Electronics 1: cram pack

Formula sheets, the key method steps for every topic and 14 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Diodes & transistors

Diode (constant drop)
VD = 0.7 V when conducting
Active region
VBE = 0.7 V, IC = β·IB, IE = (β + 1)·IB
Fixed bias
IB = (VCC − 0.7)/RB
Divider bias
IB = (VTH − 0.7)/(RTH + (β + 1)RE)
Thévenin of the divider
VTH = VCC·R2/(R1 + R2), RTH = R1∥R2
Collector loop
VCE = VCC − ICRC − IERE
Saturation
IC(sat) = (VCC − VCE(sat))/RC, IB ≥ IC(sat)/β

Op-amp circuits

Inverting amplifier
Vout = −(Rf/Rin)·Vin
Non-inverting amplifier
Vout = (1 + Rf/R1)·Vin
Summing amplifier
Vout = −Rf(V1/R1 + V2/R2)
Ideal op-amp
V+ = V−, Iin = 0

RC & RL transients

Time constant
τ = RC | τ = L/R
Response
x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
Capacitor at DC
open circuit; vC cannot jump
Inductor at DC
short circuit; iL cannot jump
Settled
t ≈ 5τ

Method

  1. Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
  2. Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
  3. Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
  4. Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.

Series & parallel resistors

Resistors in series
Req = R1 + R2 + …
Resistors in parallel
1/Req = 1/R1 + 1/R2 + …
Two in parallel
Req = R1R2 / (R1 + R2)
Ohm's law
V = I·R
Power
P = V·I = I²R = V²/R

Method

  1. Start at the end of the network furthest from the terminals.
  2. Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
  3. Redraw the circuit after each step.
  4. Repeat until one resistor is left between the terminals.

DC-DC converters

Buck
Vo = D·Vin
Boost
Vo = Vin/(1 − D)
Inverting buck-boost
|Vo| = Vin·D/(1 − D)
Ideal power balance
VinIin = VoIo
Inductor ripple
ΔIL = VL,on·D/(L·f); buck Vin − Vo, boost and buck-boost Vin
Average inductor current
buck Io; boost and buck-boost Io/(1 − D)
Output ripple
buck ΔIL/(8fC); boost and buck-boost Io·D/(fC)
CCM boundary
buck (1 − D)R/(2f); boost D(1 − D)²R/(2f); buck-boost (1 − D)²R/(2f)

Method

  1. Identify the converter (buck, boost or buck-boost) and the duty cycle D from the voltage ratio.
  2. Use volt-second balance on the inductor: the average inductor voltage over a period is zero.
  3. Find the inductor voltage while the switch is on, then ΔIL = VL·D/(L·f).
  4. For the output ripple, find the charge that flows in and out of the capacitor; for the CCM boundary, set the average inductor current equal to ΔIL/2.

Wheatstone bridge & strain gauges

Divider voltages
Va = VsR2/(R1 + R2), Vb = VsR4/(R3 + R4)
Output
Vab = Va − Vb
Balance
R1/R2 = R3/R4
Slide-wire bridge
R/Rx = l/(100 − l)
Thévenin resistance
Rth = R1∥R2 + R3∥R4
Gauge factor
ΔR/R = GF·ε
Bridge output
quarter Vs·GF·ε/4, half Vs·GF·ε/2, full Vs·GF·ε
Small change, one arm
Vab ≈ Vs·ΔR/(4R)
Stress
σ = E·ε

Method

  1. Treat the bridge as two voltage dividers across the same supply.
  2. For balance, set R₁/R₂ = R₃/R₄ and solve for the unknown resistor.
  3. For an unbalanced bridge, find Va and Vb from the dividers and subtract; use the Thévenin equivalent when a meter loads the output.
  4. For strain gauges, convert strain to ΔR/R = GF·ε and use Vs·GF·ε/4, /2 or ×1 for a quarter, half or full bridge.

Digital logic: gates, K-maps & flip-flops

Basic gates
A·B, A + B, A′, (A·B)′, (A + B)′, A ⊕ B
Boolean rules
X + X′ = 1, X·X′ = 0, X + XY = X, XY + XY′ = X
De Morgan
(X·Y)′ = X′ + Y′, (X + Y)′ = X′·Y′
Karnaugh map order
00, 01, 11, 10 (Gray code)
Group of 2ᵏ cells
loses k variables
4-to-1 multiplexer
F = A′B′I0 + A′BI1 + AB′I2 + ABI3
Flip-flops
D: Q⁺ = D, T: Q⁺ = T ⊕ Q, JK: Q⁺ = JQ′ + K′Q
Counters
n-bit: 2ⁿ states; mod-N: smallest n with 2ⁿ ≥ N; fout = fclk/N
Ripple counter
fmax = 1/(n·tpd)
Ring and Johnson counters
n and 2n states

Method

  1. For a circuit, work from the inputs to the output one gate at a time and write the value on every wire, or write its expression and fill in the truth table.
  2. For simplification, put the 1s (and the don’t-cares as X) into a Karnaugh map with Gray-code rows and columns: 00, 01, 11, 10.
  3. Cover the 1s with as few and as large groups of 1, 2, 4, 8 or 16 cells as possible, wrapping round the edges; each group is one product term made of the variables that stay constant. Group the 0s for the POS form.
  4. For flip-flops and counters, read the inputs at each active clock edge, write the state after every edge, and remember that an n-bit counter wraps round after 2ⁿ states.

2Practice problems

1.Diodes & transistorsMedium
+−15 V330 Ω5.1 V1500 ΩIZ​ = ?

A 5.1 V Zener regulator is fed from 15 V through 330 Ω and supplies a 1500 Ω load. Find the Zener current IZ.

Vin = 15 VVZ = 5.1 VR = 330 ΩRL = 1500 Ω
IZ = mA
2.Diodes & transistorsHard
+−≤ 27 V100 Ω6.2 V

A 6.2 V Zener regulator has a 100 Ω series resistor. The input can rise to 27 V, and the load may be disconnected. Find the largest power PZ,max the Zener must dissipate.

Vin,max = 27 VVZ = 6.2 VR = 100 Ω
PZ,max = mW
3.Op-amp circuitsMedium
−+Vout​Rf​ = 47 kΩR1​ = 10 kΩVin​

The op-amp is ideal and runs from ±15 V supplies; its output saturates at ±14 V. The non-inverting amplifier is driven by a sine wave. Find the largest input amplitude Vin,max (peak value) for which the output does not clip.

R1 = 10 kΩRf = 47 kΩVsat = ±14 V
Vin,max = V
4.Op-amp circuitsHard
−+Vout​C = 0.22 µFVin​ = −2 VR = 10 kΩ

The integrator uses an ideal op-amp with ±15 V supplies; its output saturates at ±12 V. The capacitor is uncharged when a constant input Vin = −2 V is applied at t = 0. Find the output voltage Vout at t = 1 ms.

Vin = −2 VR = 10 kΩC = 0.22 µFVsat = ±12 Vt = 1 ms
Vout = V
5.RC & RL transientsMedium
+−Vs​30 Vt = 0R1​ = 1 kΩR2​ = 6.8 kΩC100 µF+−vC​

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the capacitor voltage vC at t = 150 ms.

Vs = 30 VR1 = 1 kΩR2 = 6.8 kΩC = 100 µFt = 150 ms
vC = V
6.RC & RL transientsHard
+−Vs​20 Vt = 0R = 4.7 kΩC68 µF+−vC​vC​(0) = 4 V

Just before the switch closes at t = 0, the capacitor holds 4 V with the polarity shown. Find the capacitor voltage vC at t = 80 ms.

Vs = 20 VR = 4.7 kΩC = 68 µFvC(0) = 4 Vt = 80 ms
vC = V
7.Series & parallel resistorsMedium
R1​ = 2 ΩIR1​R3​ = 5 Ω+−V1​6 VR2​8 ΩAR4​6 ΩB

Find the current IR1 delivered by the source, which flows through R1.

V1 = 6 VR1 = 2 ΩR2 = 8 ΩR3 = 5 ΩR4 = 6 Ω
IR1 = A
8.Series & parallel resistorsHard
R1​ = 25 ΩIR1​R3​ = 3 ΩR5​ = 6 Ω+−V1​18 VR2​20 ΩAR4​30 ΩBR6​15 Ω

Find the current IR1 delivered by the source, which flows through R1.

V1 = 18 VR1 = 25 ΩR2 = 20 ΩR3 = 3 ΩR4 = 30 ΩR5 = 6 ΩR6 = 15 Ω
IR1 = A
9.DC-DC convertersMedium
tiL​Imax​ = ?Imin​Io​DTT2T

A buck converter turns 15 V into 7.5 V for a 4 Ω load. It switches at 500 kHz with L = 22 µH. Find the peak inductor current Imax.

Vin​ = 15 VVo​ = 7.5 Vf = 500 kHzL = 22 µHR = 4 Ω
Imax = A
10.DC-DC convertersHard
+−12 VLSC = 10 µFR = 20 Ω+−24 V

An ideal boost converter turns 12 V into 24 V for a 20 Ω load at 40 kHz. The output capacitor is 10 µF. Find the peak-to-peak output voltage ripple ΔVo in mV.

Vin​ = 12 VVo​ = 24 Vf = 40 kHzC = 10 µFR = 20 Ω
ΔVo = mV
11.Wheatstone bridge & strain gaugesMedium
+−10 V330 Ω330 Ω + ΔR330 Ω330 Ωab+−Vab​ = ?

A bridge has four 330 Ω arms and Vs = 10 V. The sensor R₂ increases by ΔR = 49.5 Ω. Find the exact output Vab in mV.

Vs = 10 VR = 330 ΩΔR = 49.5 Ω
Vab = mV
12.Wheatstone bridge & strain gaugesHard
+−5 V120 Ω120 Ω + ΔR120 Ω120 Ωab+−Vo​

A quarter bridge (one active gauge, GF = 2.1) is excited with 5 V. The largest strain to be measured is 250 µε, and it must give 10 V at the input of an analogue-to-digital converter. Find the amplifier gain G.

Vs = 5 VGF = 2.1εmax = 250 µεVFS = 10 V
G =
13.Digital logic: gates, K-maps & flip-flopsMedium
ABC00011110010001031204150716

Use the Karnaugh map to find the minimal product-of-sums (POS) form of F(A, B, C) = Σm(2, 5, 6). How many sum terms (factors) N does it have?

F(A, B, C) = Σm(2, 5, 6)
N =
14.Digital logic: gates, K-maps & flip-flopsHard
ABCD000111100001111010110302040507X60120131151140819X11X10

Find the minimal SOP form of F(A, B, C, D) = Σm(0, 1, 9, 14, 15) + d(6, 10, 11), where d marks the don't-care conditions. How many product terms N does it have?

F(A, B, C, D) = Σm(0, 1, 9, 14, 15) + d(6, 10, 11)
N =

3Solutions

1.Diodes & transistors

Answer: IZ = 26.6 mA

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Resistor current

IR = 9.9/330 = 30 mA

Load current

IL = 5.1/1500 = 3.4 mA

Zener current

IZ = 30 − 3.4 = 26.6 mA

Answer

IZ = 26.6 mA
2.Diodes & transistors

Answer: PZ,max = 1290 mW

Zener regulator: a reverse-biased Zener diode holds its voltage VZ while its current stays above a minimum IZ,min. The series resistor R takes the difference between input and output: IR = (Vin − VZ)/R. That current splits between the load, IL = VZ/RL, and the Zener: IZ = IR − IL. Design for the worst cases: the lowest input with the largest load must still leave IZ,min, and the highest input with no load gives the largest Zener power PZ = VZ·IZ.

Worst-case Zener current

IZ = 20.8/100 = 208 mA

Zener power

PZ = 6.2·208 = 1290 mW

Answer

PZ,max = 1290 mW
3.Op-amp circuits

Answer: Vin,max = 2.456 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Gain

Av = 1 + Rf/R1 = 1 + 47/10 = 5.7

Largest input before clipping

Vin,max = Vsat/|Av| = 14/5.7 = 2.456 V

Answer

Vin,max = 2.456 V
4.Op-amp circuits

Answer: Vout = 0.9091 V

Ideal op-amp rules: with negative feedback, the op-amp drives its output so that its two inputs sit at the same voltage (V₋ = V₊), and no current flows into either input. Writing KCL at the inverting input with these two facts gives the output.

Input current and ramp rate

kΩ times µF gives milliseconds.

RC = 10 kΩ · 0.22 µF = 2.2 ms
ramp rate = −Vin/(RC) = −(−2)/2.2 = 0.9091 V/ms

Output at the given time

The ideal value lies inside ±Vsat, so the integrator has not clipped yet.

Vout = −Vin·t/(RC) = −(−2)·1/2.2 = 0.9091 V

Answer

Vout = 0.9091 V
5.RC & RL transients

Answer: vC = 21.47 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find Rth; open the capacitor to find the voltage it will settle at.

Rth = R1 ∥ R2 = 1·6.8/(1 + 6.8) = 0.8718 kΩ
vC(∞) = 30·6.8/(1 + 6.8) = 26.15 V

Time constant

τ = Rth·C = 0.8718·100 = 87.18 ms

Charging curve

vC(t) = 26.15·(1 − e−150/87.18) = 21.47 V

Answer

vC = 21.47 V
6.RC & RL transients

Answer: vC = 7.543 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Initial value, final value, time constant

The capacitor voltage cannot jump, so it starts at its stored value and heads for the source voltage.

vC(0) = 4 V, vC(∞) = Vs = 20 V
τ = R·C = 4.7 kΩ · 68 µF = 319.6 ms
vC(t) = 20 + (4 − 20)·e−t/τ

Voltage at the given time

vC(80) = 20 + (−16)·e−80/319.6 = 7.543 V

Answer

vC = 7.543 V
7.Series & parallel resistors

Answer: IR1 = 0.9048 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 2 ΩR3​ = 5 Ω+−V1​6 VR2​8 ΩAR4​6 ΩB

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R3 + R4 = 5 + 6 = 11 Ω
R2 ∥ 11 = 8·11/(8+11) = 4.632 Ω
Req = R1 + 4.632 = 2 + 4.632 = 6.632 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 6/6.632 = 0.9048 A

Answer

IR1 = 0.9048 A
8.Series & parallel resistors

Answer: IR1 = 0.5344 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

R1​ = 25 ΩR3​ = 3 ΩR5​ = 6 Ω+−V1​18 VR2​20 ΩAR4​30 ΩBR6​15 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R5 + R6 = 6 + 15 = 21 Ω
R4 ∥ 21 = 12.35 Ω
R3 + 12.35 = 15.35 Ω
R2 ∥ 15.35 = 8.686 Ω
Req = R1 + 8.686 = 25 + 8.686 = 33.69 Ω

Current from the source

The source sees only Req, so Ohm’s law gives the current it delivers. That current flows through R₁.

IR1 = V1/Req = 18/33.69 = 0.5344 A

Answer

IR1 = 0.5344 A
9.DC-DC converters

Answer: Imax = 2.045 A

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 7.5/15 = 0.5

Average and ripple current

Io = 7.5/4 = 1.875 A
ΔIL = VL·D/(L·f) = 7.5·0.5/(22·10⁻⁶·500·10³) = 0.3409 A

Peak current

Imax = 1.875 + 0.3409/2 = 2.045 A

Answer

Imax = 2.045 A
10.DC-DC converters

Answer: ΔVo = 1500 mV

DC-DC converters: a switch S turns on for the fraction D of each period T = 1/f. In steady state the average inductor voltage is zero (volt-second balance), which gives the ideal conversion ratios in continuous conduction: buck Vo = D·Vin, boost Vo = Vin/(1 − D), inverting buck-boost |Vo| = Vin·D/(1 − D). An ideal converter keeps the power: Vin·Iin = Vo·Io. While S is on the inductor current rises by ΔIL = VL·D·T/L, with VL = Vin − Vo for the buck and Vin for the boost and buck-boost. The output ripple is ΔVo = ΔIL/(8fC) for the buck and Io·D/(fC) for the boost and buck-boost. The inductor current just touches zero (the CCM boundary) when the average inductor current equals ΔIL/2.

Duty cycle

D = 1 − 12/24 = 0.5

Load current

Io = 24/20 = 1.2 A

Output ripple

ΔVo = 1.2·0.5/(40·10³·10·10⁻⁶) = 1500 mV

Answer

ΔVo = 1500 mV
11.Wheatstone bridge & strain gauges

Answer: Vab = 348.8 mV

Wheatstone bridge: two voltage dividers share one supply Vs. The left divider R1–R2 gives Va = Vs·R2/(R1 + R2) and the right divider R3–R4 gives Vb = Vs·R4/(R3 + R4); the output is Vab = Va − Vb. The bridge is balanced (Vab = 0, no current in the meter) when R1/R2 = R3/R4, that is R1·R4 = R2·R3. Seen from the output, the bridge is a Thévenin source with Rth = R1∥R2 + R3∥R4.

Node voltages

Va = 10·379.5/709.5 = 5.349 V
Vb = 5 V

Output

Vab = 348.8 mV

Answer

Vab = 348.8 mV

The linear estimate Vs·ΔR/(4R) = 375 mV is 7.5 % too high: a quarter bridge is not quite linear.

12.Wheatstone bridge & strain gauges

Answer: G = 15238

Strain gauges: a gauge changes its resistance with strain: ΔR/R = GF·ε, where the gauge factor GF is about 2 for metal foil. In a bridge with all arms equal to R, one active gauge (quarter bridge) gives Vo ≈ Vs·GF·ε/4. Two active gauges with opposite strains in adjacent arms (half bridge) give Vs·GF·ε/2, and four (full bridge) give Vs·GF·ε. Stress follows from Hooke’s law, σ = E·ε. Load cells state their sensitivity in mV/V: the output at full load per volt of excitation.

Bridge output at full scale

Vo = 0.6563 mV

Gain

G = 10/0.0006563 = 15238

Answer

G = 15238
13.Digital logic: gates, K-maps & flip-flops

Answer: N = 3

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

ABC00011110010001031204150716

Group the 0s

Every group is a rectangle of 2ᵏ cells; edge cells are neighbours of the cells on the opposite edge.

(B + C)
(B′ + C′)
(A + C′)

Minimal POS form

F = (B + C)(B′ + C′)(A + C′)
N = 3

Answer

N = 3

Another grouping of the same size exists; it has the same number of terms and literals.

14.Digital logic: gates, K-maps & flip-flops

Answer: N = 3

Karnaugh maps: the cells are ordered in Gray code (00, 01, 11, 10), so neighbouring cells, including the ones across the edges, differ in exactly one variable. Group the 1s in rectangles of 1, 2, 4, 8 or 16 cells, as large as possible and as few as possible, until every 1 is covered. Each group is one product term: the variables that stay constant inside it. A group of 2ᵏ cells loses k variables. Don't-cares (X) may be used to make groups bigger but never have to be covered. Grouping the 0s instead gives the minimal POS form.

Prime implicants

The largest groups that can be formed from 1s and Xs.

B′C′D, BCD′, AC, AB′D, A′B′C′
ABCD000111100001111010110302040507X60120131151140819X11X10

Minimal cover

F = B′C′D + AC + A′B′C′
N = 3

Answer

N = 3

Another grouping of the same size exists; it has the same number of terms and literals.

ExamProblems · examproblems.com/courses/electronics-1