Hydrostatic force
- Pressure at depth
- p = ρgh
- Force on a vertical wall
- F = ρg·hc·A
- Centre of pressure
- yp = yc + Ic/(ycA)
- Rectangle
- Ic = bH³/12
Fluid Mechanics: cram pack
Formula sheets, the key method steps for every topic and 8 practice problems, with full solutions at the back.
1Formulas and methods
Continuity & Bernoulli
- Continuity
- A1v1 = A2v2
- Bernoulli
- p1 + ½ρv1² + ρgz1 = p2 + ½ρv2² + ρgz2
- Flow rate
- Q = A·v
- Circle area
- A = πd²/4
Pipe friction & head loss
- Reynolds number
- Re = V·D/ν = ρ·V·D/μ
- Flow regime
- laminar below Re ≈ 2000, turbulent above Re ≈ 4000
- Mean velocity
- V = Q/A, A = π·D²/4
- Darcy–Weisbach
- hf = f·(L/D)·V²/(2g)
- Minor losses
- hm = ΣK·V²/(2g)
- Typical K values
- entrance 0.5, exit 1.0, 90° bend ≈ 0.3
- Pressure drop
- Δp = ρ·g·hf
- Two open reservoirs
- Δz = (f·L/D + ΣK)·V²/(2g)
- Free outlet
- H = (1 + f·L/D + ΣK)·V²/(2g)
Pumps & pump power
- Hydraulic power
- Ph = ρ·g·Q·H = Q·Δp
- Shaft power
- Pshaft = Ph/ηpump
- Electrical power
- Pel = Pshaft/ηmotor
- Pump head
- H = Δz + Δp/(ρ·g) + hL
- System losses
- hL = (f·L/D + ΣK)·V²/(2g)
2Practice problems
1.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 0.5 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
2.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2.5 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
3.Continuity & BernoulliMedium
A pitot-static tube in a wind tunnel reads a difference of 650 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 650 Paρ = 1.2 kg/m³
v = m/s
4.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 9 m. At section 1 the pressure is 340 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
d1 = 100 mmd2 = 75 mmp1 = 340 kPav1 = 1.75 m/sΔz = 9 mρ = 1000 kg/m³
p2 = kPa
5.Pipe friction & head lossMedium
Water flows at a mean velocity of 2.3 m/s through a pipe 50 m long with an inside diameter of 250 mm. Use the Darcy friction factor f = 0.022 and g = 9.81 m/s². Find the friction head loss hf.
V = 2.3 m/sL = 50 mD = 250 mmf = 0.022g = 9.81 m/s²
hf = m
6.Pipe friction & head lossHard
A pipe 100 m long with an inside diameter of 150 mm (Darcy friction factor f = 0.015) runs from an open reservoir and discharges as a free jet into the air. The minor losses are a square-edged entrance (K = 0.5), 3 bends (K = 0.3 each) and a valve (K = 0.2). Use g = 9.81 m/s². How far H must the reservoir surface be above the pipe outlet for a flow rate of 25 L/s?
Q = 25 L/sL = 100 mD = 150 mmf = 0.015Kentrance = 0.5Kbend = 0.3 (×3)Kvalve = 0.2
H = m
7.Pumps & pump powerMedium
A pump with an efficiency of 80% delivers 150 L/s of water (ρ = 1000 kg/m³) against a head of 60 m. Use g = 9.81 m/s². Find the shaft power Pshaft needed, in kW.
Q = 150 L/sH = 60 mη = 80%g = 9.81 m/s²
Pshaft = kW
8.Pumps & pump powerHard
A pump moves 75 L/s of water (ρ = 1000 kg/m³) from an open lower reservoir to an upper tank whose water surface is 15 m higher. The pipe is 200 m long with an inside diameter of 200 mm and a Darcy friction factor f = 0.025; the minor-loss coefficients add up to ΣK = 8 (entrance and exit included). Use g = 9.81 m/s². The upper tank is closed and the air above its water is at a gauge pressure of 150 kPa. Find the head H the pump must add.
Q = 75 L/sΔz = 15 mL = 200 mD = 200 mmf = 0.025ΣK = 8ptank = 150 kPa
H = m
3Solutions
1.Hydrostatic force
Answer: F = 176.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·9 = 176.6 kN
Answer
F = 176.6 kN
2.Hydrostatic force
Answer: F = 353.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·9 = 353.2 kN
Answer
F = 353.2 kN
3.Continuity & Bernoulli
Answer: v = 32.91 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·650/1.2) = 32.91 m/s
Answer
v = 32.91 m/s
4.Continuity & Bernoulli
Answer: p2 = 248.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 1.75·(100/75)² = 3.111 m/s
½ρ(v1² − v2²) = ½·1000·(1.75² − 3.111²)/1000 = −3.308 kPa
ρgΔz = 1000·9.81·9/1000 = 88.29 kPa
p2 = p1 + ½ρ(v1² − v2²) − ρgΔz = 340 + (−3.308) − 88.29 = 248.4 kPa
Answer
p2 = 248.4 kPa
5.Pipe friction & head loss
Answer: hf = 1.186 m
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Velocity head
V²/(2g) = 2.3²/(2·9.81) = 0.2696 m
Darcy–Weisbach
hf = f·(L/D)·V²/(2g) = 0.022·(50/0.25)·2.3²/(2·9.81) = 1.186 m
Answer
hf = 1.186 m
6.Pipe friction & head loss
Answer: H = 1.285 m
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Velocity
V = Q/A = 0.025/0.01767 = 1.415 m/s
V²/(2g) = 0.102 m
Loss coefficients
f·L/D = 0.015·100/0.15 = 10
ΣK = 0.5 + 3·0.3 + 0.2 = 1.6
Energy equation
The outlet jet still carries its velocity head; it is not a loss but it has to be supplied.
H = (1 + 10 + 1.6)·0.102 = 1.285 m
Answer
H = 1.285 m
7.Pumps & pump power
Answer: Pshaft = 110.4 kW
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Hydraulic power
Ph = ρ·g·Q·H = 1000·9.81·0.15·60 = 88.29 kW
Shaft power
Pshaft = Ph/η = 88.29/0.8 = 110.4 kW
Answer
Pshaft = 110.4 kW
8.Pumps & pump power
Answer: H = 39.88 m
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Velocity
V = Q/A = 0.075/0.03142 = 2.387 m/s
V²/(2g) = 0.2905 m
Head losses
hL = (f·L/D + ΣK)·V²/(2g) = (25 + 8)·0.2905 = 9.586 m
Pressure head
p/(ρ·g) = 150000/(1000·9.81) = 15.29 m
Pump head
Both surfaces are practically at rest, so there is no velocity head term.
H = Δz + p/(ρ·g) + hL = 15 + 15.29 + 9.586 = 39.88 m
Answer
H = 39.88 m
ExamProblems · examproblems.com/courses/fluid-mechanics