Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
RC​ = 3.3 kΩβ = 75IC​ = ?VCC​ = 10 VRB​ = 820 kΩ

An NPN transistor with β = 75 is biased by a base resistor RB = 820 kΩ from the supply VCC = 10 V. The collector resistor is RC = 3.3 kΩ and the emitter is grounded. Take VBE = 0.7 V and assume the transistor is in the active region. Find the collector current IC in mA.

VCC = 10 VRB = 820 kΩRC = 3.3 kΩβ = 75VBE = 0.7 V
IC = mA
2.Diodes & transistorsHard
RC​ = 150 Ωβ = 100VCC​ = 24 V5 VRB​ = ?

An NPN transistor with β = 100 switches a 150 Ω load resistor connected between VCC = 24 V and its collector. The emitter is grounded. The base is driven from a 5 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. Find the largest base resistor RB, in kΩ, that still drives the transistor just into saturation.

VCC = 24 VRC = 150 Ωβ = 100Vin = 5 VVBE = 0.7 VVCE(sat) = 0.2 V
RB = kΩ
3.Op-amp circuitsMedium
−+Vout​Rf​ = 47 kΩR1​ = 10 kΩVin​ = 1 VRa​ = 2 kΩRb​ = 100 kΩ

The op-amp is ideal and runs from ±15 V supplies. Find the output voltage Vout.

Vin = 1 VRa = 2 kΩRb = 100 kΩR1 = 10 kΩRf = 47 kΩ
Vout = V
4.Op-amp circuitsHard
−+Vout​Rf​ = 22 kΩV1​ = 1.6 VR1​ = 100 kΩV2​ = 0.1 VR2​ = 47 kΩIf​

The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the current If through the feedback resistor, flowing towards the output.

V1 = 1.6 VV2 = 0.1 VR1 = 100 kΩR2 = 47 kΩRf = 22 kΩ
If = mA
5.RC & RL transientsMedium
+−Vs​9 Vt = 0R1​ = 1 kΩR2​ = 2.2 kΩC22 µF+−vC​

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the time constant τ of the circuit after the switch closes.

Vs = 9 VR1 = 1 kΩR2 = 2.2 kΩC = 22 µF
τ = ms
6.RC & RL transientsHard
+−Vs​9 Vt = 0R = 3.3 kΩC220 µF+−vC​vC​(0) = 20 V

Just before the switch closes at t = 0, the capacitor holds 20 V with the polarity shown. Find the capacitor voltage vC at t = 750 ms.

Vs = 9 VR = 3.3 kΩC = 220 µFvC(0) = 20 Vt = 750 ms
vC = V
7.Series & parallel resistorsMedium
R1​ = 20 ΩR3​ = 3 Ω+−V1​12 VR2​2 ΩIR2​AR4​3 ΩB

Find the current IR2 through R2.

V1 = 12 VR1 = 20 ΩR2 = 2 ΩR3 = 3 ΩR4 = 3 Ω
IR2 = A
8.Series & parallel resistorsHard
R1​ = 2 ΩIR1​R3​ = 6 ΩR5​ = 5 Ω+−V1​15 VR2​8 ΩAR4​20 ΩBR6​2 Ω

Find the current IR1 delivered by the source, which flows through R1.

V1 = 15 VR1 = 2 ΩR2 = 8 ΩR3 = 6 ΩR4 = 20 ΩR5 = 5 ΩR6 = 2 Ω
IR1 = A
9.DC-DC convertersMedium
tiL​Imax​Imin​ΔI = ?DTT2T

An ideal inverting buck-boost converter turns 9 V into −21 V at 40 kHz with L = 47 µH. Find the peak-to-peak inductor ripple current ΔIL.

Vin​ = 9 VVo​ = −21 Vf = 40 kHzL = 47 µH
ΔIL = A
10.DC-DC convertersHard
tiL​Imax​IL​DTT2T

An ideal inverting buck-boost converter turns 36 V into −108 V for a 12 Ω load at 50 kHz. Find the smallest inductance Lcrit for continuous conduction.

Vin​ = 36 VVo​ = −108 Vf = 50 kHzR = 12 Ω
Lcrit = µH
11.Wheatstone bridge & strain gaugesMedium
+−3 VR1​ = 800 ΩR2​ = 200 ΩR3​ = 10 ΩR4​ = 1000 ΩabGRg​ = 500 Ω

A galvanometer with a resistance of 500 Ω is connected between a and b of the bridge shown (Vs = 3 V). Find the galvanometer current Ig from a to b, in µA.

Vs = 3 VR1 = 800 ΩR2 = 200 ΩR3 = 10 ΩR4 = 1000 ΩRg = 500 Ω
Ig = µA
12.Wheatstone bridge & strain gaugesHard
+−5 V350 Ω350 Ω + ΔR350 Ω350 Ωab+−Vo​

A quarter bridge (one active gauge, GF = 2) is excited with 5 V. The largest strain to be measured is 800 µε, and it must give 5 V at the input of an analogue-to-digital converter. Find the amplifier gain G.

Vs = 5 VGF = 2εmax = 800 µεVFS = 5 V
G =
13.Digital logic: gates, K-maps & flip-flopsMedium
ABCD000111100001111000110312041517060120130151140819011110

Use the Karnaugh map to find the minimal product-of-sums (POS) form of F(A, B, C, D) = Σm(1, 2, 5, 7, 9, 10, 14). How many sum terms (factors) N does it have?

F(A, B, C, D) = Σm(1, 2, 5, 7, 9, 10, 14)
N =
14.Digital logic: gates, K-maps & flip-flopsHard
ABCD00011110000111101011031214051716X12113115014X819011110

Find the minimal SOP form of F(A, B, C, D) = Σm(0, 1, 2, 4, 6, 7, 9, 10, 13, 15) + d(8, 12), where d marks the don't-care conditions. How many product terms N does it have?

F(A, B, C, D) = Σm(0, 1, 2, 4, 6, 7, 9, 10, 13, 15) + d(8, 12)
N =

3Solutions

1.Diodes & transistors

Answer: IC = 0.8506 mA

BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.

Base current

IB = (VCC − VBE)/RB = (10 − 0.7)/820 kΩ = 11.34 µA

Collector current

IC = β·IB = 75·11.34 µA = 0.8506 mA

Answer

IC = 0.8506 mA

Check: VCE = 7.193 V is well above 0.2 V, so the transistor is indeed active.

2.Diodes & transistors

Answer: RB = 2.71 kΩ

BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.

Collector current in saturation

IC(sat) = (24 − 0.2)/150 = 158.7 mA

Minimum base current

IB(min) = IC(sat)/β = 158.7/100 = 1587 µA

Base resistor

RB = (5 − 0.7)/IB = 4.3 V/1.587 mA = 2.71 kΩ

Answer

RB = 2.71 kΩ

Any smaller base resistor also saturates the transistor; in practice you pick one a few times smaller.

3.Op-amp circuits

Answer: Vout = 5.588 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Voltage at the + input

V₊ = Vin·Rb/(Ra + Rb) = 1·100/(2 + 100) = 0.9804 V

Non-inverting gain

V₋ = V₊, and the current through R₁ also flows through Rf.

Vout = V₊·(1 + Rf/R1) = 0.9804·(1 + 47/10) = 5.588 V

Answer

Vout = 5.588 V
4.Op-amp circuits

Answer: If = 0.01813 mA

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input currents

V₋ = 0, so each input resistor has its full input voltage across it.

I1 = V1/R1 = 1.6/100 = 0.016 mA
I2 = V2/R2 = 0.1/47 = 0.002128 mA
If = I1 + I2 = 0.01813 mA

Answer

If = 0.01813 mA
5.RC & RL transients

Answer: τ = 15.13 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find Rth; open the capacitor to find the voltage it will settle at.

Rth = R1 ∥ R2 = 1·2.2/(1 + 2.2) = 0.6875 kΩ
vC(∞) = 9·2.2/(1 + 2.2) = 6.188 V

Time constant

τ = Rth·C = 0.6875·22 = 15.13 ms

Answer

τ = 15.13 ms
6.RC & RL transients

Answer: vC = 12.92 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 20 V, vC(∞) = Vs = 9 V
τ = R·C = 3.3 kΩ · 220 µF = 726 ms
vC(t) = 9 + (20 − 9)·e−t/τ

Voltage at the given time

vC(750) = 9 + (11)·e−750/726 = 12.92 V

Answer

vC = 12.92 V
7.Series & parallel resistors

Answer: IR2 = 0.4186 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 20 ΩR3​ = 3 Ω+−V1​12 VR2​2 ΩAR4​3 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 3 + 3 = 6 Ω
R2 ∥ 6 = 2·6/(2+6) = 1.5 Ω
Req = R1 + 1.5 = 20 + 1.5 = 21.5 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 12/21.5 = 0.5581 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

VA = V1 − IR1·R1 = 12 − 0.5581·20 = 0.8372 V
IR2 = VA/R2 = 0.8372/2 = 0.4186 A

Answer

IR2 = 0.4186 A
8.Series & parallel resistors

Answer: IR1 = 2.251 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 2 ΩR3​ = 6 ΩR5​ = 5 Ω+−V1​15 VR2​8 ΩAR4​20 ΩBR6​2 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 5 + 2 = 7 Ω
R4 ∥ 7 = 5.185 Ω
R3 + 5.185 = 11.19 Ω
R2 ∥ 11.19 = 4.664 Ω
Req = R1 + 4.664 = 2 + 4.664 = 6.664 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 15/6.664 = 2.251 A

Answer

IR1 = 2.251 A
9.DC-DC converters

Answer: ΔIL = 3.351 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 21/(9 + 21) = 0.7

Inductor voltage during the on-time

While S is on, the inductor sits directly across Vin.

VL = 9 V

Ripple current

ΔIL = VL·D/(L·f) = 9·0.7/(47·10⁻⁶·40·10³) = 3.351 A

Answer

ΔIL = 3.351 A
10.DC-DC converters

Answer: Lcrit = 7.5 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 108/(36 + 108) = 0.75

Boundary condition

Set the average inductor current equal to half the ripple current and solve for L.

Lcrit = (1 − D)²·R/(2f)

Critical inductance

Lcrit = (1 − 0.75)²·12/(250·10³) = 7.5 µH

Answer

Lcrit = 7.5 µH
11.Wheatstone bridge & strain gauges

Answer: Ig = −3538 µA

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Thévenin voltage

Vth = 3·(200/1000 − 1000/1010) = −2.37 V

Thévenin resistance

Rth = R₁∥R₂ + R₃∥R₄ = 169.9 Ω

Galvanometer current

Ig = −2.37/(169.9 + 500) = −3538 µA

Answer

Ig = −3538 µA
12.Wheatstone bridge & strain gauges

Answer: G = 2500

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Bridge output at full scale

Vo = 2 mV

Gain

G = 5/0.002 = 2500

Answer

G = 2500
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 4

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

ABCD000111100001111000110312041517060120130151140819011110

Group the 0s

Every group is a rectangle of 2ᵏ cells; edge cells are neighbours of the cells on the opposite edge.

(C + D)
(B + C′ + D′)
(A + B′ + D)
(A′ + B′ + D′)

Minimal POS form

F = (C + D)(B + C′ + D′)(A + B′ + D)(A′ + B′ + D′)
N = 4

Answer

N = 4
14.Digital logic: gates, K-maps & flip-flops

Answer: N = 5

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Prime implicants

The largest groups that can be formed from 1s and Xs.

C′D′, B′D′, B′C′, BCD, A′D′, AC′, ABD, A′BC
ABCD00011110000111101011031214051716X12113115014X819011110

Minimal cover

F = B′D′ + B′C′ + BCD + A′D′ + AC′
N = 5

Answer

N = 5

ExamProblems · examproblems.com/courses/electronics-1