14.4 V at a switching frequency of 40 kHz. Find the inductance L that keeps the peak-to-peak inductor ripple current at 0.2 A.

Vin​ = 24 VVo​ = 14.4 Vf = 40 kHzΔIL = 0.2 A
L = µH
10.DC-DC convertersHard
+−15 VLSC = 22 µFR = 8 Ω+−30 V

An ideal boost converter turns 15 V into 30 V for an 8 Ω load at 100 kHz. The output capacitor is 22 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 15 VVo​ = 30 Vf = 100 kHzC = 22 µFR = 8 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−5 V200 Ω200 Ω + ΔR200 Ω200 Ωab+−Vab​ = ?

A bridge has four 200 Ω arms and Vs = 5 V. The sensor R₂ increases by ΔR = 50 Ω. Find the exact output Vab in mV.

Vs = 5 VR = 200 ΩΔR = 50 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−3 V120 Ω120 Ω + ΔR120 Ω120 Ωab+−Vo​

A quarter bridge (one active gauge, GF = 2.12) is excited with 3 V. The largest strain to be measured is 400 µε, and it must give 5 V at the input of an analogue-to-digital converter. Find the amplifier gain G.

Vs = 3 VGF = 2.12εmax = 400 µεVFS = 5 V
G =
13.Digital logic: gates, K-maps & flip-flopsMedium
MUXCI0​0I1​CI2​CI3​ABS1​S0​F

A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = C, I₁ = 0, I₂ = C, I₃ = C. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.

I₀ = CI₁ = 0I₂ = CI₃ = C
N =
14.Digital logic: gates, K-maps & flip-flopsHard
CLKJK1234567

A positive-edge-triggered JK flip-flop starts with Q = 0 and receives the inputs shown at 7 rising clock edges. How many times N does Q change state?

Q₀ = 0JK
N =

3Solutions

1.Diodes & transistors

Answer: R = 1600 Ω

LED and diode circuits: a forward-biased LED drops roughly its forward voltage VF (about 2 V for red, 3 V for blue or white), whatever the current. A series resistor sets the current: R = (Vs − n·VF)/I for n LEDs in series. With a more exact diode model V = V₀ + I·rd, the operating point is where the diode line meets the load line I = (Vs − V)/R, so I = (Vs − V₀)/(R + rd).

Voltage across the resistor

VR = 24 − 4·2 = 16 V

Resistance

R = 16/0.01 = 1600 Ω

Answer

R = 1600 Ω

The resistor dissipates 160 mW.

2.Diodes & transistors

Answer: PZ,max = 1083 mW

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case Zener current

IZ = 11.9/100 = 119 mA

Zener power

PZ = 9.1·119 = 1083 mW

Answer

PZ,max = 1083 mW
3.Op-amp circuits

Answer: Vin,max = 0.26 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain

|Av| = Rf/R1 = 100/2 = 50

Largest input before clipping

Vin,max = Vsat/|Av| = 13/50 = 0.26 V

Answer

Vin,max = 0.26 V
4.Op-amp circuits

Answer: Vout = 0.969 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain of each stage

A1 = −Rf1/R1 = −2/2 = −1
A2 = 1 + Rf2/R2 = 1 + 2/100 = 1.02

Stage by stage

V1 = −1·(−0.95) = 0.95 V
Vout = 1.02·0.95 = 0.969 V

Answer

Vout = 0.969 V
5.RC & RL transients

Answer: vR = 1.353 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant

τ = L/R = 10 mH / 20 Ω = 0.5 ms

Decay of the current

i(t) = 0.5·e−1/0.5 = 0.06767 A
vR = R·i = 20·0.06767 = 1.353 V

Answer

vR = 1.353 V
6.RC & RL transients

Answer: vC = 17.43 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 12 V, vC(∞) = Vs = 20 V
τ = R·C = 10 kΩ · 22 µF = 220 ms
vC(t) = 20 + (12 − 20)·e−t/τ

Voltage at the given time

vC(250) = 20 + (−8)·e−250/220 = 17.43 V

Answer

vC = 17.43 V
7.Series & parallel resistors

Answer: IR1 = 0.8437 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 4 ΩR3​ = 10 Ω+−V1​9 VR2​15 ΩAR4​2 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 10 + 2 = 12 Ω
R2 ∥ 12 = 15·12/(15+12) = 6.667 Ω
Req = R1 + 6.667 = 4 + 6.667 = 10.67 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 9/10.67 = 0.8437 A

Answer

IR1 = 0.8437 A
8.Series & parallel resistors

Answer: Req = 28.85 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 20 ΩR3​ = 10 ΩR5​ = 5 Ω+−V1​15 VR2​30 ΩAR4​3 ΩBR6​12 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 5 + 12 = 17 Ω
R4 ∥ 17 = 2.55 Ω
R3 + 2.55 = 12.55 Ω
R2 ∥ 12.55 = 8.848 Ω
Req = R1 + 8.848 = 20 + 8.848 = 28.85 Ω

Answer

Req = 28.85 Ω
9.DC-DC converters

Answer: L = 720 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 14.4/24 = 0.6

Inductance

L = 9.6·0.6/(0.2·40·10³) = 720 µH

Answer

L = 720 µH
10.DC-DC converters

Answer: ΔVo = 852.3 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 1 − 15/30 = 0.5

Load current

Io = 30/8 = 3.75 A

Output ripple

ΔVo = 3.75·0.5/(100·10³·22·10⁻⁶) = 852.3 mV

Answer

ΔVo = 852.3 mV
11.Wheatstone bridge & strain gauges

Answer: Vab = 277.8 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Node voltages

Va = 5·250/450 = 2.778 V
Vb = 2.5 V

Output

Vab = 277.8 mV

Answer

Vab = 277.8 mV

The linear estimate Vs·ΔR/(4R) = 312.5 mV is 12.5 % too high: a quarter bridge is not quite linear.

12.Wheatstone bridge & strain gauges

Answer: G = 7862

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Bridge output at full scale

Vo = 0.636 mV

Gain

G = 5/0.000636 = 7862

Answer

G = 7862
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 3

Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.

Output expression

F = A′B′C + AB′C + ABC

Rows with F = 1

ABC = 001, 101, 111
N = 3

Answer

N = 3
14.Digital logic: gates, K-maps & flip-flops

Answer: N = 2

Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.

Q after every edge

A JK flip-flop: 00 holds, 01 resets (Q = 0), 10 sets (Q = 1), 11 toggles.

1: J = 0, K = 1 → Q = 0
2: J = 1, K = 0 → Q = 1
3: J = 1, K = 0 → Q = 1
4: J = 0, K = 0 → Q = 1
5: J = 1, K = 0 → Q = 1
6: J = 0, K = 1 → Q = 0
7: J = 0, K = 0 → Q = 0

Count the changes

0 → 0 → 1 → 1 → 1 → 1 → 0 → 0
N = 2

Answer

N = 2

ExamProblems · examproblems.com/courses/electronics-1