Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Digital logic: gates, K-maps & flip-flops
Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states
Method
For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.
2Practice problems
1.Diodes & transistorsMedium
An NPN transistor with β = 80 has voltage-divider bias from VCC = 15 V: R₁ = 68 kΩ from VCC to the base and R₂ = 8.2 kΩ from the base to ground. The collector resistor is RC = 2.7 kΩ and the emitter resistor is RE = 1.2 kΩ. Take VBE = 0.7 V and use the Thévenin equivalent of the divider (do not neglect the base current). Find the collector current IC in mA.
A 3.3 V Zener regulator has a 680 Ω series resistor. The input can rise to 12 V, and the load may be disconnected. Find the largest power PZ,max the Zener must dissipate.
Vin,max = 12 VVZ = 3.3 VR = 680 Ω
PZ,max = mW
3.Op-amp circuitsMedium
The op-amp is ideal and runs from ±15 V supplies. Find the output voltage Vout.
An ideal buck converter turns 15 V into 9 V at 500 kHz with L = 68 µH. Find the peak-to-peak inductor ripple current ΔIL.
Vin = 15 VVo = 9 Vf = 500 kHzL = 68 µH
ΔIL = A
10.DC-DC convertersHard
An ideal boost converter turns 48 V into 120 V for a 4 Ω load at 250 kHz. The output capacitor is 10 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.
Vin = 48 VVo = 120 Vf = 250 kHzC = 10 µFR = 4 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
Find the Thévenin resistance Rth of the bridge shown, seen from the output terminals a and b.
In this Karnaugh map exactly one 1 has no neighbouring 1, so it stays a group of one cell (a full minterm of four literals) in the minimal SOP form. Neighbours across the map edges count. Click that cell.
F = Σm(4, 6, 9, 12)
1AB = 00, CD = 00
2AB = 00, CD = 01
3AB = 00, CD = 11
4AB = 00, CD = 10
5AB = 01, CD = 00
6AB = 01, CD = 01
7AB = 01, CD = 11
8AB = 01, CD = 10
9AB = 11, CD = 00
10AB = 11, CD = 01
11AB = 11, CD = 11
12AB = 11, CD = 10
13AB = 10, CD = 00
14AB = 10, CD = 01
15AB = 10, CD = 11
16AB = 10, CD = 10
14.Digital logic: gates, K-maps & flip-flopsHard
A 4-bit ring counter Q₃Q₂Q₁Q₀ starts at 1010. At every clock edge the bits shift one place to the right (Q₃ → Q₂ → Q₁ → Q₀) and Q₃ receives Q₀. Give the state Q = Q₃Q₂Q₁Q₀ as a decimal number after 8 clock edges.
Q₃Q₂Q₁Q₀ = 10108
Q =
3Solutions
1.Diodes & transistors
Answer: IC = 0.6997 mA
BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.
Thévenin equivalent of the divider
VTH = 15·8.2/(68 + 8.2) = 1.614 V
RTH = 68·8.2/(68 + 8.2) = 7.318 kΩ
Base current
KVL around the base loop; the emitter current is (β + 1)·IB.
IB = (1.614 − 0.7)/(7.318 + 81·1.2) = 8.747 µA
Collector current
IC = 80·8.747 µA = 0.6997 mA
IE = 81·8.747 µA = 0.7085 mA
Answer
IC = 0.6997 mA
2.Diodes & transistors
Answer: PZ,max = 42.22 mW
Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.
Worst-case Zener current
IZ = 8.7/680 = 12.79 mA
Zener power
PZ = 3.3·12.79 = 42.22 mW
Answer
PZ,max = 42.22 mW
3.Op-amp circuits
Answer: Vout = 2.5 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Voltage at the + input
V₊ = Vin·Rb/(Ra + Rb) = 2.5·47/(47 + 47) = 1.25 V
Non-inverting gain
V₋ = V₊, and the current through R₁ also flows through Rf.
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Input currents
V₋ = 0, so each input resistor has its full input voltage across it.
I1 = V1/R1 = −1.9/100 = −0.019 mA
I2 = V2/R2 = 1.8/2 = 0.9 mA
If = I1 + I2 = 0.881 mA
Output voltage
Vout = −Rf·If = −10·0.881 = −8.81 V
Answer
Vout = −8.81 V
5.RC & RL transients
Answer: vL = 1.488 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant and final current
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
τ = L/R = 33 mH / 20 Ω = 1.65 ms
i(∞) = Vs/R = 5/20 = 0.25 A
Inductor voltage
At t = 0 the whole supply voltage appears across the inductor; it then decays to zero.
vL(t) = Vs·e−t/τ = 5·e−2/1.65 = 1.488 V
Answer
vL = 1.488 V
6.RC & RL transients
Answer: t = 116.8 ms
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Initial value, final value, time constant
The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.
t = τ·ln((2 − 12)/(10 − 12)) = 72.6·ln(5) = 116.8 ms
Answer
t = 116.8 ms
7.Series & parallel resistors
Answer: IR1 = 1.607 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 2 + 8 = 10 Ω
R2 ∥ 10 = 20·10/(20+10) = 6.667 Ω
Req = R1 + 6.667 = 12 + 6.667 = 18.67 Ω
Current from the source
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
IR1 = V1/Req = 30/18.67 = 1.607 A
Answer
IR1 = 1.607 A
8.Series & parallel resistors
Answer: Req = 12.11 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 8 + 25 = 33 Ω
R4 ∥ 33 = 12.45 Ω
R3 + 12.45 = 20.45 Ω
R2 ∥ 20.45 = 10.11 Ω
Req = R1 + 10.11 = 2 + 10.11 = 12.11 Ω
Answer
Req = 12.11 Ω
9.DC-DC converters
Answer: ΔIL = 0.1059 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 9/15 = 0.6
Inductor voltage during the on-time
While S is on, the inductor sits between Vin and Vo.
VL = 15 − 9 = 6 V
Ripple current
ΔIL = VL·D/(L·f) = 6·0.6/(68·10⁻⁶·500·10³) = 0.1059 A
Answer
ΔIL = 0.1059 A
10.DC-DC converters
Answer: ΔVo = 7200 mV
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 1 − 48/120 = 0.6
Load current
Io = 120/4 = 30 A
Output ripple
ΔVo = 30·0.6/(250·10³·10·10⁻⁶) = 7200 mV
Answer
ΔVo = 7200 mV
11.Wheatstone bridge & strain gauges
Answer: Rth = 330.4 Ω
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Supply shorted
R₁∥R₂ = 600·300/900 = 200 Ω
R₃∥R₄ = 150·1000/1150 = 130.4 Ω
Thévenin resistance
Rth = 330.4 Ω
Answer
Rth = 330.4 Ω
12.Wheatstone bridge & strain gauges
Answer: σ = 160 MPa
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Strain
ε = 4·0.004/(10·2) = 0.0008
Stress
σ = 200·10³ MPa·0.0008 = 160 MPa
Answer
σ = 160 MPa
13.Digital logic: gates, K-maps & flip-flops
Answer: AB = 10, CD = 01
Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.
Neighbours of each 1
A 1 with a neighbouring 1 can join a group of two or more.
m9: m8, m11, m13, m1 → 0
The isolated 1
m9 = AB′C′D → AB = 10, CD = 01
Answer
AB = 10, CD = 01
14.Digital logic: gates, K-maps & flip-flops
Answer: Q = 10
Flip-flops and counters: a flip-flop changes only at the active clock edge. D copies its input (Q⁺ = D); T toggles when T = 1; JK holds for 00, resets for 01, sets for 10 and toggles for 11. An n-bit binary counter has 2ⁿ states and counts modulo 2ⁿ; a mod-N counter goes 0, 1, …, N − 1 and back to 0, and needs the smallest n with 2ⁿ ≥ N flip-flops. Each stage of a ripple counter halves the frequency, so the last output of a mod-N counter runs at fclk/N. A Johnson counter of n flip-flops has 2n states, a ring counter n.