Fluid Mechanics: cram pack

Formula sheets, the key method steps for every topic and 8 practice problems, with full solutions at the back.

New problems Back to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Hydrostatic force

Pressure at depth: p = ρgh
Force on a vertical wall: F = ρg·h_c·A
Centre of pressure: y_p = y_c + I_c/(y_cA)
Rectangle: I_c = bH³/12

Continuity & Bernoulli

Continuity: A₁v₁ = A₂v₂
Bernoulli: p₁ + ½ρv₁² + ρgz₁ = p₂ + ½ρv₂² + ρgz₂
Flow rate: Q = A·v
Circle area: A = πd²/4

Pipe friction & head loss

Reynolds number: Re = V·D/ν = ρ·V·D/μ
Flow regime: laminar below Re ≈ 2000, turbulent above Re ≈ 4000
Mean velocity: V = Q/A, A = π·D²/4
Darcy–Weisbach: h_f = f·(L/D)·V²/(2g)
Minor losses: h_m = ΣK·V²/(2g)
Typical K values: entrance 0.5, exit 1.0, 90° bend ≈ 0.3
Pressure drop: Δp = ρ·g·h_f
Two open reservoirs: Δz = (f·L/D + ΣK)·V²/(2g)
Free outlet: H = (1 + f·L/D + ΣK)·V²/(2g)

Pumps & pump power

Hydraulic power: P_h = ρ·g·Q·H = Q·Δp
Shaft power: P_shaft = P_h/η_pump
Electrical power: P_el = P_shaft/η_motor
Pump head: H = Δz + Δp/(ρ·g) + h_L
System losses: h_L = (f·L/D + ΣK)·V²/(2g)

2Practice problems

1.Hydrostatic forceMedium

A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.

d = 2 mH = 2 mb = 1.5 mρ = 1000 kg/m³g = 9.81 m/s²

F = kN

2.Hydrostatic forceHard

A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.

d = 2.5 mH = 2.5 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²

F = kN

3.Continuity & BernoulliMedium

Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 57 kPa higher than at the throat. Ignoring losses, find the flow rate Q.

d₁ = 100 mmd₂ = 60 mmp₁ − p₂ = 57 kPaρ = 1000 kg/m³

Q = L/s

4.Continuity & BernoulliHard

Water flows up through a pipe that narrows from 150 mm to 75 mm while rising 8 m. At section 1 the pressure is 250 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p₂ at section 2.

d₁ = 150 mmd₂ = 75 mmp₁ = 250 kPav₁ = 1.5 m/sΔz = 8 mρ = 1000 kg/m³

p₂ = kPa

5.Pipe friction & head lossMedium

Water (ρ = 1000 kg/m³) flows at 2.7 m/s through a horizontal pipe, 300 m long, with an inside diameter of 150 mm. Use the Darcy friction factor f = 0.022 and g = 9.81 m/s². Find the pressure drop Δp over the pipe in kPa.

V = 2.7 m/sL = 300 mD = 150 mmf = 0.022ρ = 1000 kg/m³

Δp = kPa

6.Pipe friction & head lossHard

Two open reservoirs are joined by a pipe 100 m long with an inside diameter of 150 mm and a Darcy friction factor f = 0.018. The water surface of the upper reservoir is 24 m above that of the lower one. The minor losses are a square-edged entrance (K = 0.5), 2 bends (K = 0.3 each), a valve (K = 10) and the exit into the lower reservoir (K = 1.0). Use g = 9.81 m/s². Find the flow rate Q in L/s.

Δz = 24 mL = 100 mD = 150 mmf = 0.018K_entrance = 0.5K_bend = 0.3 (×2)K_valve = 10K_exit = 1.0

Q = L/s

7.Pumps & pump powerMedium

A pump delivers 25 L/s of water (ρ = 1000 kg/m³) against a head of 32 m. The pump efficiency is 60% and the electric motor driving it has an efficiency of 94%. Use g = 9.81 m/s². Find the electrical power P_el the motor draws, in kW.

Q = 25 L/sH = 32 mη_pump = 60%η_motor = 94%g = 9.81 m/s²

P_el = kW

8.Pumps & pump powerHard

A pump moves 15 L/s of water (ρ = 1000 kg/m³) from an open lower reservoir to an upper tank whose water surface is 6 m higher. The pipe is 300 m long with an inside diameter of 100 mm and a Darcy friction factor f = 0.02; the minor-loss coefficients add up to ΣK = 8 (entrance and exit included). Use g = 9.81 m/s². The upper tank is closed and the air above its water is at a gauge pressure of 200 kPa. Find the head H the pump must add.

Q = 15 L/sΔz = 6 mL = 300 mD = 100 mmf = 0.02ΣK = 8p_tank = 200 kPa

H = m

3Solutions

1.Hydrostatic force

Answer: F = 88.29 kN

Hydrostatic force on a plane surface: F = ρ·g·y_c·A. It acts at the centre of pressure, y_cp = y_c + I_c/(y_cA), which always lies below the centroid.

Centroid depth and area

y_c = d + H/2 = 2 + 2/2 = 3 m

A = H·b = 2·1.5 = 3 m²

Resultant force

F = ρ·g·y_c·A = 1000·9.81·3·3 = 88.29 kN

Answer

F = 88.29 kN

2.Hydrostatic force

Answer: F = 80.93 kN

Hydrostatic force on a plane surface: F = ρ·g·y_c·A. It acts at the centre of pressure, y_cp = y_c + I_c/(y_cA), which always lies below the centroid.

Centroid depth and area

y_c = d + H/2 = 2.5 + 2.5/2 = 3.75 m

A = H·b = 2.5·1 = 2.5 m²

Resultant force

F = ρ·g·y_c·A = 880·9.81·3.75·2.5 = 80.93 kN

Answer

F = 80.93 kN

3.Continuity & Bernoulli

Answer: Q = 32.36 L/s

Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.

Continuity

v₁ = v₂·(60/100)² = 0.36·v₂

Bernoulli between inlet and throat

The pipe is horizontal, so only pressure and velocity change.

p₁ − p₂ = ½ρv₂²(1 − β⁴)

v₂ = √(2·57000/(1000·(1 − 0.1296))) = 11.44 m/s

v₁ = 4.12 m/s

Flow rate

Q = A₂·v₂ = 0.002827·11.44 = 0.03236 m³/s = 32.36 L/s

Answer

Q = 32.36 L/s

4.Continuity & Bernoulli

Answer: p₂ = 154.6 kPa

Continuity and Bernoulli

Work in Pa, then divide by 1000 to get kPa.

v₂ = v₁·(d₁/d₂)² = 1.5·(150/75)² = 6 m/s

½ρ(v₁² − v₂²) = ½·1000·(1.5² − 6²)/1000 = −16.88 kPa

ρgΔz = 1000·9.81·8/1000 = 78.48 kPa

p₂ = p₁ + ½ρ(v₁² − v₂²) − ρgΔz = 250 + (−16.88) − 78.48 = 154.6 kPa

Answer

p₂ = 154.6 kPa

5.Pipe friction & head loss

Answer: Δp = 160.4 kPa

Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss h_f = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses h_m = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = h_f + h_m, with the exit loss K = 1 included.

Head loss

h_f = f·(L/D)·V²/(2g) = 0.022·(300/0.15)·2.7²/(2·9.81) = 16.35 m

Pressure drop

The pipe is horizontal and the velocity does not change, so the energy equation reduces to Δp = ρ·g·h_f.

Δp = ρ·g·h_f = 1000·9.81·16.35 = 160380 Pa = 160.4 kPa

Answer

Δp = 160.4 kPa

6.Pipe friction & head loss

Answer: Q = 78.11 L/s

Loss coefficients

f·L/D = 0.018·100/0.15 = 12

ΣK = 0.5 + 2·0.3 + 10 + 1.0 = 12.1

Energy equation

Both surfaces are open to the air and practically at rest, so all of Δz is lost in the pipe.

24 = (12 + 12.1)·V²/(2·9.81)

V = √(2·9.81·24/24.1) = 4.42 m/s

Flow rate

Q = V·π·D²/4 = 4.42·0.01767 = 0.07811 m³/s = 78.11 L/s

Answer

Q = 78.11 L/s

7.Pumps & pump power

Answer: P_el = 13.91 kW

Pump power: the power given to the water is the hydraulic power P_h = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: P_shaft = P_h/η_pump, and the motor draws P_el = P_shaft/η_motor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.

Hydraulic power

P_h = ρ·g·Q·H = 1000·9.81·0.025·32 = 7.848 kW

Shaft power

P_shaft = 7.848/0.6 = 13.08 kW

Electrical power

P_el = 13.08/0.94 = 13.91 kW

Answer

P_el = 13.91 kW

8.Pumps & pump power

Answer: H = 39.03 m

Velocity

V = Q/A = 0.015/0.007854 = 1.91 m/s

V²/(2g) = 0.1859 m

Head losses

h_L = (f·L/D + ΣK)·V²/(2g) = (60 + 8)·0.1859 = 12.64 m

Pressure head

p/(ρ·g) = 200000/(1000·9.81) = 20.39 m

Pump head

Both surfaces are practically at rest, so there is no velocity head term.

H = Δz + p/(ρ·g) + h_L = 6 + 20.39 + 12.64 = 39.03 m

Answer

H = 39.03 m

ExamProblems · examproblems.com/courses/fluid-mechanics