Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.
Wheatstone bridge & strain gauges
Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε
Method
Treat the bridge as two voltage dividers across the same supply.
For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.
Digital logic: gates, K-maps & flip-flops
Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states
Method
For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.
2Practice problems
1.Diodes & transistorsMedium
An NPN transistor with β = 150 has voltage-divider bias from VCC = 15 V: R₁ = 68 kΩ from VCC to the base and R₂ = 12 kΩ from the base to ground. The collector resistor is RC = 1.5 kΩ and the emitter resistor is RE = 1 kΩ. Take VBE = 0.7 V and use the Thévenin equivalent of the divider (do not neglect the base current). Find the collector–emitter voltage VCE.
A 9.1 V Zener regulator must supply up to 50 mA to a load. The input can drop to 12 V, and the Zener needs at least 1 mA to regulate. Find the largest series resistance Rmax that keeps it regulating.
The op-amp is ideal and runs from ±15 V supplies; its output saturates at ±14 V. The non-inverting amplifier is driven by a sine wave. Find the largest input amplitude Vin,max (peak value) for which the output does not clip.
R1 = 4.7 kΩRf = 47 kΩVsat = ±14 V
Vin,max = V
4.Op-amp circuitsHard
The summing amplifier uses an ideal op-amp with ±15 V supplies. Find the output voltage Vout.
V1 = −1 VV2 = 1 VR1 = 1 kΩR2 = 47 kΩRf = 1 kΩ
Vout = V
5.RC & RL transientsMedium
The inductor carries no current before the switch closes at t = 0. Find the energy W stored in the inductor at t = 1 ms, in mJ.
Vs = 20 VR = 47 ΩL = 33 mHt = 1 ms
W = mJ
6.RC & RL transientsHard
The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage vC at t = 40 ms.
Vs = 12 VR1 = 3.3 kΩR2 = 1 kΩC = 47 µFt = 40 ms
vC = V
7.Series & parallel resistorsMedium
Find the current IR1 delivered by the source, which flows through R1.
V1 = 18 VR1 = 2 ΩR2 = 6 ΩR3 = 5 ΩR4 = 20 Ω
IR1 = A
8.Series & parallel resistorsHard
Find the equivalent resistance Req seen by the source V1.
An ideal buck converter turns 36 V into 25.2 V at 250 kHz with L = 220 µH. Find the peak-to-peak inductor ripple current ΔIL.
Vin = 36 VVo = 25.2 Vf = 250 kHzL = 220 µH
ΔIL = A
10.DC-DC convertersHard
An ideal buck-boost converter turns 12 V into −12 V for a 50 Ω load at 200 kHz. The output capacitor is 100 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.
A 200 Ω strain gauge is one arm (R₂) of a bridge with four equal 200 Ω arms and an excitation of 10 V. Find the power Pg dissipated in the gauge, in mW. Self-heating limits the excitation.
Vs = 10 VR = 200 Ω
Pg = mW
12.Wheatstone bridge & strain gaugesHard
A strain gauge (GF = 2.1) on a member with E = 110 GPa forms a quarter bridge excited with 2.5 V. The output reads 1.969 mV. Find the axial stress σ in MPa.
A 4-to-1 multiplexer has its select inputs S₁ = A and S₀ = B, and its data inputs tied to I₀ = 0, I₁ = C′, I₂ = 0, I₃ = 0. For how many of the 8 combinations of A, B and C is the output F = 1? Find N.
I₀ = 0I₁ = C′I₂ = 0I₃ = 0
N =
14.Digital logic: gates, K-maps & flip-flopsHard
For F(A, B, C, D) = Σm(0, 2, 9, 11, 14) + d(6, 7, 12, 13), where d marks the don't-care conditions, find the number N of essential prime implicants.
BJT bias point: in the active region VBE = 0.7 V, IC = β·IB and IE = (β + 1)·IB. Find IB from the base loop with KVL, then IC, then VCE from the collector–emitter loop. A voltage divider at the base is replaced by its Thévenin equivalent VTH = VCC·R₂/(R₁ + R₂), RTH = R₁∥R₂; an emitter resistor appears (β + 1) times larger in the base loop.
Thévenin equivalent of the divider
VTH = 15·12/(68 + 12) = 2.25 V
RTH = 68·12/(68 + 12) = 10.2 kΩ
Base current
KVL around the base loop; the emitter current is (β + 1)·IB.
IB = (2.25 − 0.7)/(10.2 + 151·1) = 9.615 µA
Collector current
IC = 150·9.615 µA = 1.442 mA
IE = 151·9.615 µA = 1.452 mA
Collector–emitter voltage
VCE = 15 − 1.442·1.5 − 1.452·1 = 11.38 V
Answer
VCE = 11.38 V
2.Diodes & transistors
Answer: Rmax = 56.86 Ω
Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.
Worst-case current
IR = 50 + 1 = 51 mA
Largest resistance
Rmax = 2.9/0.051 = 56.86 Ω
Answer
Rmax = 56.86 Ω
3.Op-amp circuits
Answer: Vin,max = 1.273 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Gain
Av = 1 + Rf/R1 = 1 + 47/4.7 = 11
Largest input before clipping
Vin,max = Vsat/|Av| = 14/11 = 1.273 V
Answer
Vin,max = 1.273 V
4.Op-amp circuits
Answer: Vout = 0.9787 V
Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.
Input currents
V₋ = 0, so each input resistor has its full input voltage across it.
I1 = V1/R1 = −1/1 = −1 mA
I2 = V2/R2 = 1/47 = 0.02128 mA
If = I1 + I2 = −0.9787 mA
Output voltage
Vout = −Rf·If = −1·(−0.9787) = 0.9787 V
Answer
Vout = 0.9787 V
5.RC & RL transients
Answer: W = 1.723 mJ
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant and final current
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
τ = L/R = 33 mH / 47 Ω = 0.7021 ms
i(∞) = Vs/R = 20/47 = 0.4255 A
Current at the given time
i(t) = 0.4255·(1 − e−1/0.7021) = 0.3231 A
Stored energy
W = ½·L·i² = ½·33·0.3231² = 1.723 mJ
Answer
W = 1.723 mJ
6.RC & RL transients
Answer: vC = 1.192 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Initial capacitor voltage
In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.
vC(0) = 12·1/(3.3 + 1) = 2.791 V
Time constant after the switch opens
τ = R2·C = 1·47 = 47 ms
Discharge
vC(t) = 2.791·e−40/47 = 1.192 V
Answer
vC = 1.192 V
7.Series & parallel resistors
Answer: IR1 = 2.632 A
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 5 + 20 = 25 Ω
R2 ∥ 25 = 6·25/(6+25) = 4.839 Ω
Req = R1 + 4.839 = 2 + 4.839 = 6.839 Ω
Current from the source
The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.
IR1 = V1/Req = 18/6.839 = 2.632 A
Answer
IR1 = 2.632 A
8.Series & parallel resistors
Answer: Req = 17.71 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 3 + 4 = 7 Ω
R4 ∥ 7 = 3.231 Ω
R3 + 3.231 = 28.23 Ω
R2 ∥ 28.23 = 2.712 Ω
Req = R1 + 2.712 = 15 + 2.712 = 17.71 Ω
Answer
Req = 17.71 Ω
9.DC-DC converters
Answer: ΔIL = 0.1375 A
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 25.2/36 = 0.7
Inductor voltage during the on-time
While S is on, the inductor sits between Vin and Vo.
VL = 36 − 25.2 = 10.8 V
Ripple current
ΔIL = VL·D/(L·f) = 10.8·0.7/(220·10⁻⁶·250·10³) = 0.1375 A
Answer
ΔIL = 0.1375 A
10.DC-DC converters
Answer: ΔVo = 6 mV
DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.
Duty cycle
D = 12/(12 + 12) = 0.5
Load current
Io = 12/50 = 0.24 A
Output ripple
ΔVo = 0.24·0.5/(200·10³·100·10⁻⁶) = 6 mV
Answer
ΔVo = 6 mV
11.Wheatstone bridge & strain gauges
Answer: Pg = 125 mW
Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.
Voltage across the gauge
V = 10/2 = 5 V
Power
Pg = 5²/200 = 125 mW
Answer
Pg = 125 mW
12.Wheatstone bridge & strain gauges
Answer: σ = 165 MPa
Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.
Strain
ε = 4·0.001969/(2.5·2.1) = 0.0015
Stress
σ = 110·10³ MPa·0.0015 = 165 MPa
Answer
σ = 165 MPa
13.Digital logic: gates, K-maps & flip-flops
Answer: N = 1
Multiplexer: a 2ⁿ-to-1 multiplexer passes one of its data inputs to the output; the select lines, read as a binary number, pick which one. For a 4-to-1 MUX with selects S₁S₀ = AB, F = A′B′·I₀ + A′B·I₁ + AB′·I₂ + AB·I₃. Tying the data inputs to 0, 1, C or C′ makes the MUX produce any function of A, B and C, which is a common way to build logic with one chip.
Output expression
F = A′BC′
Rows with F = 1
ABC = 010
N = 1
Answer
N = 1
14.Digital logic: gates, K-maps & flip-flops
Answer: N = 2
Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.
Prime implicants
The largest groups that can be formed from 1s and Xs.