Hydraulic Engineering: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Hydrostatic force

Pressure at depth
p = ρgh
Force on a vertical wall
F = ρg·hc·A
Centre of pressure
yp = yc + Ic/(ycA)
Rectangle
Ic = bH³/12

Continuity & Bernoulli

Continuity
A1v1 = A2v2
Bernoulli
p1 + ½ρv1² + ρgz1 = p2 + ½ρv2² + ρgz2
Flow rate
Q = A·v
Circle area
A = πd²/4

Pipe friction & head loss

Reynolds number
Re = V·D/ν = ρ·V·D/μ
Flow regime
laminar below Re ≈ 2000, turbulent above Re ≈ 4000
Mean velocity
V = Q/A, A = π·D²/4
Darcy–Weisbach
hf = f·(L/D)·V²/(2g)
Minor losses
hm = ΣK·V²/(2g)
Typical K values
entrance 0.5, exit 1.0, 90° bend ≈ 0.3
Pressure drop
Δp = ρ·g·hf
Two open reservoirs
Δz = (f·L/D + ΣK)·V²/(2g)
Free outlet
H = (1 + f·L/D + ΣK)·V²/(2g)

Pumps & pump power

Hydraulic power
Ph = ρ·g·Q·H = Q·Δp
Shaft power
Pshaft = Ph/ηpump
Electrical power
Pel = Pshaft/ηmotor
Pump head
H = Δz + Δp/(ρ·g) + hL
System losses
hL = (f·L/D + ΣK)·V²/(2g)

Open-channel flow (Manning)

Manning equation
V = (1/n)·R2/3·S1/2
Flow rate
Q = A·V
Hydraulic radius
R = A/P (P = wetted perimeter, free surface excluded)
Rectangle
A = b·y, P = b + 2y
Trapezoid (side slope z:1)
A = (b + z·y)·y, P = b + 2y·√(1 + z²)
Circular pipe, full or half full
R = D/4
Required slope
S = (n·Q/(A·R2/3))²

2Practice problems

1.Hydrostatic forceMedium
gated = 2 mH = 3 m

A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.

d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
2.Hydrostatic forceHard
gated = 1.5 mH = 2.5 m

A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.

d = 1.5 mH = 2.5 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
3.Continuity & BernoulliMedium
Q = ?d = 30 mm, Cd​ = 0.64h = 6 m

Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 6 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².

d = 30 mmh = 6 mCd = 0.64g = 9.81 m/s²
Q = L/s
4.Continuity & BernoulliHard
d1​ = 300 mmd2​ = 150 mm12Δh = 110 mmmercuryQ = ?

A horizontal venturi meter (inlet 300 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 110 mm. The discharge coefficient is 0.97. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².

d1 = 300 mmd2 = 150 mmΔh = 110 mmCd = 0.97ρHg = 13 600 kg/m³g = 9.81 m/s²
Q = L/s
5.Pipe friction & head lossMedium
V = 1 m/sD = 100 mmL = 100 mf = 0.025

Water flows at a mean velocity of 1 m/s through a pipe 100 m long with an inside diameter of 100 mm. Use the Darcy friction factor f = 0.025 and g = 9.81 m/s². Find the friction head loss hf.

V = 1 m/sL = 100 mD = 100 mmf = 0.025g = 9.81 m/s²
hf = m
6.Pipe friction & head lossHard
K = 10Δz = 31 mL = 100 m, D = 150 mm, f = 0.0223× bend (K = 0.3)

Two open reservoirs are joined by a pipe 100 m long with an inside diameter of 150 mm and a Darcy friction factor f = 0.022. The water surface of the upper reservoir is 31 m above that of the lower one. The minor losses are a square-edged entrance (K = 0.5), 3 bends (K = 0.3 each), a valve (K = 10) and the exit into the lower reservoir (K = 1.0). Use g = 9.81 m/s². Find the flow rate Q in L/s.

Δz = 31 mL = 100 mD = 150 mmf = 0.022Kentrance = 0.5Kbend = 0.3 (×3)Kvalve = 10Kexit = 1.0
Q = L/s
7.Pumps & pump powerMedium
PQ = 100 L/sH = 28 m

A pump with an efficiency of 82% delivers 100 L/s of water (ρ = 1000 kg/m³) against a head of 28 m. Use g = 9.81 m/s². Find the shaft power Pshaft needed, in kW.

Q = 100 L/sH = 28 mη = 82%g = 9.81 m/s²
Pshaft = kW
8.Pumps & pump powerHard
PQ = 50 L/sΔz = 5 mL = 200 m, D = 250 mm, f = 0.015, ΣK = 8

A pump moves 50 L/s of water (ρ = 1000 kg/m³) from an open lower reservoir to an upper tank whose water surface is 5 m higher. The pipe is 200 m long with an inside diameter of 250 mm and a Darcy friction factor f = 0.015; the minor-loss coefficients add up to ΣK = 8 (entrance and exit included). Use g = 9.81 m/s². Find the head H the pump must add.

Q = 50 L/sΔz = 5 mL = 200 mD = 250 mmf = 0.015ΣK = 8
H = m
9.Open-channel flow (Manning)Medium
b = 3 my = 0.5 mn = 0.014, S = 0.0015

A rectangular unfinished concrete channel is 3 m wide. Water flows uniformly 0.5 m deep. Manning n = 0.014 and the bed slope is S = 0.0015. Find the flow rate Q in m³/s.

b = 3 my = 0.5 mn = 0.014S = 0.0015
Q = m³/s
10.Open-channel flow (Manning)Hard
b = 4.5 my = 1.4 m1 : 1n = 0.014, Q = 18 m³/s

A trapezoidal unfinished concrete channel with a bottom width of 4.5 m and side slopes of 1:1 (horizontal:vertical) must carry 18 m³/s in uniform flow at a depth of 1.4 m. Manning n = 0.014. Find the required bed slope S (in m/m).

Q = 18 m³/sb = 4.5 my = 1.4 mz = 1n = 0.014
S = m/m

3Solutions

1.Hydrostatic force

Answer: F = 103 kN

Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.

Centroid depth and area

yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
gated = 2 mH = 3 mF

Resultant force

F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN

Answer

F = 103 kN
2.Hydrostatic force

Answer: ycp = 2.939 m

Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.

Centroid depth and area

yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·2 = 5 m²
gated = 1.5 mH = 2.5 mF

Resultant force

F = ρ·g·yc·A = 1260·9.81·2.75·5 = 170 kN

Centre of pressure

Pressure grows with depth, so the resultant acts below the centroid.

Ic = b·H³/12 = 2·2.5³/12 = 2.604 m⁴
ycp = yc + Ic/(yc·A) = 2.75 + 2.604/(2.75·5) = 2.939 m

Answer

ycp = 2.939 m
3.Continuity & Bernoulli

Answer: Q = 4.908 L/s

Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.

Ideal jet velocity

√(2gh) = √(2·9.81·6) = 10.85 m/s

Actual flow rate

The discharge coefficient accounts for the contraction of the jet and friction at the edge.

Q = Cd·A·√(2gh) = 0.64·0.0007069·10.85 = 0.004908 m³/s = 4.908 L/s

Answer

Q = 4.908 L/s
4.Continuity & Bernoulli

Answer: Q = 92.32 L/s

Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.

Pressure difference from the manometer

Δp = (13600 − 1000)·9.81·0.11 = 13597 Pa

Throat velocity

Continuity and Bernoulli together give the ideal throat velocity.

β = 150/300 = 0.5
v2 = √(2·13597/(1000·(1 − 0.0625))) = 5.386 m/s

Actual flow rate

Q = Cd·A2·v2 = 0.97·0.01767·5.386 = 0.09232 m³/s = 92.32 L/s

Answer

Q = 92.32 L/s
5.Pipe friction & head loss

Answer: hf = 1.274 m

Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.

Velocity head

V²/(2g) = 1²/(2·9.81) = 0.05097 m

Darcy–Weisbach

hf = f·(L/D)·V²/(2g) = 0.025·(100/0.1)·1²/(2·9.81) = 1.274 m

Answer

hf = 1.274 m
6.Pipe friction & head loss

Answer: Q = 83.77 L/s

Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.

Loss coefficients

f·L/D = 0.022·100/0.15 = 14.67
ΣK = 0.5 + 3·0.3 + 10 + 1.0 = 12.4

Energy equation

Both surfaces are open to the air and practically at rest, so all of Δz is lost in the pipe.

31 = (14.67 + 12.4)·V²/(2·9.81)
V = √(2·9.81·31/27.07) = 4.74 m/s

Flow rate

Q = V·π·D²/4 = 4.74·0.01767 = 0.08377 m³/s = 83.77 L/s

Answer

Q = 83.77 L/s
7.Pumps & pump power

Answer: Pshaft = 33.5 kW

Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.

Hydraulic power

Ph = ρ·g·Q·H = 1000·9.81·0.1·28 = 27.47 kW

Shaft power

Pshaft = Ph/η = 27.47/0.82 = 33.5 kW

Answer

Pshaft = 33.5 kW
8.Pumps & pump power

Answer: H = 6.058 m

Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.

Velocity

V = Q/A = 0.05/0.04909 = 1.019 m/s
V²/(2g) = 0.05288 m

Head losses

hL = (f·L/D + ΣK)·V²/(2g) = (12 + 8)·0.05288 = 1.058 m

Pump head

Both surfaces are open and practically at rest, so pressure and velocity terms drop out.

H = Δz + hL = 5 + 1.058 = 6.058 m

Answer

H = 6.058 m
9.Open-channel flow (Manning)

Answer: Q = 2.158 m³/s

Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R2/3·S1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.

Geometry

A = b·y = 3·0.5 = 1.5 m²
P = b + 2y = 3 + 2·0.5 = 4 m
R = A/P = 0.375 m

Velocity

V = (1/0.014)·0.3752/3·0.00151/2 = 1.439 m/s

Flow rate

Q = A·V = 1.5·1.439 = 2.158 m³/s

Answer

Q = 2.158 m³/s
10.Open-channel flow (Manning)

Answer: S = 0.0009609 m/m

Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R2/3·S1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.

Geometry

A = (b + z·y)·y = (4.5 + 1·1.4)·1.4 = 8.26 m²
P = b + 2y·√(1 + z²) = 4.5 + 2·1.4·√(1 + 1²) = 8.46 m
R = A/P = 0.9764 m

Solve Manning for S

S1/2 = n·Q/(A·R2/3) = 0.014·18/(8.26·0.9842) = 0.031
S = 0.031² = 0.0009609

Answer

S = 0.0009609

That is a fall of 0.9609 m per kilometre.

ExamProblems · examproblems.com/courses/hydraulic-engineering