FE Civil exam practice: cram pack

Static equilibrium: a body at rest has ΣF_x = 0, ΣF_y = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

Static equilibrium: a body at rest has ΣF_x = 0, ΣF_y = 0 and ΣM = 0 about any point. Taking moments about one support removes that support’s reaction from the equation.

Zero-force members: at a joint, the forces must balance in every direction. If a joint has no load and no support, and two of its three members are in line, then the balance across that line involves only the third member, so its force is zero. If only two members meet at an unloaded joint and they are not in line, both are zero.

Method of joints: every pin of a truss is in equilibrium, so ΣF_x = 0 and ΣF_y = 0 at each joint. Start at a joint with at most two unknown member forces. A negative result means the member is in compression.

Largest bending moment: M changes slope wherever the shear force changes, so its peaks sit where the shear force crosses zero: under a point load, inside a distributed load, or over a support of an overhang. At a fixed support of a cantilever the moment is largest at the wall. Compare the size of M at those places, sagging or hogging.

Method of sections: cut the beam where you want the internal forces and keep one side. The shear force V balances the vertical forces on that side, and the bending moment M balances their moments about the cut.

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition).

Beam deflection: deflections come from integrating the curvature M/(EI) twice. Standard cases are tabulated, for example PL³/(3EI) for a cantilever with an end load and 5wL⁴/(384EI) for a simply supported beam under a full uniform load. Deflections from separate loads add (superposition). For a statically indeterminate beam, remove a redundant support and require the deflection there to be zero (compatibility).

Euler buckling: a slender column becomes unstable at P_cr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Euler buckling: a slender column becomes unstable at P_cr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Second moment of area: for a rectangle about its own centroidal axis I = bh³/12, and about its base bh³/3 (parallel-axis theorem I = I_c + A·d²). A hole is handled by subtracting its I, as long as both parts share the same axis. The elastic section modulus is S = I/c, where c is the distance to the extreme fibre.

Sections with holes: treat a hole as a negative area. The centroid is ȳ = (A₁y₁ − A₂y₂)/(A₁ − A₂), with A₁, y₁ for the full plate and A₂, y₂ for the hole. For the second moment of area about the centroidal axis, use the parallel-axis theorem for each part and subtract the hole: I = (I_c1 + A₁d₁²) − (I_c2 + A₂d₂²), where d is the distance from each part's own centroid to the axis through ȳ. A rectangle has I_c = bh³/12 and a circle I_c = πd⁴/64.

Effective stress (Terzaghi): the soil skeleton carries σ′ = σ − u. The total stress σ is the weight of everything above the point, Σγ·h, using the dry unit weight above the water table and the saturated unit weight below it. Below the water table the pore water pressure is hydrostatic: u = γ_w·(depth below the water table).

Effective stress (Terzaghi): the soil skeleton carries σ′ = σ − u. The total stress σ is the weight of everything above the point, Σγ·h, using the dry unit weight above the water table and the saturated unit weight below it. Below the water table the pore water pressure is hydrostatic: u = γ_w·(depth below the water table).

Primary consolidation of a clay layer of thickness H, using the effective stress at the middle of the layer: σ′_f = σ′₀ + Δσ. Normally consolidated clay: S = C_c·H/(1 + e₀)·log₁₀(σ′_f/σ′₀). Overconsolidated clay recompresses along C_r up to the preconsolidation pressure σ′_p and follows C_c only beyond it. Time: t = T_v·H_dr²/c_v, where the drainage path H_dr is H/2 when water can leave at the top and bottom, and H when only one side drains.

Primary consolidation of a clay layer of thickness H, using the effective stress at the middle of the layer: σ′_f = σ′₀ + Δσ. Normally consolidated clay: S = C_c·H/(1 + e₀)·log₁₀(σ′_f/σ′₀). Overconsolidated clay recompresses along C_r up to the preconsolidation pressure σ′_p and follows C_c only beyond it. Time: t = T_v·H_dr²/c_v, where the drainage path H_dr is H/2 when water can leave at the top and bottom, and H when only one side drains.

Hydrostatic force on a plane surface: F = ρ·g·y_c·A. It acts at the centre of pressure, y_cp = y_c + I_c/(y_cA), which always lies below the centroid.

Hydrostatic force on a plane surface: F = ρ·g·y_c·A. It acts at the centre of pressure, y_cp = y_c + I_c/(y_cA), which always lies below the centroid.

Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss h_f = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses h_m = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = h_f + h_m, with the exit loss K = 1 included.

Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss h_f = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses h_m = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = h_f + h_m, with the exit loss K = 1 included.

Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R^2/3·S^1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.

Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R^2/3·S^1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.

Pump power: the power given to the water is the hydraulic power P_h = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: P_shaft = P_h/η_pump, and the motor draws P_el = P_shaft/η_motor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.

Pump power: the power given to the water is the hydraulic power P_h = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: P_shaft = P_h/η_pump, and the motor draws P_el = P_shaft/η_motor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.

Time value of money: money today is worth more than the same amount later, because it can earn interest. With interest rate i per period, an amount grows as FV = PV·(1 + i)ⁿ. A series of equal payments (an annuity) is valued by adding up each payment, which gives the annuity formulas.

Time value of money: money today is worth more than the same amount later, because it can earn interest. With interest rate i per period, an amount grows as FV = PV·(1 + i)ⁿ. A series of equal payments (an annuity) is valued by adding up each payment, which gives the annuity formulas.

Net present value: discount every cash flow back to today with the required rate of return r, then add them up: NPV = Σ CFₜ/(1 + r)ᵗ. A project with NPV > 0 earns more than r and adds value. The internal rate of return (IRR) is the rate at which NPV = 0.

Net present value: discount every cash flow back to today with the required rate of return r, then add them up: NPV = Σ CFₜ/(1 + r)ᵗ. A project with NPV > 0 earns more than r and adds value. The internal rate of return (IRR) is the rate at which NPV = 0.

Normal distribution: convert a value x to a z-score, z = (x − μ)/σ, which counts standard deviations from the mean. A z-table (or Φ(z)) gives the area to the left of z, which is P(X < x). The area to the right is 1 − Φ(z), and the area between two values is the difference of their two areas.

Sums and differences of normal variables: if X and Y are independent and normal, X + Y and X − Y are normal too. Means add or subtract: E(X ± Y) = μ_X ± μ_Y. Variances always add, also for a difference: Var(X ± Y) = σ_X² + σ_Y², so σ = √(σ_X² + σ_Y²). Standard deviations never add directly. The total of n independent items with the same distribution has mean n·μ and standard deviation σ·√n. Then standardise as usual: z = (x − mean)/σ and read Φ(z).