Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Digital logic: gates, K-maps & flip-flops
Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states
Method
For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.
2Practice problems
1.Diodes & transistorsMedium
An NPN transistor with β = 100 has voltage-divider bias from VCC = 18 V: R₁ = 56 kΩ from VCC to the base and R₂ = 10 kΩ from the base to ground. The collector resistor is RC = 2.7 kΩ and the emitter resistor is RE = 1 kΩ. Take VBE = 0.7 V and use the Thévenin equivalent of the divider (do not neglect the base current). Find the collector–emitter voltage VCE.
An NPN transistor with β = 200 switches a 680 Ω load resistor connected between VCC = 24 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB = 100 kΩ. Take VBE = 0.7 V and VCE(sat) = 0.2 V. Find the collector current IC in mA when the input is high. Decide first whether the transistor is saturated.
The inductor carries a steady current of 3 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. How long does it take for the current to fall to 1.5 A? Find t.
i(0) = 3 AR = 20 ΩL = 68 mH
t = ms
6.RC & RL transientsHard
A timer starts charging an uncharged capacitor through a resistor from a 12 V supply at t = 0. It must trigger when the capacitor voltage reaches 6 V, exactly 1000 ms after the start. With R = 10 kΩ, find the capacitance C needed.
Vs = 12 VVth = 6 VT = 1000 msR = 10 kΩ
C = µF
7.Series & parallel resistorsMedium
Find the current IR1 delivered by the source, which flows through R1.
V1 = 24 VR1 = 2 ΩR2 = 3 ΩR3 = 3 ΩR4 = 20 Ω
IR1 = A
8.Series & parallel resistorsHard
Find the equivalent resistance Req seen by the source V1.
An ideal boost converter turns 48 V into 96 V at 100 kHz with L = 68 µH. Find the peak-to-peak inductor ripple current ΔIL.
Vin = 48 VVo = 96 Vf = 100 kHzL = 68 µH
ΔIL = A
10.DC-DC convertersHard
An ideal boost converter turns 15 V into 60 V for a 12 Ω load at 200 kHz. Find the smallest inductance Lcrit for continuous conduction.
Vin = 15 VVo = 60 Vf = 200 kHzR = 12 Ω
Lcrit = µH
11.Wheatstone bridge & strain gaugesMedium
A bridge with four 220 Ω arms is supplied with 15 V. When the sensor R₂ changes, the output reads Vab = 37.31 mV. Find the exact change ΔR of R₂.
Vs = 15 VR = 220 ΩVab = 37.31 mV
ΔR = Ω
12.Wheatstone bridge & strain gaugesHard
A quarter bridge (one active gauge, GF = 2.12) is excited with 5 V. The largest strain to be measured is 800 µε, and it must give 10 V at the input of an analogue-to-digital converter. Find the amplifier gain G.
In this Karnaugh map exactly one 1 has no neighbouring 1, so it stays a group of one cell (a full minterm of four literals) in the minimal SOP form. Neighbours across the map edges count. Click that cell.
F = Σm(0, 4, 7, 12, 13, 14)
1AB = 00, CD = 00
2AB = 00, CD = 01
3AB = 00, CD = 11
4AB = 00, CD = 10
5AB = 01, CD = 00
6AB = 01, CD = 01
7AB = 01, CD = 11
8AB = 01, CD = 10
9AB = 11, CD = 00
10AB = 11, CD = 01
11AB = 11, CD = 11
12AB = 11, CD = 10
13AB = 10, CD = 00
14AB = 10, CD = 01
15AB = 10, CD = 11
16AB = 10, CD = 10
14.Digital logic: gates, K-maps & flip-flopsHard
A mod-25 counter is built from the minimum number of flip-flops. How many of the possible states U are never used?
N = 25
U =
3Solutions
1.Diodes & transistors
Answer: VCE = 11.13 V
BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.
Thévenin equivalent of the divider
VTH = 18·10/(56 + 10) = 2.727 V
RTH = 56·10/(56 + 10) = 8.485 kΩ
Base current
KVL around the base loop; the emitter current is (β + 1)·IB.
IB = (2.727 − 0.7)/(8.485 + 101·1) = 18.52 µA
Collector current
IC = 100·18.52 µA = 1.852 mA
IE = 101·18.52 µA = 1.87 mA
Collector–emitter voltage
VCE = 18 − 1.852·2.7 − 1.87·1 = 11.13 V
Answer
VCE = 11.13 V
2.Diodes & transistors
Answer: IC = 5.2 mA
BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.
Base current
IB = (3.3 − 0.7)/100 kΩ = 26 µA
Saturated or active?
β·IB is smaller than IC(sat), so the transistor stays active.
β·IB = 5.2 mA
IC(sat) = (24 − 0.2)/680 = 35 mA
Collector current
IC = β·IB = 5.2 mA
Answer
IC = 5.2 mA
The transistor is active, so the load is not fully switched on.
3.Op-amp circuits
Answer: Vout = −2.341 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Voltage at the + input
V₊ = V2·R4/(R3 + R4) = 1.5·1/(22 + 1) = 0.06522 V
Superpose the two inputs
With V₂ = 0, V₁ sees an inverting amplifier. With V₁ = 0, V₊ is amplified by the non-inverting gain 1 + R₂/R₁.
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant
τ = L/R = 68 mH / 20 Ω = 3.4 ms
Solve for the time
1.5 = 3·e−t/τ → t = τ·ln(3/1.5)
t = 3.4·ln(2) = 2.357 ms
Answer
t = 2.357 ms
6.RC & RL transients
Answer: C = 144.3 µF
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Required time constant
6 = 12·(1 − e−1000/τ) → τ = 1000/ln(12/(12 − 6))
τ = 1000/0.6931 = 1443 ms
Capacitance
kΩ times µF gives milliseconds.
C = τ/R = 1443/10 = 144.3 µF
Answer
C = 144.3 µF
7.Series & parallel resistors
Answer: IR1 = 5.157 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 3 + 20 = 23 Ω
R2 ∥ 23 = 3·23/(3+23) = 2.654 Ω
Req = R1 + 2.654 = 2 + 2.654 = 4.654 Ω
Current from the source
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
IR1 = V1/Req = 24/4.654 = 5.157 A
Answer
IR1 = 5.157 A
8.Series & parallel resistors
Answer: Req = 29.91 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 3 + 25 = 28 Ω
R4 ∥ 28 = 2.71 Ω
R3 + 2.71 = 12.71 Ω
R2 ∥ 12.71 = 4.91 Ω
Req = R1 + 4.91 = 25 + 4.91 = 29.91 Ω
Answer
Req = 29.91 Ω
9.DC-DC converters
Answer: ΔIL = 3.529 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 1 − 48/96 = 0.5
Inductor voltage during the on-time
While S is on, the inductor sits directly across Vin.
VL = 48 V
Ripple current
ΔIL = VL·D/(L·f) = 48·0.5/(68·10⁻⁶·100·10³) = 3.529 A
Answer
ΔIL = 3.529 A
10.DC-DC converters
Answer: Lcrit = 1.406 µH
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 1 − 15/60 = 0.75
Boundary condition
Set the average inductor current equal to half the ripple current and solve for L.
Lcrit = D(1 − D)²·R/(2f)
Critical inductance
Lcrit = 0.75(1 − 0.75)²·12/(2200·10³) = 1.406 µH
Answer
Lcrit = 1.406 µH
11.Wheatstone bridge & strain gauges
Answer: ΔR = 2.2 Ω
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Node voltage
Va = 7.5 + 0.03731 = 7.537 V
Solve the divider
R₂ = 220·7.537/(15 − 7.537) = 222.2 Ω
ΔR = 222.2 − 220 = 2.2 Ω
Answer
ΔR = 2.2 Ω
12.Wheatstone bridge & strain gauges
Answer: G = 4717
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Bridge output at full scale
Vo = 2.12 mV
Gain
G = 10/0.00212 = 4717
Answer
G = 4717
13.Digital logic: gates, K-maps & flip-flops
Answer: AB = 01, CD = 11
Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.
Neighbours of each 1
A 1 with a neighbouring 1 can join a group of two or more.
m7: m6, m5, m3, m15 → 0
The isolated 1
m7 = A′BCD → AB = 01, CD = 11
Answer
AB = 01, CD = 11
14.Digital logic: gates, K-maps & flip-flops
Answer: U = 7
Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.