Hydrostatic force
- Pressure at depth
- p = ρgh
- Force on a vertical wall
- F = ρg·hc·A
- Centre of pressure
- yp = yc + Ic/(ycA)
- Rectangle
- Ic = bH³/12
Hydraulic Engineering: cram pack
Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
1Formulas and methods
Continuity & Bernoulli
- Continuity
- A1v1 = A2v2
- Bernoulli
- p1 + ½ρv1² + ρgz1 = p2 + ½ρv2² + ρgz2
- Flow rate
- Q = A·v
- Circle area
- A = πd²/4
Pipe friction & head loss
- Reynolds number
- Re = V·D/ν = ρ·V·D/μ
- Flow regime
- laminar below Re ≈ 2000, turbulent above Re ≈ 4000
- Mean velocity
- V = Q/A, A = π·D²/4
- Darcy–Weisbach
- hf = f·(L/D)·V²/(2g)
- Minor losses
- hm = ΣK·V²/(2g)
- Typical K values
- entrance 0.5, exit 1.0, 90° bend ≈ 0.3
- Pressure drop
- Δp = ρ·g·hf
- Two open reservoirs
- Δz = (f·L/D + ΣK)·V²/(2g)
- Free outlet
- H = (1 + f·L/D + ΣK)·V²/(2g)
Pumps & pump power
- Hydraulic power
- Ph = ρ·g·Q·H = Q·Δp
- Shaft power
- Pshaft = Ph/ηpump
- Electrical power
- Pel = Pshaft/ηmotor
- Pump head
- H = Δz + Δp/(ρ·g) + hL
- System losses
- hL = (f·L/D + ΣK)·V²/(2g)
Open-channel flow (Manning)
- Manning equation
- V = (1/n)·R2/3·S1/2
- Flow rate
- Q = A·V
- Hydraulic radius
- R = A/P (P = wetted perimeter, free surface excluded)
- Rectangle
- A = b·y, P = b + 2y
- Trapezoid (side slope z:1)
- A = (b + z·y)·y, P = b + 2y·√(1 + z²)
- Circular pipe, full or half full
- R = D/4
- Required slope
- S = (n·Q/(A·R2/3))²
2Practice problems
1.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 0.5 mH = 2.5 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
2.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2.5 mH = 1.5 mb = 1.5 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
3.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 25 mm. In the wide section the pressure is 270 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
d1 = 100 mmd2 = 25 mmp1 = 270 kPav1 = 0.5 m/sρ = 1000 kg/m³
p2 = kPa
4.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 160 kPa. Water leaves through an opening with a diameter of 30 mm, 2.5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
pair = 160 kPa (gauge)h = 2.5 md = 30 mmρ = 1000 kg/m³g = 9.81 m/s²
v = m/s
5.Pipe friction & head lossMedium
Water flows at a mean velocity of 2.4 m/s through a pipe 400 m long with an inside diameter of 75 mm. Use the Darcy friction factor f = 0.018 and g = 9.81 m/s². Find the friction head loss hf.
V = 2.4 m/sL = 400 mD = 75 mmf = 0.018g = 9.81 m/s²
hf = m
6.Pipe friction & head lossHard
Two open reservoirs are joined by a pipe 200 m long with an inside diameter of 200 mm and a Darcy friction factor f = 0.02. The minor losses are a square-edged entrance (K = 0.5), 4 bends (K = 0.3 each), a valve (K = 0.2) and the exit into the lower reservoir (K = 1.0). Use g = 9.81 m/s². What difference in water level Δz between the reservoirs gives a flow rate of 80 L/s?
Q = 80 L/sL = 200 mD = 200 mmf = 0.02Kentrance = 0.5Kbend = 0.3 (×4)Kvalve = 0.2Kexit = 1.0
Δz = m
7.Pumps & pump powerMedium
A pump with an efficiency of 60% delivers 20 L/s of water (ρ = 1000 kg/m³) against a head of 50 m. Use g = 9.81 m/s². Find the shaft power Pshaft needed, in kW.
Q = 20 L/sH = 50 mη = 60%g = 9.81 m/s²
Pshaft = kW
8.Pumps & pump powerHard
A pump moves 75 L/s of water (ρ = 1000 kg/m³) from an open lower reservoir to an upper tank whose water surface is 6 m higher. The pipe is 200 m long with an inside diameter of 250 mm and a Darcy friction factor f = 0.015; the minor-loss coefficients add up to ΣK = 6 (entrance and exit included). Use g = 9.81 m/s². The upper tank is closed and the air above its water is at a gauge pressure of 350 kPa. Find the head H the pump must add.
Q = 75 L/sΔz = 6 mL = 200 mD = 250 mmf = 0.015ΣK = 6ptank = 350 kPa
H = m
9.Open-channel flow (Manning)Medium
A trapezoidal clean earth channel has a bottom width of 5.5 m and side slopes of 2:1 (horizontal:vertical). Water flows uniformly 2.3 m deep. Manning n = 0.022 and the bed slope is S = 0.005. Find the flow rate Q in m³/s.
b = 5.5 my = 2.3 mz = 2n = 0.022S = 0.005
Q = m³/s
10.Open-channel flow (Manning)Hard
A concrete sewer with an inside diameter of 450 mm (Manning n = 0.013) must reach a self-cleansing velocity of 1.2 m/s when flowing just full. Find the minimum slope S (in m/m).
D = 450 mmn = 0.013V = 1.2 m/s
S = m/m
3Solutions
1.Hydrostatic force
Answer: F = 42.92 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·2.5 = 42.92 kN
Answer
F = 42.92 kN
2.Hydrostatic force
Answer: F = 90.39 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.25·2.25 = 90.39 kN
Answer
F = 90.39 kN
3.Continuity & Bernoulli
Answer: p2 = 238.1 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 0.5·(100/25)² = 8 m/s
½ρ(v1² − v2²) = ½·1000·(0.5² − 8²)/1000 = −31.88 kPa
p2 = p1 + ½ρ(v1² − v2²) = 270 + (−31.88) = 238.1 kPa
Answer
p2 = 238.1 kPa
4.Continuity & Bernoulli
Answer: v = 19.21 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(160000/1000 + 9.81·2.5)) = 19.21 m/s
Answer
v = 19.21 m/s
5.Pipe friction & head loss
Answer: hf = 28.18 m
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Velocity head
V²/(2g) = 2.4²/(2·9.81) = 0.2936 m
Darcy–Weisbach
hf = f·(L/D)·V²/(2g) = 0.018·(400/0.075)·2.4²/(2·9.81) = 28.18 m
Answer
hf = 28.18 m
6.Pipe friction & head loss
Answer: Δz = 7.569 m
Pipe flow: the Reynolds number Re = V·D/ν = ρ·V·D/μ tells laminar flow (Re below about 2000) from turbulent flow (above about 4000). Friction along a pipe costs the Darcy–Weisbach head loss hf = f·(L/D)·V²/(2g). Fittings, valves, the entrance and the exit add minor losses hm = ΣK·V²/(2g). Between two open reservoir surfaces the energy equation gives Δz = hf + hm, with the exit loss K = 1 included.
Velocity
V = Q/A = 0.08/0.03142 = 2.546 m/s
V²/(2g) = 0.3305 m
Loss coefficients
f·L/D = 0.02·200/0.2 = 20
ΣK = 0.5 + 4·0.3 + 0.2 + 1.0 = 2.9
Total head loss
hf = 20·0.3305 = 6.61 m
hm = 2.9·0.3305 = 0.9585 m
Δz = hf + hm = 7.569 m
Answer
Δz = 7.569 m
7.Pumps & pump power
Answer: Pshaft = 16.35 kW
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Hydraulic power
Ph = ρ·g·Q·H = 1000·9.81·0.02·50 = 9.81 kW
Shaft power
Pshaft = Ph/η = 9.81/0.6 = 16.35 kW
Answer
Pshaft = 16.35 kW
8.Pumps & pump power
Answer: H = 43.82 m
Pump power: the power given to the water is the hydraulic power Ph = ρ·g·Q·H = Q·Δp. The shaft must deliver more because the pump loses some: Pshaft = Ph/ηpump, and the motor draws Pel = Pshaft/ηmotor. The pump head H follows from the energy equation: static lift + pressure head + all friction and minor losses.
Velocity
V = Q/A = 0.075/0.04909 = 1.528 m/s
V²/(2g) = 0.119 m
Head losses
hL = (f·L/D + ΣK)·V²/(2g) = (12 + 6)·0.119 = 2.142 m
Pressure head
p/(ρ·g) = 350000/(1000·9.81) = 35.68 m
Pump head
Both surfaces are practically at rest, so there is no velocity head term.
H = Δz + p/(ρ·g) + hL = 6 + 35.68 + 2.142 = 43.82 m
Answer
H = 43.82 m
9.Open-channel flow (Manning)
Answer: Q = 96.6 m³/s
Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R2/3·S1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.
Geometry
A = (b + z·y)·y = (5.5 + 2·2.3)·2.3 = 23.23 m²
P = b + 2y·√(1 + z²) = 5.5 + 2·2.3·√(1 + 2²) = 15.79 m
R = A/P = 1.472 m
Velocity
V = (1/0.022)·1.4722/3·0.0051/2 = 4.158 m/s
Flow rate
Q = A·V = 23.23·4.158 = 96.6 m³/s
Answer
Q = 96.6 m³/s
10.Open-channel flow (Manning)
Answer: S = 0.004481 m/m
Manning’s equation (SI): for uniform flow in an open channel V = (1/n)·R2/3·S1/2 and Q = A·V, with n the roughness coefficient, S the bed slope (m/m) and R = A/P the hydraulic radius: flow area divided by wetted perimeter. Only the boundary in contact with the water counts in P, not the free surface. Rectangle: A = b·y, P = b + 2y. Trapezoid with side slopes z:1 (horizontal:vertical): A = (b + z·y)·y, P = b + 2y·√(1 + z²). A circular pipe flowing full or half full has R = D/4.
Hydraulic radius
R = D/4 = 0.45/4 = 0.1125 m
Solve Manning for S
S = (n·V/R2/3)² = (0.013·1.2/0.233)² = 0.004481
Answer
S = 0.004481
That is a fall of 4.481 m per kilometre.
ExamProblems · examproblems.com/courses/hydraulic-engineering