Hydrostatic force
- Pressure at depth
- p = ρgh
- Force on a vertical wall
- F = ρg·hc·A
- Centre of pressure
- yp = yc + Ic/(ycA)
- Rectangle
- Ic = bH³/12
Fluid Mechanics: cram pack
Formula sheets, the key method steps for every topic and 8 practice problems, with full solutions at the back.
1Formulas and methods
Continuity & Bernoulli
- Continuity
- A1v1 = A2v2
- Bernoulli
- p1 + ½ρv1² + ρgz1 = p2 + ½ρv2² + ρgz2
- Flow rate
- Q = A·v
- Circle area
- A = πd²/4
Pipe friction & head loss
- Reynolds number
- Re = V·D/ν = ρ·V·D/μ
- Flow regime
- laminar below Re ≈ 2000, turbulent above Re ≈ 4000
- Mean velocity
- V = Q/A, A = π·D²/4
- Darcy–Weisbach
- hf = f·(L/D)·V²/(2g)
- Minor losses
- hm = ΣK·V²/(2g)
- Typical K values
- entrance 0.5, exit 1.0, 90° bend ≈ 0.3
- Pressure drop
- Δp = ρ·g·hf
- Two open reservoirs
- Δz = (f·L/D + ΣK)·V²/(2g)
- Free outlet
- H = (1 + f·L/D + ΣK)·V²/(2g)
Pumps & pump power
- Hydraulic power
- Ph = ρ·g·Q·H = Q·Δp
- Shaft power
- Pshaft = Ph/ηpump
- Electrical power
- Pel = Pshaft/ηmotor
- Pump head
- H = Δz + Δp/(ρ·g) + hL
- System losses
- hL = (f·L/D + ΣK)·V²/(2g)
2Practice problems
1.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 0.5 mH = 2.5 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
2.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1.5 mH = 2 mb = 1 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
3.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 200 mm to 40 mm. In the wide section the pressure is 330 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
d1 = 200 mmd2 = 40 mmp1 = 330 kPav1 = 0.5 m/sρ = 1000 kg/m³
p2 = kPa
4.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 140 kPa. Water leaves through an opening with a diameter of 40 mm, 1.5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
pair = 140 kPa (gauge)h = 1.5 md = 40 mmρ = 1000 kg/m³g = 9.81 m/s²
v = m/s
5.Pipe friction & head lossMedium
Water flows at 4 L/s through a pipe 300 m long with an inside diameter of 100 mm. Use the Darcy friction factor f = 0.028 and g = 9.81 m/s². Find the friction head loss hf.
Q = 4 L/sL = 300 mD = 100 mmf = 0.028g = 9.81 m/s²
hf = m
6.Pipe friction & head lossHard
Two open reservoirs are joined by a pipe 300 m long with an inside diameter of 200 mm and a Darcy friction factor f = 0.018. The water surface of the upper reservoir is 10 m above that of the lower one. The minor losses are a square-edged entrance (K = 0.5), 2 bends (K = 0.3 each), a valve (K = 10) and the exit into the lower reservoir (K = 1.0). Use g = 9.81 m/s². Find the flow rate Q in L/s.
Δz = 10 mL = 300 mD = 200 mmf = 0.018Kentrance = 0.5Kbend = 0.3 (×2)Kvalve = 10Kexit = 1.0
Q = L/s
7.Pumps & pump powerMedium
A pump with an efficiency of 65% delivers 150 L/s of water (ρ = 1000 kg/m³) against a head of 54 m. Use g = 9.81 m/s². Find the shaft power Pshaft needed, in kW.
Q = 150 L/sH = 54 mη = 65%g = 9.81 m/s²
Pshaft = kW
8.Pumps & pump powerHard
A pump moves 25 L/s of water (ρ = 1000 kg/m³) from an open lower reservoir to an upper tank whose water surface is 6 m higher. The pipe is 200 m long with an inside diameter of 150 mm and a Darcy friction factor f = 0.022; the minor-loss coefficients add up to ΣK = 8 (entrance and exit included). Use g = 9.81 m/s². The upper tank is closed and the air above its water is at a gauge pressure of 300 kPa. Find the head H the pump must add.
Q = 25 L/sΔz = 6 mL = 200 mD = 150 mmf = 0.022ΣK = 8ptank = 300 kPa
H = m
3Solutions
1.Hydrostatic force
Answer: F = 85.84 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·5 = 85.84 kN
Answer
F = 85.84 kN
2.Hydrostatic force
Answer: F = 61.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.5·2 = 61.8 kN
Answer
F = 61.8 kN
3.Continuity & Bernoulli
Answer: p2 = 252 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 0.5·(200/40)² = 12.5 m/s
½ρ(v1² − v2²) = ½·1000·(0.5² − 12.5²)/1000 = −78 kPa
p2 = p1 + ½ρ(v1² − v2²) = 330 + (−78) = 252 kPa
Answer
p2 = 252 kPa
4.Continuity & Bernoulli
Answer: v = 17.59 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(140000/1000 + 9.81·1.5)) = 17.59 m/s
Answer
v = 17.59 m/s
5.Pipe friction & head loss
Answer: hf = 1.111 m
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Mean velocity
A = π·0.1²/4 = 0.007854 m²
V = Q/A = 0.004/0.007854 = 0.5093 m/s
Velocity head
V²/(2g) = 0.5093²/(2·9.81) = 0.01322 m
Darcy–Weisbach
hf = f·(L/D)·V²/(2g) = 0.028·(300/0.1)·0.5093²/(2·9.81) = 1.111 m
Answer
hf = 1.111 m
6.Pipe friction & head loss
Answer: Q = 70.37 L/s
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Loss coefficients
f·L/D = 0.018·300/0.2 = 27
ΣK = 0.5 + 2·0.3 + 10 + 1.0 = 12.1
Energy equation
Both surfaces are open to the air and practically at rest, so all of Δz is lost in the pipe.
10 = (27 + 12.1)·V²/(2·9.81)
V = √(2·9.81·10/39.1) = 2.24 m/s
Flow rate
Q = V·π·D²/4 = 2.24·0.03142 = 0.07037 m³/s = 70.37 L/s
Answer
Q = 70.37 L/s
7.Pumps & pump power
Answer: Pshaft = 122.2 kW
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Hydraulic power
Ph = ρ·g·Q·H = 1000·9.81·0.15·54 = 79.46 kW
Shaft power
Pshaft = Ph/η = 79.46/0.65 = 122.2 kW
Answer
Pshaft = 122.2 kW
8.Pumps & pump power
Answer: H = 40.39 m
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Velocity
V = Q/A = 0.025/0.01767 = 1.415 m/s
V²/(2g) = 0.102 m
Head losses
hL = (f·L/D + ΣK)·V²/(2g) = (29.33 + 8)·0.102 = 3.808 m
Pressure head
p/(ρ·g) = 300000/(1000·9.81) = 30.58 m
Pump head
Both surfaces are practically at rest, so there is no velocity head term.
H = Δz + p/(ρ·g) + hL = 6 + 30.58 + 3.808 = 40.39 m
Answer
H = 40.39 m
ExamProblems · examproblems.com/courses/fluid-mechanics