Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−24 VR = ?2 × 3 V10 mA

2 white LEDs (forward voltage 3 V each) are connected in series with a resistor to a 24 V supply. Find the resistance R that sets the current to 10 mA.

Vs = 24 VVF = 3 Vn = 2I = 10 mA
R = Ω
2.Diodes & transistorsHard
+−≥ 24 VR = ?5.6 V≤ 20 mA

A 5.6 V Zener regulator must supply up to 20 mA to a load. The input can drop to 24 V, and the Zener needs at least 1 mA to regulate. Find the largest series resistance Rmax that keeps it regulating.

Vin,min = 24 VVZ = 5.6 VIL,max = 20 mAIZ,min = 1 mA
Rmax = Ω
3.Op-amp circuitsMedium
−+Vout​Rf​ = ?R1​ = 10 kΩVin​

Choose the feedback resistor Rf that gives this non-inverting amplifier a voltage gain of 25.

R1 = 10 kΩAv = 25
Rf = kΩ
4.Op-amp circuitsHard
Vin​V1​Vout​stage 1: invertingR1​ = 2 kΩRf1​ = 4.7 kΩstage 2: non-invertingR2​ = 22 kΩRf2​ = 4.7 kΩ

Two ideal op-amp stages are connected in cascade: an inverting amplifier (R1, Rf1) followed by a non-inverting amplifier (R2 to ground, Rf2 in the feedback). Both run from ±15 V supplies. The input is Vin = −0.15 V. Find the output voltage Vout.

R1 = 2 kΩRf1 = 4.7 kΩR2 = 22 kΩRf2 = 4.7 kΩVin = −0.15 V
Vout = V
5.RC & RL transientsMedium
+−Vs​20 Vt = 0R = 50 ΩL68 mHi(t)

The inductor carries no current before the switch closes at t = 0. Find the voltage vL across the inductor at t = 1 ms.

Vs = 20 VR = 50 ΩL = 68 mHt = 1 ms
vL = V
6.RC & RL transientsHard
+−Vs​6 VR1​ = 33 ΩR2​ = 47 Ωopens at t = 0L22 mHi(t)

The switch across R2 has been closed for a long time, so the inductor current is steady. At t = 0 the switch opens. How long after t = 0 does the inductor current reach 0.139 A? Find t.

Vs = 6 VR1 = 33 ΩR2 = 47 ΩL = 22 mH
t = ms
7.Series & parallel resistorsMedium
R1​ = 15 ΩR3​ = 5 Ω+−V1​9 VR2​6 ΩAR4​10 ΩB

Find the equivalent resistance Req seen by the source V1.

V1 = 9 VR1 = 15 ΩR2 = 6 ΩR3 = 5 ΩR4 = 10 Ω
Req = Ω
8.Series & parallel resistorsHard
R1​ = 30 ΩR3​ = 15 ΩR5​ = 12 Ω+−V1​30 VR2​20 ΩIR2​AR4​25 ΩBR6​12 Ω

Find the current IR2 through R2.

V1 = 30 VR1 = 30 ΩR2 = 20 ΩR3 = 15 ΩR4 = 25 ΩR5 = 12 ΩR6 = 12 Ω
IR2 = A
9.DC-DC convertersMedium
tiL​Imax​Imin​ΔI = ?DTT2T

An ideal buck converter turns 48 V into 33.6 V at 20 kHz with L = 220 µH. Find the peak-to-peak inductor ripple current ΔIL.

Vin​ = 48 VVo​ = 33.6 Vf = 20 kHzL = 220 µH
ΔIL = A
10.DC-DC convertersHard
tiL​Imax​Io​DTT2T

A buck converter turns 9 V into 3.6 V at 25 kHz with L = 33 µH. Find the smallest load current Io,min for which it stays in continuous conduction.

Vin​ = 9 VVo​ = 3.6 Vf = 25 kHzL = 33 µH
Io,min = A
11.Wheatstone bridge & strain gaugesMedium
+−2 V100 Ω100 Ω + ΔR100 Ω100 Ωab+−Vab​ = ?

A bridge has four 100 Ω arms and Vs = 2 V. The sensor R₂ increases by ΔR = 5 Ω. Find the exact output Vab in mV.

Vs = 2 VR = 100 ΩΔR = 5 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−5 V120 Ω − ΔR120 Ω + ΔR120 Ω + ΔR120 Ω − ΔRab+−Vo​ = ?

A bridge with 120 Ω arms is excited with 5 V and has four active gauges, two in tension and two in compression (full bridge). The gauge factor is 2 and the strain is 500 µε. Find the bridge output Vo in mV.

Vs = 5 VGF = 2ε = 500 µε
Vo = mV
13.Digital logic: gates, K-maps & flip-flopsMedium
MUX0I0​1I1​C′I2​1I3​ABS1​S0​F

A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = 0, I₁ = 1, I₂ = C′, I₃ = 1. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.

I₀ = 0I₁ = 1I₂ = C′I₃ = 1
N =
14.Digital logic: gates, K-maps & flip-flopsHard
ABCD0001111000011110X011X3121405070601201311511408X9011X10

For F(A, B, C, D) = Σm(1, 2, 4, 14, 15) + d(0, 3, 9, 10), where d marks the don't-care conditions, find the number N of essential prime implicants.

F(A, B, C, D) = Σm(1, 2, 4, 14, 15) + d(0, 3, 9, 10)
N =

3Solutions

1.Diodes & transistors

Answer: R = 1800 Ω

LED and diode circuits: a forward-biased LED drops roughly its forward voltage VF (about 2 V for red, 3 V for blue or white), whatever the current. A series resistor sets the current: R = (Vs − n·VF)/I for n LEDs in series. With a more exact diode model V = V₀ + I·rd, the operating point is where the diode line meets the load line I = (Vs − V)/R, so I = (Vs − V₀)/(R + rd).

Voltage across the resistor

VR = 24 − 2·3 = 18 V

Resistance

R = 18/0.01 = 1800 Ω

Answer

R = 1800 Ω

The resistor dissipates 180 mW.

2.Diodes & transistors

Answer: Rmax = 876.2 Ω

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case current

IR = 20 + 1 = 21 mA

Largest resistance

Rmax = 18.4/0.021 = 876.2 Ω

Answer

Rmax = 876.2 Ω
3.Op-amp circuits

Answer: Rf = 240 kΩ

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain of a non-inverting amplifier

V₋ = V₊ = Vin, and the current through R₁ also flows through Rf, so Vout = Vin·(1 + Rf/R₁).

Av = 1 + Rf/R1
Rf = (25 − 1)·10 = 240 kΩ

Answer

Rf = 240 kΩ
4.Op-amp circuits

Answer: Vout = 0.4278 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain of each stage

A1 = −Rf1/R1 = −4.7/2 = −2.35
A2 = 1 + Rf2/R2 = 1 + 4.7/22 = 1.214

Stage by stage

V1 = −2.35·(−0.15) = 0.3525 V
Vout = 1.214·0.3525 = 0.4278 V

Answer

Vout = 0.4278 V
5.RC & RL transients

Answer: vL = 9.587 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 68 mH / 50 Ω = 1.36 ms
i(∞) = Vs/R = 20/50 = 0.4 A

Inductor voltage

At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.

vL(t) = Vs·e−t/τ = 20·e−1/1.36 = 9.587 V

Answer

vL = 9.587 V
6.RC & RL transients

Answer: t = 0.1409 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

Before t = 0 the closed switch bypasses R₂; afterwards R₁ and R₂ are both in the loop.

i(0) = 6/33 = 0.1818 A
i(∞) = 6/(33 + 47) = 0.075 A
τ = L/R = 22/80 = 0.275 ms
i(t) = 0.075 + (0.1818 − 0.075)·e−t/τ

Solve for the time

e−t/τ = (0.139 − 0.075)/(0.1818 − 0.075) = 0.5991
t = 0.275·ln(1.669) = 0.1409 ms

Answer

t = 0.1409 ms
7.Series & parallel resistors

Answer: Req = 19.29 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 15 ΩR3​ = 5 Ω+−V1​9 VR2​6 ΩAR4​10 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 5 + 10 = 15 Ω
R2 ∥ 15 = 6·15/(6+15) = 4.286 Ω
Req = R1 + 4.286 = 15 + 4.286 = 19.29 Ω

Answer

Req = 19.29 Ω
8.Series & parallel resistors

Answer: IR2 = 0.4165 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 30 ΩR3​ = 15 ΩR5​ = 12 Ω+−V1​30 VR2​20 ΩAR4​25 ΩBR6​12 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 12 + 12 = 24 Ω
R4 ∥ 24 = 12.24 Ω
R3 + 12.24 = 27.24 Ω
R2 ∥ 27.24 = 11.53 Ω
Req = R1 + 11.53 = 30 + 11.53 = 41.53 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 30/41.53 = 0.7223 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

VA = V1 − IR1·R1 = 30 − 0.7223·30 = 8.331 V
IR2 = VA/R2 = 8.331/20 = 0.4165 A

Answer

IR2 = 0.4165 A
9.DC-DC converters

Answer: ΔIL = 2.291 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 33.6/48 = 0.7

Inductor voltage during the on-time

While S is on, the inductor sits between Vin and Vo.

VL = 48 − 33.6 = 14.4 V

Ripple current

ΔIL = VL·D/(L·f) = 14.4·0.7/(220·10⁻⁶·20·10³) = 2.291 A

Answer

ΔIL = 2.291 A
10.DC-DC converters

Answer: Io,min = 1.309 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 3.6/9 = 0.4

Ripple current

ΔIL = 3.6·0.6/(33·10⁻⁶·25·10³) = 2.618 A

Boundary load current

Io,min = ΔIL/2 = 1.309 A

Answer

Io,min = 1.309 A

Below this current the converter enters discontinuous conduction and Vo rises above D·Vin.

11.Wheatstone bridge & strain gauges

Answer: Vab = 24.39 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Node voltages

Va = 2·105/205 = 1.024 V
Vb = 1 V

Output

Vab = 24.39 mV

Answer

Vab = 24.39 mV

The linear estimate Vs·ΔR/(4R) = 25 mV is 2.5 % too high: a quarter bridge is not quite linear.

12.Wheatstone bridge & strain gauges

Answer: Vo = 5 mV

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Relative resistance change

ΔR/R = 2·500·10⁻⁶ = 0.001

Bridge output

Vo = Vs·GF·ε = 5·0.001 = 5 mV

Answer

Vo = 5 mV
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 5

Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.

Output expression

F = A′B + AB′C′ + AB

Rows with F = 1

ABC = 010, 011, 100, 110, 111
N = 5

Answer

N = 5
14.Digital logic: gates, K-maps & flip-flops

Answer: N = 2

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Prime implicants

The largest groups that can be formed from 1s and Xs.

B′C′D, B′CD′, A′C′D′, ACD′, A′B′, ABC
ABCD0001111000011110X011X3121405070601201311511408X9011X10

Essential prime implicants

A′C′D′, ABC
N = 2

Answer

N = 2

ExamProblems · examproblems.com/courses/electronics-1