Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
RC​ = 1 kΩβ = 120IC​ = ?VCC​ = 10 VRB​ = 470 kΩ

An NPN transistor with β = 120 is biased by a base resistor RB = 470 kΩ from the supply VCC = 10 V. The collector resistor is RC = 1 kΩ and the emitter is grounded. Take VBE = 0.7 V and assume the transistor is in the active region. Find the collector current IC in mA.

VCC = 10 VRB = 470 kΩRC = 1 kΩβ = 120VBE = 0.7 V
IC = mA
2.Diodes & transistorsHard
+−≤ 17 V470 Ω5.1 V

A 5.1 V Zener regulator has a 470 Ω series resistor. The input can rise to 17 V, and the load may be disconnected. Find the largest power PZ,max the Zener must dissipate.

Vin,max = 17 VVZ = 5.1 VR = 470 Ω
PZ,max = mW
3.Op-amp circuitsMedium
−+Vout​Rf​ = ?R1​ = 22 kΩVin​

Choose the feedback resistor Rf that gives this non-inverting amplifier a voltage gain of 8.

R1 = 22 kΩAv = 8
Rf = kΩ
4.Op-amp circuitsHard
−+Vout​R2​ = 10 kΩV1​ = −2 VR1​ = 22 kΩV2​ = 0.5 VR3​ = 100 kΩR4​ = 1 kΩ

The op-amp is ideal and runs from ±15 V supplies. The resistor ratios are not matched. Find the output voltage Vout.

V1 = −2 VV2 = 0.5 VR1 = 22 kΩR2 = 10 kΩR3 = 100 kΩR4 = 1 kΩ
Vout = V
5.RC & RL transientsMedium
+−Vs​5 Vt = 0R = 100 ΩL100 mHi(t)

The inductor carries no current before the switch closes at t = 0. Find the current i at t = 1 ms.

Vs = 5 VR = 100 ΩL = 100 mHt = 1 ms
i = A
6.RC & RL transientsHard
+−Vs​5 Vt = 0R = ?C2.2 µF+−vC​

A timer starts charging an uncharged capacitor through a resistor from a 5 V supply at t = 0. It must trigger when the capacitor voltage reaches 4.5 V, exactly 100 ms after the start. With C = 2.2 µF, find the resistance R needed.

Vs = 5 VVth = 4.5 VT = 100 msC = 2.2 µF
R = kΩ
7.Series & parallel resistorsMedium
R1​ = 5 ΩR3​ = 6 Ω+−V1​30 VR2​4 ΩIR2​AR4​10 ΩB

Find the current IR2 through R2.

V1 = 30 VR1 = 5 ΩR2 = 4 ΩR3 = 6 ΩR4 = 10 Ω
IR2 = A
8.Series & parallel resistorsHard
R1​ = 4 ΩR3​ = 20 ΩR5​ = 25 Ω+−V1​36 VR2​6 ΩAR4​30 ΩBR6​15 Ω

Find the equivalent resistance Req seen by the source V1.

V1 = 36 VR1 = 4 ΩR2 = 6 ΩR3 = 20 ΩR4 = 30 ΩR5 = 25 ΩR6 = 15 Ω
Req = Ω
9.DC-DC convertersMedium
+−48 VSL = ?CR+−36 V

An ideal buck converter turns 48 V into 36 V at a switching frequency of 20 kHz. Find the inductance L that keeps the peak-to-peak inductor ripple current at 1.5 A.

Vin​ = 48 VVo​ = 36 Vf = 20 kHzΔIL = 1.5 A
L = µH
10.DC-DC convertersHard
tiL​Imax​IL​DTT2T

An ideal boost converter turns 12 V into 16 V for a 20 Ω load at 250 kHz. Find the smallest inductance Lcrit for continuous conduction.

Vin​ = 12 VVo​ = 16 Vf = 250 kHzR = 20 Ω
Lcrit = µH
11.Wheatstone bridge & strain gaugesMedium
+−10 V330 Ω330 Ω330 Ω330 Ωab+−

A 330 Ω strain gauge is one arm (R₂) of a bridge with four equal 330 Ω arms and an excitation of 10 V. Find the power Pg dissipated in the gauge, in mW. Self-heating limits the excitation.

Vs = 10 VR = 330 Ω
Pg = mW
12.Wheatstone bridge & strain gaugesHard
+−3 V350 Ω − ΔR350 Ω + ΔR350 Ω350 Ωab+−Vo​ = ?

A bridge with 350 Ω arms is excited with 3 V and has two active gauges in adjacent arms, one in tension and one in compression (half bridge). The gauge factor is 2.05 and the strain is 800 µε. Find the bridge output Vo in mV.

Vs = 3 VGF = 2.05ε = 800 µε
Vo = mV
13.Digital logic: gates, K-maps & flip-flopsMedium
ABCD0001111000011110111111111

In this Karnaugh map exactly one 1 has no neighbouring 1, so it stays a group of one cell (a full minterm of four literals) in the minimal SOP form. Neighbours across the map edges count. Click that cell.

F = Σm(0, 1, 2, 4, 8, 9, 10, 12, 15)
  1. 1AB = 00, CD = 00
  2. 2AB = 00, CD = 01
  3. 3AB = 00, CD = 11
  4. 4AB = 00, CD = 10
  5. 5AB = 01, CD = 00
  6. 6AB = 01, CD = 01
  7. 7AB = 01, CD = 11
  8. 8AB = 01, CD = 10
  9. 9AB = 11, CD = 00
  10. 10AB = 11, CD = 01
  11. 11AB = 11, CD = 11
  12. 12AB = 11, CD = 10
  13. 13AB = 10, CD = 00
  14. 14AB = 10, CD = 01
  15. 15AB = 10, CD = 11
  16. 16AB = 10, CD = 10
14.Digital logic: gates, K-maps & flip-flopsHard
ABCD000111100001111010110312X415X716X121130150141809111010

Find the minimal SOP form of F(A, B, C, D) = Σm(0, 1, 2, 5, 6, 8, 11, 13) + d(4, 7, 12), where d marks the don't-care conditions. How many product terms N does it have?

F(A, B, C, D) = Σm(0, 1, 2, 5, 6, 8, 11, 13) + d(4, 7, 12)
N =

3Solutions

1.Diodes & transistors

Answer: IC = 2.374 mA

BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.

Base current

IB = (VCC − VBE)/RB = (10 − 0.7)/470 kΩ = 19.79 µA

Collector current

IC = β·IB = 120·19.79 µA = 2.374 mA

Answer

IC = 2.374 mA

Check: VCE = 7.626 V is well above 0.2 V, so the transistor is indeed active.

2.Diodes & transistors

Answer: PZ,max = 129.1 mW

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case Zener current

IZ = 11.9/470 = 25.32 mA

Zener power

PZ = 5.1·25.32 = 129.1 mW

Answer

PZ,max = 129.1 mW
3.Op-amp circuits

Answer: Rf = 154 kΩ

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain of a non-inverting amplifier

V₋ = V₊ = Vin, and the current through R₁ also flows through Rf, so Vout = Vin·(1 + Rf/R₁).

Av = 1 + Rf/R1
Rf = (8 − 1)·22 = 154 kΩ

Answer

Rf = 154 kΩ
4.Op-amp circuits

Answer: Vout = 0.9163 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Voltage at the + input

V₊ = V2·R4/(R3 + R4) = 0.5·1/(100 + 1) = 0.00495 V

Superpose the two inputs

With V₂ = 0, V₁ sees an inverting amplifier. With V₁ = 0, V₊ is amplified by the non-inverting gain 1 + R₂/R₁.

Vout = −(10/22)·(−2) + (1 + 10/22)·0.00495 = 0.9091 + 0.007201 = 0.9163 V

Answer

Vout = 0.9163 V
5.RC & RL transients

Answer: i = 0.03161 A

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant and final current

Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.

τ = L/R = 100 mH / 100 Ω = 1 ms
i(∞) = Vs/R = 5/100 = 0.05 A

Current at the given time

i(t) = i(∞)·(1 − e−t/τ) = 0.05·(1 − e−1/1) = 0.03161 A

Answer

i = 0.03161 A
6.RC & RL transients

Answer: R = 19.74 kΩ

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Required time constant

4.5 = 5·(1 − e−100/τ) → τ = 100/ln(5/(5 − 4.5))
τ = 100/2.303 = 43.43 ms

Resistance

kΩ times µF gives milliseconds.

R = τ/C = 43.43/2.2 = 19.74 kΩ

Answer

R = 19.74 kΩ
7.Series & parallel resistors

Answer: IR2 = 2.927 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 5 ΩR3​ = 6 Ω+−V1​30 VR2​4 ΩAR4​10 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 6 + 10 = 16 Ω
R2 ∥ 16 = 4·16/(4+16) = 3.2 Ω
Req = R1 + 3.2 = 5 + 3.2 = 8.2 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 30/8.2 = 3.659 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

VA = V1 − IR1·R1 = 30 − 3.659·5 = 11.71 V
IR2 = VA/R2 = 11.71/4 = 2.927 A

Answer

IR2 = 2.927 A
8.Series & parallel resistors

Answer: Req = 9.166 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 4 ΩR3​ = 20 ΩR5​ = 25 Ω+−V1​36 VR2​6 ΩAR4​30 ΩBR6​15 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 25 + 15 = 40 Ω
R4 ∥ 40 = 17.14 Ω
R3 + 17.14 = 37.14 Ω
R2 ∥ 37.14 = 5.166 Ω
Req = R1 + 5.166 = 4 + 5.166 = 9.166 Ω

Answer

Req = 9.166 Ω
9.DC-DC converters

Answer: L = 300 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 36/48 = 0.75

Inductance

L = 12·0.75/(1.5·20·10³) = 300 µH

Answer

L = 300 µH
10.DC-DC converters

Answer: Lcrit = 5.625 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 1 − 12/16 = 0.25

Boundary condition

Set the average inductor current equal to half the ripple current and solve for L.

Lcrit = D(1 − D)²·R/(2f)

Critical inductance

Lcrit = 0.25(1 − 0.25)²·20/(2250·10³) = 5.625 µH

Answer

Lcrit = 5.625 µH
11.Wheatstone bridge & strain gauges

Answer: Pg = 75.76 mW

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Voltage across the gauge

V = 10/2 = 5 V

Power

Pg = 5²/330 = 75.76 mW

Answer

Pg = 75.76 mW
12.Wheatstone bridge & strain gauges

Answer: Vo = 2.46 mV

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Relative resistance change

ΔR/R = 2.05·800·10⁻⁶ = 0.00164

Bridge output

Vo = Vs·GF·ε/2 = 3·0.00164/2 = 2.46 mV

Answer

Vo = 2.46 mV
13.Digital logic: gates, K-maps & flip-flops

Answer: AB = 11, CD = 11

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Neighbours of each 1

A 1 with a neighbouring 1 can join a group of two or more.

m15: m14, m13, m11, m7 → 0
ABCD0001111000011110111111111

The isolated 1

m15 = ABCD → AB = 11, CD = 11

Answer

AB = 11, CD = 11
14.Digital logic: gates, K-maps & flip-flops

Answer: N = 5

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Prime implicants

The largest groups that can be formed from 1s and Xs.

C′D′, BC′, A′D′, A′C′, A′B, AB′CD
ABCD000111100001111010110312X415X716X121130150141809111010

Minimal cover

F = C′D′ + BC′ + A′D′ + A′C′ + AB′CD
N = 5

Answer

N = 5

ExamProblems · examproblems.com/courses/electronics-1