Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−15 V680 Ω5.1 V1000 ΩIZ​ = ?

A 5.1 V Zener regulator is fed from 15 V through 680 Ω and supplies a 1000 Ω load. Find the Zener current IZ.

Vin = 15 VVZ = 5.1 VR = 680 ΩRL = 1000 Ω
IZ = mA
2.Diodes & transistorsHard
RC​ = 220 Ωβ = 80VCC​ = 12 V3.3 VRB​ = ?

An NPN transistor with β = 80 switches a 220 Ω load resistor connected between VCC = 12 V and its collector. The emitter is grounded. The base is driven from a 3.3 V logic output through a base resistor RB. Take VBE = 0.7 V and VCE(sat) = 0.2 V. Find the largest base resistor RB, in kΩ, that still drives the transistor just into saturation.

VCC = 12 VRC = 220 Ωβ = 80Vin = 3.3 VVBE = 0.7 VVCE(sat) = 0.2 V
RB = kΩ
3.Op-amp circuitsMedium
−+Vout​Rf​ = 2 kΩR1​ = 2 kΩVin​ = −0.3 V

The op-amp is ideal and runs from ±15 V supplies. Find the output voltage Vout.

Vin = −0.3 VR1 = 2 kΩRf = 2 kΩ
Vout = V
4.Op-amp circuitsHard
−+Vout​Rf​ = 22 kΩV1​ = −0.5 VR1​ = 4.7 kΩV2​ = 0.9 VR2​ = 10 kΩIf​

The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the current If through the feedback resistor, flowing towards the output.

V1 = −0.5 VV2 = 0.9 VR1 = 4.7 kΩR2 = 10 kΩRf = 22 kΩ
If = mA
5.RC & RL transientsMedium
+−Vs​12 Vt = 0R1​ = 10 kΩR2​ = 1 kΩC68 µF+−vC​

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the capacitor voltage vC at t = 150 ms.

Vs = 12 VR1 = 10 kΩR2 = 1 kΩC = 68 µFt = 150 ms
vC = V
6.RC & RL transientsHard
+−Vs​15 Vt = 0R = 2.2 kΩC10 µF+−vC​vC​(0) = 4 V

Just before the switch closes at t = 0, the capacitor holds 4 V with the polarity shown. How long does it take for vC to reach 7.3 V? Find t.

Vs = 15 VR = 2.2 kΩC = 10 µFvC(0) = 4 V
t = ms
7.Series & parallel resistorsMedium
R1​ = 10 ΩR3​ = 6 Ω+−V1​10 VR2​3 ΩAR4​5 ΩB

Find the equivalent resistance Req seen by the source V1.

V1 = 10 VR1 = 10 ΩR2 = 3 ΩR3 = 6 ΩR4 = 5 Ω
Req = Ω
8.Series & parallel resistorsHard
R1​ = 2 ΩR3​ = 30 ΩR5​ = 25 Ω+−V1​30 VR2​2 ΩAR4​6 ΩBR6​12 Ω

Find the equivalent resistance Req seen by the source V1.

V1 = 30 VR1 = 2 ΩR2 = 2 ΩR3 = 30 ΩR4 = 6 ΩR5 = 25 ΩR6 = 12 Ω
Req = Ω
9.DC-DC convertersMedium
+−15 VSL = ?CR+−4.5 V

An ideal buck converter turns 15 V into 4.5 V at a switching frequency of 20 kHz. Find the inductance L that keeps the peak-to-peak inductor ripple current at 0.2 A.

Vin​ = 15 VVo​ = 4.5 Vf = 20 kHzΔIL = 0.2 A
L = µH
10.DC-DC convertersHard
+−12 VLSC = 10 µFR = 50 Ω+−40 V

An ideal boost converter turns 12 V into 40 V for a 50 Ω load at 250 kHz. The output capacitor is 10 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 12 VVo​ = 40 Vf = 250 kHzC = 10 µFR = 50 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−6 V330 Ω330 Ω + ΔR330 Ω330 Ωab+−Vab​ = ?

A bridge has four 330 Ω arms and Vs = 6 V. The sensor R₂ increases by ΔR = 0.825 Ω. Using the small-change approximation, find the output Vab in mV.

Vs = 6 VR = 330 ΩΔR = 0.825 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−10 V120 Ω120 Ω + ΔR120 Ω120 Ωab+−3.844 mV

A strain gauge (GF = 2.05) on a member with E = 200 GPa forms a quarter bridge excited with 10 V. The output reads 3.844 mV. Find the axial stress σ in MPa.

Vs = 10 VGF = 2.05Vo = 3.844 mVE = 200 GPa
σ = MPa
13.Digital logic: gates, K-maps & flip-flopsMedium
ABC000111100101324576

Simplify F = BC′ + AB′C′ + B′C′ to its minimal sum-of-products form. How many literals L does the simplified expression contain?

F = BC′ + AB′C′ + B′C′
L =
14.Digital logic: gates, K-maps & flip-flopsHard
ABCD00011110000111100001030204050716X1211301511418X9X11110

Find the minimal SOP form of F(A, B, C, D) = Σm(6, 8, 10, 13, 14) + d(9, 11, 12), where d marks the don't-care conditions. How many literals L does it contain?

F(A, B, C, D) = Σm(6, 8, 10, 13, 14) + d(9, 11, 12)
L =

3Solutions

1.Diodes & transistors

Answer: IZ = 9.459 mA

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Resistor current

IR = 9.9/680 = 14.56 mA

Load current

IL = 5.1/1000 = 5.1 mA

Zener current

IZ = 14.56 − 5.1 = 9.459 mA

Answer

IZ = 9.459 mA
2.Diodes & transistors

Answer: RB = 3.878 kΩ

BJT as a switch: to switch a load fully on, the transistor is driven into saturation, where VCE = VCE(sat) and the collector current is set by the load: IC(sat) = (VCC − VCE(sat))/RC. Saturation needs at least IB = IC(sat)/β. If the base current is smaller, the transistor stays active and IC = β·IB.

Collector current in saturation

IC(sat) = (12 − 0.2)/220 = 53.64 mA

Minimum base current

IB(min) = IC(sat)/β = 53.64/80 = 670.5 µA

Base resistor

RB = (3.3 − 0.7)/IB = 2.6 V/0.6705 mA = 3.878 kΩ

Answer

RB = 3.878 kΩ

Any smaller base resistor also saturates the transistor; in practice you pick one a few times smaller.

3.Op-amp circuits

Answer: Vout = −0.6 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Inverting input follows the input

V₋ = V₊ = −0.3 V
I = V₋/R1 = −0.3/2 = −0.15 mA

Output voltage

The current through R₁ also flows through Rf.

Vout = V₋ + I·Rf = −0.3 + (−0.15)·2 = −0.6 V

Answer

Vout = −0.6 V
4.Op-amp circuits

Answer: If = −0.01638 mA

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input currents

V₋ = 0, so each input resistor has its full input voltage across it.

I1 = V1/R1 = −0.5/4.7 = −0.1064 mA
I2 = V2/R2 = 0.9/10 = 0.09 mA
If = I1 + I2 = −0.01638 mA

Answer

If = −0.01638 mA
5.RC & RL transients

Answer: vC = 0.9945 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find Rth; open the capacitor to find the voltage it will settle at.

Rth = R1 ∥ R2 = 10·1/(10 + 1) = 0.9091 kΩ
vC(∞) = 12·1/(10 + 1) = 1.091 V

Time constant

τ = Rth·C = 0.9091·68 = 61.82 ms

Charging curve

vC(t) = 1.091·(1 − e−150/61.82) = 0.9945 V

Answer

vC = 0.9945 V
6.RC & RL transients

Answer: t = 7.847 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 4 V, vC(∞) = Vs = 15 V
τ = R·C = 2.2 kΩ · 10 µF = 22 ms
vC(t) = 15 + (4 − 15)·e−t/τ

Solve for the time

7.3 = 15 + (−11)·e−t/τ → e−t/τ = (7.3 − 15)/(4 − 15) = 0.7
t = τ·ln((4 − 15)/(7.3 − 15)) = 22·ln(1.429) = 7.847 ms

Answer

t = 7.847 ms
7.Series & parallel resistors

Answer: Req = 12.36 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 10 ΩR3​ = 6 Ω+−V1​10 VR2​3 ΩAR4​5 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 6 + 5 = 11 Ω
R2 ∥ 11 = 3·11/(3+11) = 2.357 Ω
Req = R1 + 2.357 = 10 + 2.357 = 12.36 Ω

Answer

Req = 12.36 Ω
8.Series & parallel resistors

Answer: Req = 3.892 Ω

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 2 ΩR3​ = 30 ΩR5​ = 25 Ω+−V1​30 VR2​2 ΩAR4​6 ΩBR6​12 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 25 + 12 = 37 Ω
R4 ∥ 37 = 5.163 Ω
R3 + 5.163 = 35.16 Ω
R2 ∥ 35.16 = 1.892 Ω
Req = R1 + 1.892 = 2 + 1.892 = 3.892 Ω

Answer

Req = 3.892 Ω
9.DC-DC converters

Answer: L = 787.5 µH

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 4.5/15 = 0.3

Inductance

L = 10.5·0.3/(0.2·20·10³) = 787.5 µH

Answer

L = 787.5 µH
10.DC-DC converters

Answer: ΔVo = 224 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 1 − 12/40 = 0.7

Load current

Io = 40/50 = 0.8 A

Output ripple

ΔVo = 0.8·0.7/(250·10³·10·10⁻⁶) = 224 mV

Answer

ΔVo = 224 mV
11.Wheatstone bridge & strain gauges

Answer: Vab = 3.75 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Relative change

ΔR/R = 0.825/330 = 0.0025

Linearised output

Vab ≈ 6·0.0025/4 = 3.75 mV

Answer

Vab = 3.75 mV

The exact value is 3.745 mV; the approximation is good while ΔR/R is small.

12.Wheatstone bridge & strain gauges

Answer: σ = 150 MPa

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Strain

ε = 4·0.003844/(10·2.05) = 0.00075

Stress

σ = 200·10³ MPa·0.00075 = 150 MPa

Answer

σ = 150 MPa
13.Digital logic: gates, K-maps & flip-flops

Answer: L = 1

Boolean algebra: the rules that simplify expressions are X + X′ = 1 and X·X′ = 0, X + X = X, absorption X + X·Y = X, the combining rule X·Y + X·Y′ = X, X + X′Y = X + Y and the consensus theorem XY + X′Z + YZ = XY + X′Z. De Morgan's laws turn (X·Y)′ into X′ + Y′ and (X + Y)′ into X′·Y′. A Karnaugh map applies these rules graphically: every group of two neighbouring cells is one use of XY + XY′ = X.

Minterms of the expression

BC′ → m(2, 6)
AB′C′ → m(4)
B′C′ → m(0, 4)
ABC00011110011001031214050716

Group and read off

F = C′

Count the literals

L = 1

Answer

L = 1
14.Digital logic: gates, K-maps & flip-flops

Answer: L = 7

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Prime implicants

The largest groups that can be formed from 1s and Xs.

BCD′, AD′, AC′, AB′
ABCD00011110000111100001030204050716X1211301511418X9X11110

Minimal cover

F = BCD′ + AD′ + AC′
L = 7

Answer

L = 7

Another grouping of the same size exists; it has the same number of terms and literals.

ExamProblems · examproblems.com/courses/electronics-1